View 2684_965252.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Bulletin I25157 rev. C 04/00
ST300C..C SERIES
PHASE CONTROL THYRISTORS Hockey Puk Version
Features
Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (E-PUK)
650A
Typical Applications
DC motor controls Controlled DC power supplies AC controllers
Major Ratings and Characteristics
Parameters
IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I 2t @ 50Hz @ 60Hz V DRM/V RRM tq TJ typical
case style TO-200AB (E-PUK)
Units
A C A C A A KA2s KA2s V s C
ST300C..C
650 55 1290 25 8000 8380 320 292 400 to 2000 100 - 40 to 125
www.irf.com
1
ST300C..C Series
Bulletin I25157 rev. C 04/00
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code
04 08 12 ST300C..C 16 18 20
V DRM/V RRM, max. repetitive peak and off-state voltage V
400 800 1200 1600 1800 2000
VRSM , maximum nonrepetitive peak voltage V
500 900 1300 1700 1900 2100
I DRM/I RRM max.
@ TJ = TJ max
mA
50
On-state Conduction
Parameter
IT(AV) Max. average on-state current @ Heatsink temperature IT(RMS) Max. RMS on-state current ITSM Max. peak, one-cycle non-repetitive surge current
ST300C..C
650 (320) 55 (75) 1290 8000 8380 6730 7040
Units Conditions
A C 180 conduction, half sine wave double side (single side) cooled DC @ 25C heatsink temperature double side cooled t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms KA s
2
No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max.
It
2
Maximum I t for fusing
2
320 292 226 207
t = 8.3ms t = 10ms t = 8.3ms
I2 t
Maximum I2t for fusing
3200 0.97
KA2s
t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max.
V T(TO)1 Low level value of threshold voltage V T(TO)2 High level value of threshold voltage r t1 r t2 VTM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Typical latching current
V 0.98 (I > x IT(AV)),TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV)), T J = TJ max. m 0.73 2.18 600 1000 mA T J = 25C, anode supply 12V resistive load V (I > x IT(AV)),TJ = TJ max. I = 1635A, TJ = TJ max, t = 10ms sine pulse
pk p
0.74
2
www.irf.com
ST300C..C Series
Bulletin I25157 rev. C 04/00
Switching
Parameter
di/dt Max. non-repetitive rate of rise of turned-on current td t
q
ST300C..C
1000 1.0
Units Conditions
A/s Gate drive 20V, 20, t 1s T J = TJ max, anode voltage 80% VDRM Gate current 1A, di /dt = 1A/s
g r
Typical delay time Typical turn-off time
s 100
V = 0.67% VDRM, TJ = 25C
d
ITM = 300A, T J = TJ max, di/dt = 40A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, tp = 500s
Blocking
Parameter
dv/dt IRRM IDRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current
ST300C..C
500 50
Units Conditions
V/s mA TJ = TJ max, linear to 80% rated VDRM TJ = TJ max, rated V DRM/V RRM applied
Triggering
Parameter
PGM Maximum peak gate power
ST300C..C
10.0 2.0 3.0 20
Units Conditions
W A T J = TJ max, tp 5ms T J = TJ max, f = 50Hz, d% = 50 T J = TJ max, tp 5ms
PG(AV) Maximum average gate power IGM +VGM -V GM Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. 200 IGT DC gate current required to trigger 100 50 2.5 VGT DC gate voltage required to trigger IGD VGD DC gate current not to trigger DC gate voltage not to trigger 1.8 1.1
V 5.0 MAX. 200 3.0 10.0 0.25 mA V V mA
TJ = TJ max, t 5ms
p
T J = - 40C T J = 25C T J = 125C T J = - 40C T J = 25C T J = 125C Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied
TJ = TJ max
www.irf.com
3
ST300C..C Series
Bulletin I25157 rev. C 04/00
Thermal and Mechanical Specification
Parameter
TJ Tstg Max. operating temperature range Max. storage temperature range
ST300C..C
-40 to 125 -40 to 150 0.09 0.04 0.02 0.01 9800 (1000)
Units
C
Conditions
RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, case to heatsink F Mounting force, 10%
DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled
K/W N (Kg) g
wt
Approximate weight Case style
83
TO - 200AB (E-PUK)
See Outline Table
RthJ-hs Conduction
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
Conduction angle
180 120 90 60 30
Sinusoidal conduction
Single Side Double Side 0.010 0.012 0.015 0.022 0.036 0.011 0.012 0.015 0.022 0.036
Rectangular conduction
Single Side Double Side 0.007 0.012 0.016 0.023 0.036 0.007 0.013 0.017 0.023 0.037
Units
Conditions
TJ = TJ max.
K/W
Ordering Information Table
Device Code
ST
1 1 2 3 4 5 6 7 Thyristor Essential part number 0 = Converter grade C = Ceramic Puk
30
2
0
3
C
4
20
5
C
6
1
7 8
Voltage code: Code x 100 = VRRM (See Voltage Rating Table) C = Puk Case TO-200AB (E-PUK) 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8
-
Critical dv/dt: None = 500V/sec (Standard value) L = 1000V/sec (Special selection)
4
www.irf.com
ST300C..C Series
Bulletin I25157 rev. C 04/00
Outline Table
ANODE TO GATE CREEPAGE DISTANCE: 11.18 (0.44) MIN. STRIKE DISTANCE: 7.62 (0.30) MIN. 25.3 (0.99) DIA. MAX. 0.3 (0.01) MIN.
14.1 / 15.1 (0.56 / 0.59) 0.3 (0.01) MIN. 25.3 (0.99) DIA. MAX. 40.5 (1.59) DIA. MAX. GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE
2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19)
Case Style TO-200AB (E-PUK)
All dimensions in millimeters (inches)
25 5
Quote between upper and lower pole pieces has to be considered after application of Mounting Force (see Thermal and Mechanical Specification)
42 (1.65) MAX. 28 (1.10)
Maximum Allowable Heatsink Temperature (C)
130 120 110 100 90 80 70 60 50 40 30 0 100
30
Maximum Allowable Heatsink Temperature (C)
ST300C..C Series (Single Side Cooled) R thJ-hs (DC) = 0.09 K/W
130 120 110 100 90 80 70 60 50 40 30 20 0 200 400
30 60 90 120
Conduction Period
ST300C..C Series (Single Side Cooled) R thJ-hs (DC) = 0.09 K/W
Conduction Angle
60
90
120
180
180
DC
200
300
400
500
600
800
Average On-state Current (A)
Fig. 1 - Current Ratings Characteristics
Average On-state Current (A)
Fig. 2 - Current Ratings Characteristics
www.irf.com
5
ST300C..C Series
Bulletin I25157 rev. C 04/00
Maximum Allowable Heatsink Temperature (C) Maximum Allowable Heatsink Temperature (C)
130 120 110 100 90 80 70 60 50 40 30 20 10 0
ST300C..C Series (Double Side Cooled) R thJ-hs (DC) = 0.04 K/W
130 120 110 100 90 80 70 60 50 40 30 20 0
30 60
ST300C..C Series (Double Side Cooled) R thJ-hs (DC) = 0.04 K/W
Conduction Angle
Conduction Period
30
90 120 180 DC
60
90
120 180
200
400
600
800
1000
200 400 600 800 1000 1200 1400
Average On-state Current (A)
Fig. 4 - Current Ratings Characteristics
Average On-state Current (A)
Fig. 3 - Current Ratings Characteristics
Maximum Average On-state Power Loss (W)
Maximum Average On-state Power Loss (W)
1600 1400 1200 1000 800 600 400 200 0 0
180 120 90 60 30
RMS Limit
1800 1600 1400 1200 1000 800 600 400 200 0 0
DC 180 120 90 60 30
RMS Limit
Conduction Period ST300C..C Series T J = 125C
Conduction Angle
ST300C..C Series T J = 125C
100 200 300 400 500 600 700
Average On-state Current (A)
200
400
600
800 1000 1200
Average On-state Current (A)
Fig. 6- On-state Power Loss Characteristics
Fig. 5- On-state Power Loss Characteristics
Peak Half Sine Wave On-state Current (A)
Peak Half Sine Wave On-state Current (A)
7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 1
At Any Rated Load Condition And With Rated V RRM Applied Following Surge. Initial T J 125C = @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s
8000 7500 7000 6500 6000 5500 5000 4500 4000 3500
Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial T J 125C = No Voltage Reapplied Rated V RRM Reapplied
ST300C..C Series
ST300C..C Series
10
100
3000 0.01
0.1
Pulse Train Duration (s)
1
Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled
Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled
6
www.irf.com
ST300C..C Series
Bulletin I25157 rev. C 04/00
10000
Instantaneous On-state Current (A)
T = 25C
J
TJ = 125C
1000
ST300C..C Series
100 0 1 2 3 4 5 6 7 8 9
Instantaneous On-state Voltage (V)
Fig. 9 - On-state Voltage Drop Characteristics
Transient Thermal Impedance Z thJ-hs (K/W)
0.1
Steady State Value R thJ-hs = 0.09 K/W (Single Side Cooled) R thJ-hs = 0.04 K/W (Double Side Cooled) (DC Operation)
0.01
ST300C..C Series
0.001 0.001
0.01
0.1
Square Wave Pulse Duration (s)
1
10
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
100
Instantaneous Gate Voltage (V)
Rectangular gate pulse a) Recommended load line for rated di/dt : 20V, 10ohms; tr<=1 s b) Recommended load line for <=30% rated di/dt : 10V, 10ohms 10 tr<=1 s
(1) PGM = 10W, (2) PGM = 20W, (3) PGM = 40W, (4) PGM = 60W,
tp = 4ms tp = 2ms tp = 1ms tp = 0.66ms
(a) (b)
Tj=-40 C Tj=25 C
Tj=125 C
1 VGD IGD 0.1 0.001 0.01
(1)
(2) (3) (4)
Device: ST300C..C Series
Frequency Limited by PG(AV)
0.1 1 Instantaneous Gate Current (A)
Fig. 11 - Gate Characteristics
10
100
www.irf.com
7

▲Up To Search▲

Price & Availability of 2684

	To Download 2684 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .