View 7071_970238.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

74VHCT174A
HEX D-TYPE FLIP FLOP WITH CLEAR
s
s
s
s
s
s
s
s
s s
HIGH SPEED: fMAX = 150 MHz (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4 A (MAX.) at TA=25C COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN.), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 174 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (MAX.)
SOP
TSSOP
ORDER CODES
PACKAGE SOP TSSOP TUBE 74VHCT174AM T&R 74VHCT174AMTR 74VHCT174ATTR
DESCRIPTION The 74VHCT174A is an advanced high-speed CMOS HEX D-TYPE FLIP FLOP WITH CLEAR fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. Information signals applied to D inputs are transferred to the Q outputs on the positive going edge of the clock pulse.
When the CLEAR input is held low, the Q outputs are held low independently of the other inputs. Power down protection is provided on all inputs and outputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V since all inputs are equipped with TTL threshold. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
June 2001
1/10
74VHCT174A
INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
PIN No 1 2, 5, 7, 10, 12, 15 3, 4, 6, 11, 13, 14 9 8 16 SYMBOL CLEAR Q0 to Q5 D0 to D5 CLOCK GND VCC NAME AND FUNCTION Asynchronous Master Reset (Active LOW) Flip-Flop Outputs Data Inputs Clock Input (LOW-to-HIGH, Edge Triggered) Ground (0V) Positive Supply Voltage
TRUTH TABLE
INPUTS CLEAR L H H H
X : Don't Care
OUTPUTS FUNCTION CLOCK X Q L L H Qn NO CHANGE CLEAR
D X L H X
LOGIC DIAGRAM
This logic diagram has not to be used to estimate propagation delays
2/10
74VHCT174A
ABSOLUTE MAXIMUM RATINGS
Symbol VCC VI VO VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage (see note 1) DC Output Voltage (see note 2) DC Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 20 25 50 -65 to +150 300 Unit V V V V mA mA mA mA C C
ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec)
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) VCC = 0V 2) High or Low State
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO VO Top dt/dv Supply Voltage Input Voltage Output Voltage (see note 1) Output Voltage (see note 2) Operating Temperature Input Rise and Fall Time (see note 3) (VCC = 5.0 0.5V) Parameter Value 4.5 to 5.5 0 to 5.5 0 to 5.5 0 to VCC -55 to 125 0 to 20 Unit V V V V C ns/V
1) VCC = 0V 2) High or Low State 3) VIN from 0.8V to 2V
3/10
74VHCT174A
DC SPECIFICATIONS
Test Condition Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 4.5 4.5 4.5 0 to 5.5 5.5 5.5 0 IO=-50 A IO=-8 mA IO=50 A IO=8 mA VI = 5.5V or GND VI = VCC or GND One Input at 3.4V, other input at VCC or GND VOUT = 5.5V TA = 25C Min. 2 0.8 4.4 3.94 0.0 0.1 0.36 0.1 4 1.35 0.5 4.5 4.4 3.8 0.1 0.44 1.0 40 1.5 5.0 Typ. Max. Value -40 to 85C Min. 2 0.8 4.4 3.7 0.1 0.55 1.0 40 1.5 5.0 Max. -55 to 125C Min. 2 0.8 Max. V V V V A A mA A Unit
VIH VIL VOH VOL II ICC
High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current Output Leakage Current
ICC
IOPD
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns)
Test Condition Symbol Parameter VCC (V) 5.0(*) 5.0(*) 5.0(*) 5.0(*) 5.0(*) 5.0(*) CL (pF) 15 50 15 50 TA = 25C Min. Typ. 5.8 6.3 7.6 8.1 Max. 7.8 8.8 10.4 11.4 5.0 5.0 Value -40 to 85C Min. 1.0 1.0 1.0 1.0 Max. 9.0 10.0 13.0 13.0 5.0 5.0 -55 to 125C Min. 1.0 1.0 1.0 1.0 Max. 9.0 10.0 13.0 13.0 5.0 5.0 ns ns ns ns Unit
tPLH tPHL tPHL
tW tW
ts
th
tREM fMAX
Propagation Delay Time CLOCK to Q Propagation Delay Time CLEAR to Q CLEAR Pulse Width LOW CLEAR Pulse Width HIGH or LOW Setup Time D to CLOCK, HIGH or LOW Hold Time D to CLOCK, HIGH or LOW Recovery Time CLEAR to CLOCK Maximum Clock Frequency
5.0(*)
5.0
6.0
6.0
ns
5.0(*) 5.0(*) 5.0(*) 5.0
(*)
0.0 3.0 15 50 95 55 150 85 80 50
0.0 3.0 80 50
0.0 3.0
ns ns MHz
(*) Voltage range is 5.0V 0.5V
4/10
74VHCT174A
CAPACITIVE CHARACTERISTICS
Test Condition Symbol Parameter Min. CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) TA = 25C Typ. 6 28 Max. 10 Value -40 to 85C Min. Max. 10 -55 to 125C Min. Max. 10 pF pF Unit
1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per flip-flop)
DYNAMIC SWITCHING CHARACTERISTICS
Test Condition Symbol Parameter VCC (V) 5.0 TA = 25C Min. Typ. 0.3 -0.8 CL = 50 pF 2.0 -0.3 V Max. 0.8 Value -40 to 85C Min. Max. -55 to 125C Min. Max. Unit
VOLP VOLV VIHD
VILD
Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3)
5.0
5.0
0.8
1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.0V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.0V. Inputs under test switching: 3.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz.
TEST CIRCUIT
CL =15/50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50)
5/10
74VHCT174A
WAVEFORM 1: PROPAGATION DELAYS, SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle)
WAVEFORM 2: PROPAGATION DELAYS (f=1MHz; 50% duty cycle)
6/10
74VHCT174A
WAVEFORM 3: REMOVAL TIME (f=1MHz; 50% duty cycle)
7/10
74VHCT174A
SO-16 MECHANICAL DATA
DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8 (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45 (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010
PO13H
8/10
74VHCT174A
TSSOP16 MECHANICAL DATA
mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8 0.75 0 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch
A
A2 A1 b e K c L E
D
E1
PIN 1 IDENTIFICATION
1
0080338D
9/10
74VHCT174A
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom (c) http://www.st.com
10/10

▲Up To Search▲

Price & Availability of 7071

	To Download 7071 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .