![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www.fairchildsemi.com FAN7527B Power Factor Correction Controller Features * Internal Start-Up Timer * Internal R/C Filter Eliminates the Need for an External R/C Filter * Very Precise Adjustable Output Over Voltage Protection * Zero Current Detector * One Quadrant Multiplier * Trimmed 1.5% Internal Bandgap Reference * Under Voltage Lockout with 3V of Hysteresis * Totem Pole Output with High State Clamp * Low Start-Up and Operating Current * 8-Pin DIP or 8-Pin SOP Description The FAN7527B provides simple and high performance active power factor correction. The FAN7527B is optimized for electronic ballasts and low power and high density power supplies which require minimum board size, reduced external components and low power dissipation. Because the R/C filter is included in the current sense block, the external R/C filter is not necessary. Special circuitry has also been added to prevent no load runaway conditions. Regardless of the supply voltage, the output drive clamping circuit limits the overshoot of the power MOSFET gate drive. It greatly enhances the system reliability. Applications * Electronic Ballast * SMPS 8-DIP 1 8-SOP 1 Rev 1.0.0 (c)2001 Fairchild Semiconductor Corporation FAN7527B Internal Block Diagram Vcc 8 2.5V Ref Vcc + - 11.5V 8.5V UVLO Internal Bias Drive Output Timer R 7 OUT Idet 5 7.2V 2V 1.5V + - Zero Current Detector S Q Static OVP 40k CS 4 8pF + - R Current Sense Comparator Vref Veao(L)=2.25V + - 2.25V 1.8V Vmo MULT 3 Vm1 0 ~ 3.8V Multiplier Vmo K= Vm1 (Vm2 - Vref ) - + 0.25V Vm2 Vref~Vref+2.5V Isovp=30uA Idovp=40uA + - Vref Vea(-) 1 INV OVP Current Detector 6 GND 2 EA_OUT Error Amp 2 FAN7527B PIN Description INV 1 2 3 4 (Top View) 8 7 6 5 Vcc OUT GND ldet EA_OUT MULT CS Pin Number 1 2 3 4 5 6 7 8 Pin Name INV EA_OUT MULT CS ldet GND OUT Vcc Pin Function Description Inverting input of the error amplifier. The output of the boost converter should be resistively divided to 2.5V and connected to this pin. The output of the error amplifier. A feedback compensation network is placed between this pin and the INV pin. Input to the multiplier stage. The full-wave rectified AC voltage is devided to less than 2V and is connected to this pin. Input of the PWM comparator. The MOSFET current is sensed by a resistor and the resulting voltage is applied to this pin. An internal R/C filter is included to reject any high frequency noise. Zero current detection input. If it is connected to GND, the device is disabled. The ground potential of all the pins. Gate driver output. The push pull output stage is able to drive the Power MOSFET with peak current of 500mA. Supply voltage of driver and control circuits. 3 FAN7527B Absolute Maximum Ratings (Ta=25C) Characteristics Supply Voltage Peak Drive Output Current Driver Output Clamping Diodes Vo > Vcc or Vo < -0.3V Detector Clamping Diodes Error Amp, Multiplier and Comparator Input Voltages Operating Junction Temperature Operating Temperature Range Storage Temperature Range Power Dissipation Symbol VCC IOH,IOL lclamp ldet Vin Tj Topr Tstg Pd Value 30 500 10 10 -0.3 to 6 150 -25 to 125 -65 to 150 0.8 Unit V mA mA mA V C C C W Temperature Characteristics (-25C Ta 125C) Characteristics Temperature Stability for Reference Voltage (Vref) Temperature Stability for Multiplier Gain (K) Symbol Vref K/T Min. Typ. 20 -0.2 Max. Unit mV %/C 4 FAN7527B Electrical Characteristics VCC= 14V, -25C Ta 125C, unless otherwise stated. Characteristics Start Threshold Voltage UVLO Hysteresis < SUPPLY CURRENT SECTION > Start-up Supply Current Operating Supply Current Operating Current at OVP Dynamic Operating Supply Current < ERROR AMPLIFIER SECTION > Voltage Feedback Input Threshold Line Regulation Temperature Stability of Vref (Note1) Input Bias Current Output Source Current Output Sink Current Output Upper Clamp Voltage (Note2) Output Lower Clamp Voltage (Note3) Large Signal Open Loop Gain (Note4) Power Supply Rejection Ratio (Note5) Unity Gain Bandwidth (Note6) Slew Rate (Note7) < MULTIPLIER SECTION> Input Bias Current (Pin3) M1 Input Voltage Range (Pin3) M2 Input Voltage Range (Pin2) Multiplier Gain (Note8) Maximum Multiplier Output Voltage Temperature Stability of K (Note9) Ib(m) Vm1 Vm2 K K/T Vm1 = 1V, Vm2 = 3.5V -25 Ta 125C -0.5 0 Vref 0.36 1.65 0.44 1.8 -0.2 0.5 3.8 Vref+2.5 0.52 1.95 uA V V 1/V V %/C Vref Vref1 Vref3 Ib(ea) Isource Isink Veao(H) Veao(L) Gv PSRR GBW SR Vm2 = 4V Vm2 = 4V Isource = 0.1mA Isink = 0.1mA 14V Vcc 25V Iref =0mA, Ta =25C -25 Ta 125C 14V Vcc 25V -25 Ta 125C 2.465 2.44 -0.5 -2 2 60 60 2.5 2.5 0.1 20 -4 4 6 2.25 80 80 1 0.6 2.535 2.56 10 0.5 V V mV mV uA mA mA V V dB dB MHz V/us Ist Icc Icc(ovp) Idcc Vcc =Vth(st) -0.2V Output not switching Vinv = 3V 50KHz, CI = 1nF 10 60 3 1.7 4 100 6 4 8 uA mA mA mA Symbol Vth(st) HY(st) Test Condition Vcc Increasing - Min. 10.5 2 Typ. 11.5 3 Max. 12.5 4 Unit V V < UNDER VOLTAGE LOCKOUT SECTION> Vomax(m) Vinv =0V, Vm1 = 4V 5 FAN7527B Electrical Characteristics (Continued) VCC= 14V, -25C Ta 125C, unless otherwise stated. Characteristics < CURRENT SENSE SECTION> Input Offset Voltage (Note8) Input Bias Current Current Sense Delay to Output (Note11) Input Voltage Threshold Detect Hysteresis Input Low Clamp Voltage Input High Clamp Voltage Input Bias Current Input High/Low Clamp Diode Current (Note12) < OUTPUT SECTION > Output Voltage High Output Voltage Low Rising Time (Note13) Falling Time (Note14) Maximum Output Voltage Output Voltage with UVLO Activated < RESTART TIMER SECTION> Restart Time Delay Soft OVP Detecting Current Dynamic OVP Detecting Current Static OVP Threshold Voltage Symbol Vio(cs) Ib(cs) tb(cs) Test Condition Vm1=0V , Vm2 = 2.2V 0V Vcs 1.7V - Min. -10 -1 - Typ. 3 -0.1 200 Max. 10 1 500 Unit mV uA ns < ZERO CURRENT DETECT SECTION > Vth(det) HY(det) Vclamp(I) Ib(det) Iclamp(d) Vclamp(h) Idet = 3mA 1V Vdet 5V Vdet Increasing Idet = -100uA 1.7 0.2 0.45 6.5 -1 2 0.5 0.75 7.2 -0.1 2.3 0.8 1 7.9 1 3 V V V V uA mA Voh VoI tr tf Vomax(o) Vomin(o) td(rst) Isovp Idovp Vovp Io = -10mA Io = 10mA CI = 1nF CI = 1nF Vcc = 20V, Io = 100uA Vcc = 5V , Io = 100uA Vm1 = 1V, Vm2 = 3.5V Vinv = 2.7V 10.5 12 25 35 2.1 11 0.8 130 50 14 150 30 40 2.25 1 200 120 16 1 35 45 2.4 V V ns ns V V us uA uA V Note 1 ~ 14: These parameters, although guaranteed, are not 100% tested in production. Pin4_Threshold Multiplier Gain: K = ------------------------------------------------------ ...... ( Vm1 = Vpin3,Vm2 = Vpin2 ) Vm1 x ( Vm2 - Vref ) 6 FAN7527B Typical Performance Characteristics Fig.1 E.A. Output Voltage vs. C.S. Threshold 2.0 Vm1=3.0V Vm1=2.5V Vm1=2.0V Vm1=3.5V Fig.2 Multiplier Input Voltage vs. C.S. Threshold 2.0 1.8 Veao=4.25V Veao=4.0V Veao=3.75V CS ThresholdVoltage(V) C.S Threshold Voltage(V) CS Threshold Voltage(V) C.S. Threshold Voltage(V) 1.5 Vm1=4.0V Vm1=1.5V 1.6 1.4 1.2 Veao=4.5V Veao=3.5V Veao=3.25V Vm1=1.0V 1.0 Veao=3.0V 1.0 0.8 Veao=2.75V 0.6 0.4 0.2 Veao=2.5V Vm1=0.5V 0.5 Vm1=0V 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0 1 2 3 4 5 EA Output Voltage(V) Multiplier Input Voltage(V) Figure 1. Error Amplifier Output Voltage vs Current Sensing Threshold Fig.3 Supply Current vs. Supply Voltage 0.015 Figure 2. Multiplier Input Voltage vs Current Sensing Threshold Fig.4 Reference Voltage vs. Temperature 2.7 0.012 0.009 Reference Voltage(V) 0 10 20 30 40 50 2.6 Supply Current(A) 2.5 0.006 2.4 0.003 0.000 2.3 -25 0 25 50 75 100 125 Supply Voltage(V) Temperature () Figure 3. Supply Current vs Supply Voltage Fig.5 Start-up Threshold vs. Temperature 14 12 10 8 6 4 2 0 -25 0 25 50 75 100 125 Figure 4. Reference Voltage vs Temperature Fig.6 UV Lockout Hysteresis vs. Temperature 5 4 UV Lockout Hyteresis(V) Startup Threshold(V) 3 2 1 0 -25 0 25 50 75 100 125 Temperature () Temperature () Figure 5. Start-Up Threshold vs Temperature Figure 6. UV Lockout Hysteresis vs Temperature 7 FAN7527B Typical Performance Characteristics (Continued) Fig.7 Start-up Supply Current vs. Temperature 100 90 80 Fig.8 E.A. Source CurrenT vs. Temperature 0 Start-up Supply Current(uA) -1 70 60 50 40 30 20 10 0 -25 0 25 50 75 100 125 EA Source Current(mA) -2 -3 -4 -5 -25 0 25 50 75 100 125 Temperature () Temperature () Figure 7. Start-Up Supply Current vs Temperature Figure 8. Error Amplifier Source Current vs Temperature Fig.10 E.A. Input Bias Current vs. Temperature 0.5 0.4 Fig.9 E.A. Sink Current vs. Temperature 5 EA Input Bias Current(uA) 4 0.3 0.2 0.1 0.0 -0.1 -0.2 -0.3 -0.4 EA Sink Current(mA) 3 2 1 0 -25 0 25 50 75 100 125 -0.5 -25 0 25 50 75 100 125 Temperature () Temperature () Figure 9. Error Amplifier Sink Current vs Temperature Fig.11 Multiplier Gain vs. Temperature 1.0 Figure 10. Error Amplifier Input Bias Current vs Temperature Fig.12 Idet Threshold Voltage vs. Temperature 4.0 0.6 Idet Threshold Voltage(V) -25 0 25 50 75 100 125 0.8 3.2 Multiplier Gain(1/V) 2.4 0.4 1.6 0.2 0.8 0.0 0.0 -25 0 25 50 75 100 125 Temperature () Temperature () Figure 11. Multiplier Gain vs Temperature Figure 12. ldet Threshold Voltage vs Temperature 8 FAN7527B Typical Performance Characteristics (Continued) Fig.13 Idet Input Hysteresis vs. Temperature 1.0 500 450 0.8 Idet Input Hysteresis(mV) 400 350 300 250 200 150 100 50 0.6 0.4 0.2 0.0 -25 0 25 50 75 100 125 Restart Time(us) 0 -25 0 25 50 75 100 125 Temperature () Temperature() Figure 13. ldet Input Hysteresis vs Temperature Figure 14. Restart Time vs Temperature Fig.15 Max. Mult. Output Voltage vs. temperature 2.0 Fig.16 Supply Current vs. Temperature 5 Maximum Mult. Output Voltage(V) 1.6 4 Supply Current(mA) 1.2 3 0.8 2 0.4 1 0.0 -25 0 25 50 75 100 125 0 -25 0 25 50 75 100 125 Temperature () Temperature () Figure 15. Max.Mult.Output Voltage vs Temperature Figure 16. Supply Current vs Temperature 9 FAN7527B Mechanical Dimensions Package Dimensions in millimeters 8-DIP 1.524 0.10 0.018 0.004 0.060 0.004 0.46 0.10 6.40 0.20 0.252 0.008 ( #1 #8 9.20 0.20 0.362 0.008 9.60 MAX 0.378 #4 #5 2.54 0.100 5.08 MAX 0.200 7.62 0.300 3.40 0.20 0.134 0.008 3.30 0.30 0.130 0.012 0.33 MIN 0.013 0.79 ) 0.031 0.25 -0.05 0~15 +0.10 0.010 -0.002 +0.004 10 FAN7527B Mechanical Dimensions (Continued) Package Dimensions in millimeters 8-SOP MIN 1.55 0.20 0.061 0.008 0.1~0.25 0.004~0.001 #1 #8 4.92 0.20 0.194 0.008 5.13 MAX 0.202 ( #4 #5 6.00 0.30 0.236 0.012 +0.10 0.15 -0.05 +0.004 0.006 -0.002 0.56 ) 0.022 1.80 MAX 0.071 MAX0.10 MAX0.004 3.95 0.20 0.156 0.008 5.72 0.225 0.50 0.20 0.020 0.008 0~ 8 1.27 0.050 0.41 0.10 0.016 0.004 11 FAN7527B Ordering Information Product Number FAN7527BN FAN7527BM Package 8-DIP 8-SOP Operating Temperature -25 ~ +125oC DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 12/21/01 0.0m 001 Stock#DSxxxxxxxx 2001 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. |
Price & Availability of FAN7527B
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |