 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Bulletin I25160 rev. C 02/00 ST280CH..C SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (A-PUK) Extended temperature range 500A Typical Applications DC motor controls Controlled DC power supplies AC controllers Major Ratings and Characteristics Parameters IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I 2t @ 50Hz @ 60Hz V DRM/V RRM tq TJ typical case style TO-200AB (A-PUK) Units A C A C A A KA2s KA2s V s C ST280CH..C 500 80 1130 25 7200 7500 260 230 400 to 600 100 - 40 to 150 www.irf.com 1 ST280CH..C Series Bulletin I25160 rev. C 02/00 ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage Type number Code 04 ST280CH..C 06 V DRM/V RRM, max. repetitive peak and off-state voltage V 400 600 VRSM , maximum nonrepetitive peak voltage V 500 700 I DRM /I RRM max. @ TJ = TJ max mA 75 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one-cycle non-repetitive surge current ST280CH..C 500 (185) 80 (110) 1130 7200 7500 6000 6300 Units Conditions A C 180 conduction, half sine wave double side (single side) cooled DC @ 25C heatsink temperature double side cooled t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms KA2s t = 8.3ms t = 10ms t = 8.3ms KA2s No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max. I 2t Maximum I2t for fusing 260 235 180 165 I 2 t Maximum I2t for fusing 2600 0.84 t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. V T(TO) 1 Low level value of threshold voltage V T(TO) 2 High level value of threshold voltage r t1 r t2 V TM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Max (typical) latching current V 0.88 (I > x IT(AV)),TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. m 0.47 1.35 600 mA 1000 (300) T J = 25 C, anode supply 12V resistive load V (I > x IT(AV)),TJ = TJ max. I = 1000A, TJ = TJ max, t = 10ms sine pulse pk p 0.50 Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current t d ST280CH..C 1000 1.0 Units Conditions A/s Gate drive 20V, 20, t 1s TJ = T J max, anode voltage 80% VDRM Gate current 1A, di /dt = 1A/s g r Typical delay time Typical turn-off time s tq 100 V = 0.67% VDRM, TJ = 25C d ITM = 300A, TJ = T J max, di/dt = 20A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, t = 500s p 2 www.irf.com ST280CH..C Series Bulletin I25160 rev. C 02/00 Blocking Parameter dv/dt IDRM IRRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current ST280CH..C 500 75 Units Conditions V/s mA T J = TJ max. linear to 80% rated V DRM TJ = TJ max, rated VDRM /V RRM applied Triggering Parameter PGM Maximum peak gate power ST280CH..C 10.0 2.0 3.0 20 Units Conditions W A TJ = TJ max, tp 5ms TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, tp 5ms PG(AV) Maximum average gate power IGM Max. peak positive gate current +VGM Maximum peak positive gate voltage -VGM Maximum peak negative gate voltage TYP. 180 IGT DC gate current required to trigger 90 30 2.9 VGT DC gate voltage required to trigger IGD VGD DC gate current not to trigger DC gate voltage not to trigger 1.8 1.0 V 5.0 MAX. 150 3.0 10 0.30 mA V V mA T J = TJ max, t 5ms p TJ = - 40C TJ = 25C TJ = 150C TJ = - 40C TJ = 25C TJ = 150C Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = TJ max Thermal and Mechanical Specification Parameter TJ Tstg Max. operating temperature range Max. storage temperature range ST280CH..C -40 to 150 -40 to 150 0.17 0.08 0.033 0.017 4900 (500) Units C Conditions RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, case to heatsink F Mounting force, 10% DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled K/W N (Kg) g wt Approximate weight Case style 50 TO - 200AB (A-PUK) See Outline Table www.irf.com 3 ST280CH..C Series Bulletin I25160 rev. C 02/00 RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle 180 120 90 60 30 Sinusoidal conduction Single Side Double Side 0.016 0.019 0.024 0.035 0.060 0.017 0.019 0.024 0.035 0.060 Rectangular conduction Single Side Double Side 0.011 0.019 0.026 0.036 0.060 0.011 0.019 0.026 0.037 0.061 Units Conditions T J = TJ max. K/W Ordering Information Table Device Code ST 1 28 2 0 3 CH 4 06 5 C 6 1 7 8 1 2 3 4 5 6 7 - Thyristor Essential part number 0 = Converter grade CH = Ceramic Puk, High temperature Voltage code: Code x 100 = VRRM (See Voltage Rating Table) C = Puk Case TO-200AB (A-PUK) 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/sec (Standard selection) L = 1000V/sec (Special selection) 4 www.irf.com ST280CH..C Series Bulletin I25160 rev. C 02/00 Outline Table ANODE TO GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. 19 (0.75) DIA. MAX. 0.3 (0.01) MIN. 13.7 / 14.4 (0.54 / 0.57) 0.3 (0.01) MIN. 19 (0.75) DIA. MAX. 38 (1.50) DIA MAX. GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE 2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19) 25 5 Case Style TO-200AB (A-PUK) All dimensions in millimeters (inches) Quote between upper and lower pole pieces has to be considered after application of Mounting Force (see Thermal and Mechanical Specification) 42 (1.65) MAX. 28 (1.10) Maximum Allowable Heatsink Temperature (C) Maximum Allowable Heatsink Temperature (C) 150 140 130 120 110 100 90 80 70 60 50 40 0 100 30 ST280CH..C Series (Single Side Cooled) R thJ-hs (DC) = 0.17 K/W Conduction Angle 60 90 120 180 150 140 130 120 110 100 90 80 70 60 50 40 30 20 0 ST280CH..C Series (Single Side Cooled) R thJ-hs (DC) = 0.17 K/W Conduction Period 30 60 90 120 180 DC 200 300 400 500 100 200 300 400 500 600 700 Average On-state Current (A) Fig. 2 - Current Ratings Characteristics Average On-state Current (A) Fig. 1 - Current Ratings Characteristics www.irf.com 5 ST280C..H Series Bulletin I25160 rev. C 02/00 Maximum Allowable Heatsink Temperature (C) Maximum Allowable Heatsink Temperature (C) 150 140 130 120 110 100 90 80 70 60 50 40 30 20 ST280CH..C Series (Double Side Cooled) R thJ-hs(DC) = 0.08 K/W Conduction Angle 30 60 90 120 180 150 140 130 120 110 100 90 80 70 60 50 40 30 20 0 ST280CH..C Series (Double Side Cooled) R thJ-hs (DC) = 0.08 K/W Conduction Period 30 60 90 120 180 DC 0 100 200 300 400 500 600 700 800 Average On-state Current (A) Fig. 3 - Current Ratings Characteristics 200 400 600 800 1000 1200 Average On-state Current (A) Fig. 4 - Current Ratings Characteristics Maximum Average On-state Power Loss (W) 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 Maximum Average On-state Power Loss (W) 1800 1600 1400 1200 1000 800 600 400 200 0 0 180 120 90 60 30 RMS Limit DC 180 120 90 60 30 RMS Limit Conduction Angle ST280CH..C Series T J = 150C Conduction Period ST280CH..C Series T J = 150C 0 100 200 300 400 500 600 700 800 Average On-state Current (A) Fig. 5- On-state Power Loss Characteristics 200 400 600 800 1000 1200 Average On-state Current (A) Fig. 6- On-state Power Loss Characteristics Peak Half Sine Wave On-state Current (A) 6500 6000 5500 5000 4500 4000 3500 Peak Half Sine Wave On-state Current (A) At Any Rated Load Condition And With Rated V RRM Applied Following Surge. Initial T J= 150C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial T J 150C = No Voltage Reapplied Rated V Reapplied RRM ST280CH..C Series ST280CH..C Series 3000 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled 2500 0.01 0.1 Pulse Train Duration (s) 1 Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled 6 www.irf.com ST280C..H Series Bulletin I25160 rev. C 02/00 Instantaneous On-state Current (A) Instantaneous On-state Voltage (V) Fig. 9 - On-state Voltage Drop Characteristics Transient Thermal Impedance Z thJ-hs (K/W) Square Wave Pulse Duration (s) Fig. 10 - Thermal Impedance ZthJ-hs Characteristics Instantaneous Gate Voltage (V) Instantaneous Gate Current (A) Fig. 11 - Gate Characteristics www.irf.com 7 |
Price & Availability of 2682
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |