Part Number Hot Search : 
LUG2040 2SB1731 B45192ER MA3200W 045CT FM107 400AC CY621
Product Description
Full Text Search
 

To Download EVAL-ADF4154EB1 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Fractional-N Frequency Synthesizer ADF4154
FEATURES
RF bandwidth 500 MHz to 4 GHz 2.7 V to 3.3 V power supply Separate VP allows extended tuning voltage Programmable dual-modulus prescaler 4/5, 8/9 Programmable charge pump currents 3-wire serial interface Digital lock detect Power-down mode Pin compatible with the ADF4110/ADF4111/ ADF4112/ADF4113, ADF4106 and ADF4153 Programmable modulus on fractional-N synthesizer Trade-off noise versus spurious performance Fast-lock mode with built-in timer
GENERAL DESCRIPTION
The ADF4154 is a fractional-N frequency synthesizer that implements local oscillators in the up conversion and down conversion sections of wireless receivers and transmitters. It consists of a low noise digital phase frequency detector (PFD), a precision charge pump, and a programmable reference divider. There is a - based fractional interpolator to allow programmable fractional-N division. The INT, FRAC, and MOD registers define an overall N divider (N = (INT + (FRAC/MOD))). In addition, the 4-bit reference counter (R counter) allows selectable REFIN frequencies at the PFD input. A complete phase-locked loop (PLL) can be implemented if the synthesizer is used with an external loop filter and a voltage controlled oscillator (VCO). A key feature of the ADF4154 is the fast-lock mode with a builtin timer. The user can program a predetermined count-down time value so that the PLL will remain in wide bandwidth mode, instead of having to control this time externally. Control of all on-chip registers is via a simple 3-wire interface. The device operates with a power supply ranging from 2.7 V to 3.3 V, and can be powered down when not in use.
AVDD DVDD VP SDVDD RSET
APPLICATIONS
CATV equipment Base stations for mobile radio (GSM, PCS, DCS, CDMA, WCDMA) Wireless handsets (GSM, PCS, DCS, CDMA, WCDMA) Wireless LANs Communications test equipment
FUNCTIONAL BLOCK DIAGRAM
REFERENCE 4-BIT R COUNTER +
REFIN
x2 DOUBLER VDD DGND
PHASE FREQUENCY DETECTOR -
CHARGE PUMP
CP
HIGH Z
LOCK DETECT MUXOUT OUTPUT MUX VDD RDIV NDIV THIRD ORDER FRACTIONAL INTERPOLATOR FRACTION REG MODULUS REG FAST-LOCK SWITCH
CURRENT SETTING
RFCP3 RFCP2 RFCP1 N COUNTER RFINA RFINB
CLOCK DATA LE
24-BIT DATA REGISTER
INTEGER REG P = 4/5 OR 8/9 B = 9 BITS; A = 3 BITS
AGND
DGND
CPGND
Figure 1. Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. www.analog.com Tel: 781.329.4700 Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
04833-0-001
ADF4154
ADF4154 TABLE OF CONTENTS
Specifications..................................................................................... 3 Timing Characteristics..................................................................... 4 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Pin Configuration and Pin Function Descriptions...................... 6 Typical Performance Characteristics ............................................. 7 Circuit Description........................................................................... 9 Reference Input Section............................................................... 9 RF Input Stage............................................................................... 9 RF INT Divider............................................................................. 9 INT, FRAC, MOD, and R Relationship...................................... 9 RF R Counter ................................................................................ 9 Phase Frequency Detector (PFD) and Charge Pump.............. 9 MUXOUT and Lock Detect...................................................... 10 Input Shift Registers ................................................................... 10 Program Modes .......................................................................... 10 Registers ........................................................................................... 11 Register Definition ..................................................................... 15 R-Divider Register, R1 ............................................................... 15 Control Register, R2 ................................................................... 15 Noise and Spur Register, R3 ...................................................... 16 Reserved Bits............................................................................... 16 RF Synthesizer: A Worked Example ........................................ 16 Modulus....................................................................................... 17 Reference Doubler and Reference Divider ............................. 17 12-Bit Programmable Modulus................................................ 17 Spurious Optimization and Fast-lock...................................... 17 Fast-Lock Timer and Register Sequences ............................... 17 Fast-Lock: A Worked Example ................................................. 18 Fast-Lock: Loop Filter Topology .............................................. 18 Spurious Signals.......................................................................... 18 Filter Design--ADIsimPLL....................................................... 18 Interfacing ................................................................................... 18 PCB Design Guidelines for Chip Scale Package .................... 19 Outline Dimensions ....................................................................... 20 Ordering Guide .......................................................................... 20
Rev. 0 | Page 2 of 20
ADF4154 SPECIFICATIONS
Table 1. AVDD = DVDD = SDVDD = 2.7 V to 3.3 V; VP = AVDD to 5.5 V; AGND = DGND = 0 V; TA = TMIN to TMAX, unless otherwise noted; dBm referred to 50 . The operating temperature for the B version is -40C to +80C.
Parameter
RF CHARACTERISTICS (3 V) RF Input Frequency (RFIN)1 REFERENCE CHARACTERISTICS REFIN Input Frequency1 REFIN Input Sensitivity
B Version
0.5/4.0 1.0/4.0 10/250 0.7/AVDD 0 to AVDD 10 100 32
Unit
GHz min/max GHz min/max MHz min/max V p-p min/max V max pF max A max MHz max
Test Conditions/Comments
See Figure 18 for input circuit. -8 dBm/0 dBm min/max. For lower frequencies, ensure slew rate > 396 V/s. -10 dBm/0 dBm min/max. See Figure 17 for input circuit.
For f < 10 MHz, use a dc-coupled, CMOS compatible square wave, slew rate > 21 V/s.
AC-coupled. CMOS compatible.
REFIN Input Capacitance REFIN Input Current PHASE DETECTOR Phase Detector Frequency2 CHARGE PUMP ICP Sink/Source High Value Low Value Absolute Accuracy RSET Range ICP Three-State Leakage Current Matching ICP vs. VCP ICP vs. Temperature LOGIC INPUTS VINH, Input High Voltage VINL, Input Low Voltage IINH/IINL, Input Current CIN, Input Capacitance LOGIC OUTPUTS VOH, Output High Voltage VOL, Output Low Voltage POWER SUPPLIES AVDD DVDD, SDVDD VP IDD3 Low Power Sleep Mode NOISE CHARACTERISTICS Phase Noise Figure of Merit4 ADF4154 Phase Noise Floor5 Phase Noise Performance6 1750 MHz Output7
5 312.5 2.5 1.5/10 1 2 2 2 1.4 0.6 1 10 1.4 0.4 2.7/3.3 AVDD AVDD/5.5 24 1 -213 -143 -139 -102
mA typ A typ % typ k min/max nA typ % typ % typ % typ V min V max A max pF max V min V max V min/V max V min/V max mA max A typ dBc/Hz typ dBc/Hz typ dBc/Hz typ dBc/Hz typ
Programmable. See Table 5. With RSET = 5.1 k. With RSET = 5.1 k. Sink and source current. 0.5 V < VCP < VP - 0.5. 0.5 V < VCP < VP - 0.5. VCP = VP/2.
Open-drain 1 k pull-up to 1.8 V. IOL = 500 A.
20 mA typical.
@ 10 MHz PFD frequency. @ 26 MHz PFD frequency. @ VCO output. @ 1 kHz offset, 26 MHz PFD frequency.
1 2
Use a square wave for frequencies below fMIN. Guaranteed by design. Sample tested to ensure compliance. 3 AC coupling ensures AVDD/2 bias. See Figure 17 for typical circuit. 4 This figure can be used to calculate phase noise for any application. Use the formula -213 + 10log(fPFD) + 20logN to calculate in-band phase noise performance, as seen at the VCO output. The value given is the lowest noise mode. 5 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20logN (where N is the N-divider value). The value given is the lowest noise mode. 6 The phase noise is measured with the EVAL-ADF4154EB1 evaluation board and the HP8562E spectrum analyzer. 7 fREFIN = 26 MHz; fPFD = 26 MHz; offset frequency = 1 kHz; RFOUT = 1750 MHz; loop B/W = 20 kHz; lowest noise mode. Rev. 0 | Page 3 of 20
ADF4154 TIMING CHARACTERISTICS
Table 2. AVDD = DVDD = SDVDD = 2.7 V to 3.3 V; VP = AVDD to 5.5 V; AGND = DGND = 0 V; TA = TMIN to TMAX, unless otherwise noted; dBm referred to 50 .
Parameter1 t1 t2 t3 t4 t5 t6 t7 Limit at TMIN to TMAX (B Version) 20 10 10 25 25 10 20 Unit ns min ns min ns min ns min ns min ns min ns min Test Conditions/Comments LE Setup Time DATA to CLOCK Setup Time DATA to CLOCK Hold Time CLOCK High Duration CLOCK Low Duration CLOCK to LE Setup Time LE Pulse Width
1
Guaranteed by design, but not production tested.
t4
CLOCK
t5
t2
DATA DB23 (MSB) DB22
t3
DB2 DB1 (CONTROL BIT C2) DB0 (LSB) (CONTROL BIT C1)
t7
LE
t1
LE
t6
04833-0-026
Figure 2. Timing Diagram
Rev. 0 | Page 4 of 20
ADF4154 ABSOLUTE MAXIMUM RATINGS
Table 3. Absolute Maximum Ratings.1, 2, 3 TA = 25C, unless otherwise noted.
Parameter VDD to GND VDD to VDD VP to GND VP to VDD Digital I/O Voltage to GND Analog I/O Voltage to GND REFIN, RFIN to GND Operating Temperature Range Industrial (B Version) Storage Temperature Range Maximum Junction Temperature TSSOP JA Thermal Impedance LFCSP JA Thermal Impedance (Paddle Soldered) LFCSP JA Thermal Impedance (Paddle Not Soldered) Lead Temperature, Soldering Vapor Phase (60 sec) Infrared Rating -0.3 V to +4 V -0.3 V to +0.3 V -0.3 V to +5.8 V -0.3 V to +5.8 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -40C to +85C -65C to +150C 150C 150.4C/W 122C/W 216C/W
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
1
This device is a high performance RF integrated circuit with an ESD rating of < 2 kV, and it is ESD sensitive. Proper precautions should be taken for handling and assembly. 2 GND = AGND = DGND = 0 V. 3 VDD = AVDD = DVDD = SDVDD.
215C 220C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 5 of 20
ADF4154 PIN CONFIGURATION AND PIN FUNCTION DESCRIPTIONS
RSET 1 CP 2 CPGND 3 AGND 4
16 15 14
VP DVDD MUXOUT
LE TOP VIEW RFINB 5 (Not to Scale) 12 DATA 11 CLK RFINA 6
13
ADF4154
20 CP 19 RSET 18 VP 17 DVDD 16 DVDD
04833-0-002
AVDD 7 REFIN 8
10 9
SDVDD DGND
CPGND AGND AGND RFINB RFINA
1 2 3 4 5
PIN 1 INDICATOR
ADF4154
TOP VIEW
15 MUXOUT 14 LE 13 DATA 12 CLK 11 SDVDD
AVDD 6 AVDD 7 REFIN 8 DGND 9 DGND 10
Figure 3. TSSOP Pin Configuration
Figure 4. LFCSP Pin Configuration
Table 4. Pin Function Descriptions
TSSOP 1 LFCSP 19 Mnemonic RSET Description Connecting a resistor between this pin and ground sets the maximum charge pump output current. The relationship between ICP and RSET is
I CP max =
25.5 RSET
2 3 4 5 6 7
20 1 2, 3 4 5 6, 7
CP CPGND AGND RFINB RFINA AVDD
8
8
REFIN
9 10 11 12 13 14 15
9, 10 11 12 13 14 15 16, 17
DGND SDVDD CLK DATA LE MUXOUT DVDD
16
18
VP
where RSET = 5.1 k and ICPmax = 5 mA. Charge Pump Output. When enabled, this provides ICP to the external loop filter, which in turn drives the external VCO. Charge Pump Ground. This is the ground return path for the charge pump. Analog Ground. This is the ground return path of the prescaler. Complementary Input to the RF Prescaler. This point should be decoupled to the ground plane with a small bypass capacitor, typically 100 pF (see Figure 18). Input to the RF Prescaler. This small-signal input is normally ac-coupled from the VCO. Positive Power Supply for the RF Section. Decoupling capacitors to the digital ground plane should be placed as close as possible to this pin. AVDD has a value of 3 V 10%. AVDD must have the same voltage as DVDD. Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and an equivalent input resistance of 100 k (see Figure 17). This input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled. Digital Ground. - Power. Decoupling capacitors to the digital ground plane should be placed as close as possible to this pin. SDVDD has a value of 3 V 10%. SDVDD must have the same voltage as DVDD. Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into the shift register on the CLK rising edge. This input is a high impedance CMOS input. Serial Data Input. The serial data is loaded MSB first with the two LSBs as the control bits. This input is a high impedance CMOS input. Load Enable, CMOS Input. When LE is high, the data stored in the shift registers is loaded into one of the four latches, the latch being selected using the control bits. This multiplexer output allows either the RF lock detect, the scaled RF, or the scaled reference frequency to be accessed externally. Positive Power Supply for the Digital Section. Decoupling capacitors to the digital ground plane should be placed as close as possible to this pin. DVDD has a value of 3 V 10%. DVDD must have the same voltage as AVDD. Charge Pump Power Supply. This should be greater than or equal to VDD. In systems where VDD is 3 V, it can be set to 5.5 V and used to drive a VCO with a tuning range of up to 5.5 V.
Rev. 0 | Page 6 of 20
04833-0-003
ADF4154 TYPICAL PERFORMANCE CHARACTERISTICS
Figure 5 to Figure 10, and Figure 12: RFOUT = 1.722 GHz, PFD Frequency = 26 MHz, INT = 66, Channel Spacing = 200 kHz, Modulus = 130, Fraction = 30/130, and ICP = 5 mA. Loop Bandwidth = 20 kHz, Reference = 26 MHz, VCO = Vari-L VCO190-1750T, Evaluation Board = EVAL-ADF4154EB1. Measurements were taken on the HP8562E spectrum analyzer.
0 -10 -20
OUTPUT POWER (dB)
0 VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOWEST NOISE MODE N = 66 30/130 RBW = 10Hz -10 -20
OUTPUT POWER (dB)
REFERENCE LEVEL = -4dBm
REFERENCE LEVEL = -4.2dBm
-30 -40 -50 -60 -70
-30 -40 -50 -60 -70 -80 -71dBc@200kHz
VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOWEST NOISE MODE N = 66 30/130 RBW = 10Hz
-102dBc/Hz -80
04833-0-004
-100 -2kHz -1kHz 1.722GHz 1kHz 2kHz
-100 -400kHz -200kHz 1.722GHz 200kHz 400kHz
Figure 5. Phase Noise (Lowest Noise Mode)
0 -10 -20
OUTPUT POWER (dB)
Figure 8. Spurs (Lowest Noise Mode)
0 VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOW NOISE AND SPUR MODE N = 66 30/130 RBW = 10Hz
REFERENCE LEVEL = -4.2dBm
-30 -40 -50 -60
OUTPUT POWER (dB)
VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOW NOISE AND SPUR MODE N = 66 30/130 RBW = 10Hz
-10 -20 -30 -40 -74dBc@200kHz -50 -60 -70 -80
04833-0-005
REFERENCE LEVEL = -4.2dBm
-95dBc/Hz -70 -80
-90
-100
-100 -400kHz -200kHz 1.722GHz 200kHz 400kHz
-2kHz
-1kHz
1.722GHz
1kHz
2kHz
Figure 6. Phase Noise (Low Noise Mode and Spur Mode)
0 -10 -20
OUTPUT POWER (dB)
Figure 9. Spurs (Low Noise and Spur Mode)
0 VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOWEST SPUR NOISE N = 66 30/130 RBW = 10Hz
REFERENCE LEVEL = -4.2dBm
-30 -40 -50 -60 -70 -80
OUTPUT POWER (dB)
VDD = 3V, VP = 5V ICP = 5mA PFD FREQUENCY = 26MHz CHANNEL STEP = 200kHz LOOP BANDWIDTH = 20kHz LOWEST SPUR MODE N = 66 30/130 RBW = 10Hz
-10 -20 -30 -40 -50 -60 -70 -80
04833-0-006
REFERENCE LEVEL = -4.2dBm
-90dBc/Hz
-100 -2kHz -1kHz 1.722GHz 1kHz 2kHz
-100 -400kHz -200kHz 1.722GHz 200kHz 400kHz
Figure 7. Phase Noise (Lowest Spur Mode)
Figure 10. Spurs (Lowest Spur Mode)
Rev. 0 | Page 7 of 20
04833-0-009
-90
-90
04833-0-008
-90
04833-0-007
-90
-90
ADF4154
-130
-80
-85
PHASE NOISE (dBc/Hz)
PHASE NOISE (dBc/Hz)
-140
-90
-150
-95
-100
-160
-105
04833-0-013
04833-0-028
04833-0-014
-170 100
04833-0-010
1000
10000
100000
-110
0
5
10
PHASE DETECTOR FREQUENCY (kHz)
15 20 RSET VALUE (k)
25
30
35
Figure 11. PFD Noise Floor vs. PFD Frequency (Lowest Noise Mode)
5 0
Figure 14. Phase Noise vs. RSET
-90 -92
-5
PHASE NOISE (dBc/Hz)
AMPLITUDE (dBm)
-94 -96
-10 -15 -20 -25 -30 -35
P = 4/5
-98 -100
P = 8/9
04833-0-011
-102
4.0 4.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
FREQUENCY (GHz)
-104 -60
-40
-20
0 20 40 TEMPERATURE(C)
60
80
100
Figure 12. RF Input Sensitivity Figure 15. Phase Noise vs. Temperature
6 5 4 3
1.700 1.696 1.692 1.688 1.684
FREQUENCY (GHz)
2 1
ICP(mA)
1.680 1.676 1.672 1.668 1.664 1.660 1.656 1.652 1.648 1.644 1.640 0
A B
0 -1 -2 -3 -4 -5 -6 0 1 2 VCP(V) 3 4 5
04833-0-012
10
20
30
40
50 60 TIME (s)
65
75
85
95
100
Figure 13. Charge Pump Output Characteristics
Figure 16. A) Lock Time in Fast-lock Mode. Fast Counter = 150, Low Spur Mode: a 1649.7 MHz to 1686.8 MHz Frequency Jump. Final Loop Bandwidth = 60 kHz B) Lock Time with the PLL in Normal Mode (Non Fast-lock), Low Spur Mode, a 1649.7 MHz to 1686.8 MHz Frequency Jump. Final Loop Bandwidth = 60 kHz
Rev. 0 | Page 8 of 20
ADF4154 CIRCUIT DESCRIPTION
REFERENCE INPUT SECTION
The reference input stage is shown in Figure 17. SW1 and SW2 are normally closed switches. SW3 is normally open. When power-down is initiated, SW3 is closed and SW1 and SW2 are opened. This ensures that the REFIN pin is not loaded on power-down.
POWER-DOWN CONTROL 100k TO R COUNTER BUFFER SW3 NO
04833-0-027
FPFD = REFIN x (1 + D ) R
where:
(2)
NC REFIN NC SW1
SW2
REFIN is the reference input frequency. D is the REFIN doubler bit. R is the preset divide ratio of binary 4-bit programmable reference counter (1 to 15). INT is the preset divide ratio of binary 9-bit counter (31 to 511). MOD is the preset modulus ratio of binary 12-bit programmable FRAC counter (2 to 4095). FRAC is the preset fractional ratio of binary 12-bit programmable FRAC counter (0 to MOD).
RF R COUNTER
The 4-bit RF R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 15 are allowed.
RF N-DIVIDER FROM RF INPUT STAGE N = INT + FRAC/MOD TO PFD N COUNTER
Figure 17. Reference Input Stage
RF INPUT STAGE
The RF input stage is shown in Figure 18. It is followed by a 2-stage limiting amplifier to generate the current mode logic (CML) clock levels needed for the prescaler.
BIAS GENERATOR 1.6V AVDD 2k 2k
THIRD ORDER FRACTIONAL INTERPOLATOR
INT REG
RFINA
MOD REG
FRAC VALUE
04833-0-016
Figure 19. A and B Counters
RFINB
PHASE FREQUENCY DETECTOR (PFD) AND CHARGE PUMP
The PFD takes inputs from the R counter and N counter and produces an output proportional to the phase and frequency difference between them. Figure 20 is a simplified schematic. The PFD includes a fixed delay element that sets the width of the antibacklash pulse, which is typically 3 ns. This pulse ensures that there is no dead zone in the PFD transfer function and gives a consistent reference spur level.
HI D1 U1 +IN CLR1 Q1 UP
04833-0-015
AGND
Figure 18. RF Input Stage
RF INT DIVIDER
The RF INT CMOS counter allows a division ratio in the PLL feedback counter. Division ratios from 31 to 511 are allowed.
INT, FRAC, MOD, AND R RELATIONSHIP
The INT, FRAC, and MOD values, in conjunction with the R counter, make it possible to generate output frequencies that are spaced by fractions of the phase frequency detector (PFD). See the RF Synthesizer: A Worked Example section for more information. The RF VCO frequency (RFOUT) equation is
DELAY
U3
CHARGE PUMP
CP
RFOUT = FPFD x (INT + (FRAC MOD))
where RFOUT is the output frequency of the external voltage controlled oscillator (VCO).
(1)
-IN
HI
CLR2 DOWN D2 Q2 U2
04833-0-017
Figure 20. PFD Simplified Schematic
Rev. 0 | Page 9 of 20
ADF4154
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4154 allows the user to access various internal points on the chip. The state of MUXOUT is controlled by M3, M2, and M1 (see Table 9). Figure 21 shows the MUXOUT section in block diagram form. The N-channel, open-drain, analog lock detect should be operated with an external pull-up resistor of 10 k nominal. When lock has been detected, the lock detect is high with narrow low-going pulses.
DVDD
Data is transferred from the shift register to one of four latches on the rising edge of LE. The destination latch is determined by the state of the two control bits (C2 and C1) in the shift register. These are the 2 LSBs, DB1, and DB0, as shown in Figure 2. The truth table for these bits is shown in Table 5. Table 6 shows a summary of how the latches are programmed.
PROGRAM MODES
Table 5 through Table 10 show how to set up the program modes in the ADF4154. The ADF4154 programmable modulus is double-buffered. This means that two events have to occur before the part uses a new modulus value. First, the new modulus value is latched into the device by writing to the R-divider register. Second, a new write must be performed on the N-divider register. Therefore, whenever the modulus value is updated, the N-divider register must then be written to so that the modulus value is loaded correctly.
04833-0-018
LOGIC LOW ANALOG LOCK DETECT R-DIVIDER OUTPUT N-DIVIDER OUTPUT FAST-LOCK CONTROL THREE-STATE OUTPUT DIGITAL LOCK DETECT LOGIC HIGH DGND MUX CONTROL MUXOUT
Table 5. C2 and C1 Truth Table
Control Bits C2 C1 0 0 0 1 1 0 1 1 Data Latch N-divider register R-divider register Control register Noise and spur register
Figure 21. MUXOUT Schematic
INPUT SHIFT REGISTERS
The ADF4154 digital section includes a 4-bit RF R counter, a 9-bit RF N counter, a 12-bit FRAC counter, and a 12-bit modulus counter. Data is clocked into the 24-bit shift register on each rising edge of CLK. The data is clocked in MSB first.
Rev. 0 | Page 10 of 20
ADF4154 REGISTERS
Table 6. Register Summary
N-DIVIDER REG
FAST-LOCK
9-BIT RF INTEGER VALUE
12-BIT RF FRACTIONAL VALUE
CONTROL BITS
DB23 FL1
DB22 N9
DB21 DB20 N8 N7
DB19 DB18 N6 N5
DB17 N4
DB16 DB15 DB14 N3 N2 N1
DB13 F12
DB12 DB11 F11 F10
DB10 F9
DB9 F8
DB8 F7
DB7 F6
DB6 F5
DB5 F4
DB4 F3
DB3 F2
DB2 F1
DB1 C2 (0)
DB0 C1 (0)
R-DIVIDER REG
PRESCALER
RESERVED
LOAD CONTROL
MUXOUT
4-BIT R COUNTER
12-BIT MODULUS
CONTROL BITS
DB23 P3
DB22 M3
DB21 DB20 M2 M1
DB19 DB18 P2 P1
DB17 R4
DB16 DB15 R3 R2
DB14 R1
DB13 M12
DB12 M11
DB11 DB10 M10 M9
DB9 M8
DB8 M7
DB7 M6
DB6 M5
DB5 M4
DB4 M3
DB3 M2
DB2 M1
DB1
DB0
C2 (0) C1 (1)
CONTROL REG
CP THREE-STATE
PD POLARITY
REFERENCE DOUBLER
RESERVED
DB15 0
DB14 0
DB13 0
DB12 DB11 DB10 0 U6 CP3
DB9 CP2
DB8 CP1
DB7 CP0
DB6 U5
DB5 U4
LDP
CP CURRENT SETTING
COUNTER RESET
DB2 U1
POWERDOWN
CP/2
CONTROL BITS
DB4 U3
DB3 U2
DB1
DB0
C2 (1) C1 (0)
NOISE AND SPUR REG
RESERVED
NOISE AND SPUR MODE
DB2 T1
NOISE AND SPUR MODE DB9 T8 DB8 T7 DB7 T6 DB6 T5 DB5 T4
RESERVED
CONTROL BITS
T9
T3
T2
C2 (1)
C1 (1)
Table 7. Noise and Spur Register
RESERVED
NOISE AND SPUR MODE
NOISE AND SPUR MODE
RESERVED
CONTROL BITS
DB10 T9
DB9 T8
DB8 T7
DB7 T6
DB6 T5
DB5 T4
DB4 T3
DB3 T2
DB2 T1
DB1 C2 (1)
DB0 C1 (1)
DB10, DB5, DB4, DB3 0
RESERVED RESERVED
THESE BITS MUST BE SET TO 0 FOR NORMAL OPERATION.
Rev. 0 | Page 11 of 20
04833-0-023
DB9, DB8, DB7, DB6, DB2 00000 11100 11111
NOISE AND SPUR SETTING LOWEST SPUR MODE LOW NOISE AND SPUR MODE LOWEST NOISE MODE
04833-0-019
DB10
DB4
DB3
DB1
DB0
ADF4154
Table 8. N-Divider Register Map
FAST-LOCK
9-BIT INTEGER VALUE (INT) 12-BIT FRACTIONAL VALUE (FRAC) CONTROL BITS
DB23 FL1
DB22 N9
DB21 DB20 DB19 DB18 N8 N7 N6 N5
DB17 N4
DB16 DB15 N3 N2
DB14 N1
DB13 F12
DB12 F11
DB11 F10
DB10 F9
DB9 F8
DB8 F7
DB7 F6
DB6 F5
DB5 F4
DB4 F3
DB3 F2
DB2 F1
DB1 C2 (0)
DB0 C1 (0)
F12 0 0 0 0 . . . 1 1 1 1
F11 0 0 0 0 . . . 1 1 1 1
F10 0 0 0 0 . . . 1 1 1 1 .......... .......... .......... .......... .......... .......... .......... .......... .......... .......... ..........
F3 0 0 0 0 . . . 1 1 1 1
F2 0 0 1 1 . . . 0 0 1 1
F1 0 1 0 1 . . . 0 1 0 1
FRACTIONAL VALUE (FRAC) 0 1 2 3 . . . 4092 4093 4094 4095
N9 0 0 0 0 . . . 1 1 1
N8 0 0 0 0 . . . 1 1 1
N7 0 0 0 0 . . . 1 1 1
N6 0 1 1 1 . . . 1 1 1
N5 1 0 0 0 . . . 1 1 1
N4 1 0 0 0 . . ... 1 1 1
N3 1 0 0 0 . . . 1 1 1
N2 1 0 0 1 . . . 0 1 1
N1 1 0 1 0 . . . 1 0 1
INTEGER VALUE (INT) 31 32 33 34 . . . 509 510 511
0 1
NORMAL OPERATION FAST-LOCK ENABLED
Rev. 0 | Page 12 of 20
04833-0-020
FL1
FAST-LOCK
ADF4154
Table 9. R-Divider Register Map
PRESCALER RESERVED LOAD CONTROL
MUXOUT 4-BIT R COUNTER 12-BIT INTERPOLATOR MODULUS VALUE (MOD) CONTROL BITS
DB23 DB22 DB21 DB20 P3 M3 M2 M1
DB19 DB18 P2 P1
DB17 DB16 DB15 DB14 DB13 R4 R3 R2 R1 M12
DB12 DB11 DB10 M11 M10 M9
DB9 M8
DB8 M7
DB7 M6
DB6 M5
DB5 M4
DB4 M3
DB3 M2
DB2 M1
DB1
DB0
C2 (0) C1 (1)
P3 LOAD CONTROL 0 1 NORMAL OPERATION LOAD FAST-LOCK TIMER
P1 0 1
PRESCALER 4/5 8/9 M12 0 0 0 . . . 1 1 1 1 M11 0 0 0 . . . 1 1 1 1 M10 0 0 0 . . . 1 1 1 1 .......... .......... .......... .......... .......... .......... .......... .......... .......... .......... M3 0 0 1 . . . 1 1 1 1 M2 1 1 0 . . . 0 0 1 1 M1 0 1 0 . . . 0 1 0 1
INTERPOLATOR MODULUS VALUE (MOD) 2 3 4 . . . 4092 4093 4094 4095
R4 0 0 0 0 . . . 1 1 1 1
R3 0 0 0 1 . . . 1 1 1 1
R2 0 1 1 0 . . . 0 0 1 1
R1 1 0 1 0 . . . 0 1 0 1
RF R-COUNTER DIVIDE RATIO 1 2 3 4 . . . 12 13 14 15
M3 0 0 0 0 1 1 1 1
M2 0 0 1 1 0 0 1 1
M1 0 1 0 1 0 1 0 1
MUXOUT THREE-STATE OUTPUT DIGITAL LOCK DETECT ANALOG LOCK DETECT N-DIVIDER OUTPUT LOGIC HIGH LOGIC LOW R-DIVIDER OUTPUT FAST-LOCK SWITCH
Rev. 0 | Page 13 of 20
04833-0-021
ADF4154
Table 10. Control Register Map
PD POLARITY CP THREE-STATE REFERENCE DOUBLE
RESERVED CP CURRENT SETTING
COUNTER RESET
DB2 U1
POWERDOWN
CP/2
LDP
CONTROL BITS
DB15 0
DB14 0
DB13 0
DB12 DB11 0 U6
DB10 CP3
DB9 CP2
DB8 CP1
DB7 CP0
DB6 U5
DB5 U4
DB4 U3
DB3 U2
DB1 C2 (1)
DB0 C1 (0)
U6 0 1
REFERENCE DOUBLER DISABLED ENABLED U1 0 1 COUNTER RESET DISABLED ENABLED
U2 0 1
CP THREE-STATE DISABLED THREE-STATE
U3 0 1 ICP(mA) /3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 CP0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 CP1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 CP0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 2.700k 1.090 2.180 3.260 4.350 5.440 6.530 7.620 8.700 0.540 1.100 1.640 2.180 2.730 3.270 3.810 4.350 5.100k 0.630 1.250 1.880 2.500 3.130 3.750 4.380 5.000 0.310 0.630 0.940 1.250 1.570 1.880 2.190 2.500 10.00k 0.290 0.590 0.880 1.150 1.470 1.760 2.060 2.350 0.150 0.300 0.440 0.588 0.740 0.880 1.030 1.180 U4 0 1 LDP 3 5
POWER-DOWN NORMAL OPERATION POWER-DOWN
U5 0 1
PD POLARITY NEGATIVE POSITIVE
Rev. 0 | Page 14 of 20
04833-0-022
ADF4154
REGISTER DEFINITION
N-Divider Register, R0
The on-chip N-divider register is programmed by setting R0[1, 0] to [0, 0]. Table 8 shows the input data format for programming this register.
Prescaler (P/P + 1)
The dual-modulus prescaler (P/P + 1), along with the INT, FRAC, and MOD counters, determines the overall division ratio from the RFIN to the PFD input. Operating at CML levels, it takes the clock from the RF input stage and divides it down for the counters. It is based on a synchronous 4/5 core. When set to 4/5, the maximum RF frequency allowed is 2 GHz. Therefore, when operating the ADF4154 above 2 GHz, this must be set to 8/9. The prescaler limits the INT value. With P = 4/5, NMIN = 31. With P = 8/9, NMIN = 91. The prescaler can also influence the phase noise performance. If INT < 91, a prescaler of 4/5 should be used. For applications where INT > 91, P = 8/9 should be used for optimum noise performance (see Table 9).
9-Bit INT Value
These nine bits control what is loaded as the INT value. This is used to determine the overall feedback division factor (see Equation 1).
12-Bit FRAC Value
These 12 bits control what is loaded as the FRAC value into the fractional interpolator. This value helps determine the overall feedback division factor (see Equation 1). The FRAC value must be less than the value loaded into the MOD register.
Fast-Lock
Setting the part to logic high enables fast-lock mode. To use fast-lock, the required time value for wide bandwidth mode needs to be loaded into the R-divider register. The charge pump current increases from 16x the minimum current and reverts back to 1x the minimum current once the time value loaded has expired. See the Fast-Lock Timer and Register Sequences section for more information.
4-Bit RF R Counter
The 4-bit RF R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the phase frequency detector (PFD). Division ratios from 1 to 15 are allowed.
12-Bit Interpolator Modulus/Fast-Lock Timer
Bits DB13-DB2 have two functions depending on the value of the load control bit: modulus or fast lock timer value. When the load control bit = 0 (DB23), the required modulus may be programmed into the R-divider register (DB13-DB2). When the load control bit = 1 (DB23), the required fast-lock timer value may be programmed into the R-divider register (DB13-DB2). This programmable register sets the fractional modulus, which is the ratio of the PFD frequency to the channel step resolution on the RF output. Refer to the RF Synthesizer: A Worked Example section for more information. The ADF4154 programmable modulus is double-buffered. This means that two events must occur before the part uses a new modulus value. First, the new modulus value is latched into the device by writing to the R-divider register. Second, a new write must be performed on the N-divider register. Therefore, whenever the modulus value is updated, the N-divider register must be written to so that the modulus value is loaded correctly.
R-DIVIDER REGISTER, R1
The on-chip R-divider register is programmed by setting R1[1, 0] to [0, 1]. Table 9 shows the input data format for programming this register.
Load Control
When set to logic high, the value being programmed in the modulus is not loaded into the modulus. Instead, it sets the fastlock timer. The value of the fast-lock timer/FPFD is the amount of time the PLL stays in wide bandwidth mode.
MUXOUT
The on-chip multiplexer is controlled by R1[22...20] on the ADF4154. Table 9 shows the truth table.
Digital Lock Detect
The digital lock detect output goes high if there are 40 successive PFD cycles with an input error of less than 15 ns. It stays high until a new channel is programmed or until the error at the PFD input exceeds 30 ns for one or more cycles. If the loop bandwidth is narrow compared to the PFD frequency, the error at the PFD inputs may drop below 15 ns for 40 cycles around a cycle slip. Therefore, the digital lock detect may go falsely high for a short period until the error again exceeds 30 ns. In this case, the digital lock detect is reliable only as a loss-of-lock detector.
CONTROL REGISTER, R2
The on-chip control register is programmed by setting R2[1, 0] to [0, 1]. Table 10 shows the input data format for programming this register.
RF Counter Reset
DB3 is the RF counter reset bit for the ADF4154. When this is 1, the RF synthesizer counters are held in reset. For normal operation, this bit should be 0.
Rev. 0 | Page 15 of 20
ADF4154
RF Charge Pump Three-State
This bit puts the charge pump into three-state mode when programmed to 1. It should be set to 0 for normal operation.
NOISE AND SPUR REGISTER, R3
The on-chip noise and spur register is programmed by setting R3[1, 0] to [1, 1]. Table 7 shows the input data format for programming this register.
RF Power-Down
DB4 on the ADF4154 provides the programmable power-down mode. Setting Bit DB4 to 1 powers down the device. Setting Bit DB4 to 0 returns the synthesizer to normal operation. While in software power-down mode, the part retains all information in its registers. Only when supplies are removed are the register contents lost. When a power-down is activated, the following events occur: 1. 2. 3. 4. 5. 6. All active dc current paths are removed. The synthesizer counters are forced to their load state conditions. The charge pump is forced into three-state mode. The digital lock detect circuitry is reset. The RFIN input is de-biased. The input register remains active and capable of loading and latching data.
Noise and Spur Mode
Noise and spur mode allows the user to optimize a design either for improved spurious performance or for improved phase noise performance. When the lowest spur setting is chosen, dither is enabled. This randomizes the fractional quantization noise so that it looks more like white noise rather than spurious noise. This means that the part is optimized for improved spurious performance. This operation would normally be used when the PLL closed-loop bandwidth is wide for fast-locking applications. A wide-loop bandwidth is seen as a loop bandwidth greater than 1/10 of the RFOUT channel step resolution (fRES). A wide-loop filter does not attenuate the spurs to a level that a narrow-loop bandwidth would. When the low noise and spur setting is enabled, dither is disabled. This optimizes the synthesizer to operate with improved noise performance. However, the spurious performance is degraded in this mode compared to the lowest spurs setting. To further improve noise performance, the lowest noise setting option can be used, which reduces the phase noise. As well as disabling the dither, it ensures that the charge pump operates in an optimum region for noise performance. This setting is extremely useful where a narrow-loop filter bandwidth is available. The synthesizer ensures extremely low noise and the filter attenuates the spurs. The typical performance characteristics give the user an idea of the trade-off in a typical WCDMA setup for the different noise and spur settings.
Lock Detect Precision (LDP)
When the LDP bit is programmed to 0, 24 consecutive reference cycles of 15 ns must occur before the digital lock detect is set. When this bit is programmed to 1, 40 consecutive reference cycles of 15 ns must occur before digital lock detect is set.
Phase Detector Polarity
DB6 in the ADF4154 sets the phase detector polarity. When the VCO characteristics are positive, this should be set to 1. When they are negative, it should be set to 0.
RESERVED BITS
These bits should be set to 0 for normal operation.
Charge Pump Current Setting
DB7, DB8, DB9, and DB10 set the charge pump current, which should be set according to the loop filter design (see Table 10).
RF SYNTHESIZER: A WORKED EXAMPLE
This equation governs how the synthesizer should be programmed.
RFOUT = [INT + (FRAC/MOD)] x [FPFD]
REFIN Doubler
Setting the REFIN bit to 0 feeds the REFIN signal directly to the 4-bit RF R counter, which disables the doubler. Setting the REFIN bit to 1 multiplies the REFIN frequency by a factor of 2 before feeding into the 4-bit R counter. When the doubler is disabled, the REFIN falling edge is the active edge at the PFD input to the fractional synthesizer. When the doubler is enabled, both the rising and falling edges of REFIN become active edges at the PFD input. When the doubler is enabled and the lowest spur mode is chosen, the in-band phase noise performance is sensitive to the REFIN duty cycle. The phase noise degradation can be as much as 5 dB for the REFIN duty cycles outside a 45% to 55% range. The phase noise is insensitive to the REFIN duty cycle in the lowest noise mode and in the lowest noise and spur mode. The phase noise is insensitive to the REFIN duty cycle when the doubler is disabled.
(3)
where:
RFOUT is the RF frequency output. INT is the integer division factor. FRAC is the fractionality. MOD is the modulus. FPFD = [REFIN x (1 = D)/R]
(4)
where:
REFIN is the reference frequency input. D is the RF REFIN doubler bit. R is the RF reference division factor.
Rev. 0 | Page 16 of 20
ADF4154
For example, in a GSM 1800 system, where a 1.8 GHz RF frequency output (RFOUT) is required, a 13 MHz reference frequency input (REFIN) is available and a 200 kHz channel resolution (fRES) is required on the RF output.
MOD = REFIN f RES MOD = 13 MHz 200 kHz = 65 From Equation 4, FPFD = [13 MHz x (1 + 0)/1] = 13 MHz 1.8 G = 13 MHz x (INT + FRAC 65) INT = 138; FRAC = 30 (5) (6) resolution. A 13 MHz reference signal could be fed directly to the PFD. The modulus would be programmed to 520 when in PDC mode (13 MHz/520 = 25 kHz). The modulus would be reprogrammed to 65 for GSM 1800 operation (13 MHz/65 = 200 kHz). It is important that the PFD frequency remains constant (13 MHz). By keeping the PFD constant, the user can design a one-loop filter that can be used in both setups without running into stability issues. The ratio of the RF frequency to the PFD frequency affects the loop design. Keeping this relationship constant instead of changing the modulus factor results in a stable filter.
MODULUS
The choice of modulus (MOD) depends on the reference signal (REFIN) available and the channel resolution (fRES) required at the RF output. For example, a GSM system with 13 MHz REFIN would set the modulus to 65, resulting in the RF output resolution (fRES) of 200 kHz (13 MHz/65) that is necessary for GSM.
SPURIOUS OPTIMIZATION AND FAST-LOCK
The ADF4154 can be optimized for low spurious signals by using the noise and spur register. However, in order to achieve fast-lock time, a wider loop bandwidth is needed. Note that a wider loop bandwidth can lead to notable spurious signals, which cannot be reduced significantly by the loop filter. Using the fast-lock feature can achieve the same fast-lock time as the noise and spur register, but with the advantage of lower spurious signals, since the final loop bandwidth is reduced by a quarter.
REFERENCE DOUBLER AND REFERENCE DIVIDER
The reference doubler on-chip allows the input reference signal to be doubled. This is useful for increasing the PFD comparison frequency. Making the PFD frequency higher improves the noise performance of the system. Doubling the PFD frequency usually results in an improvement in noise performance of 3 dB. It is important to note that the PFD cannot be operated above 32 MHz due to a limitation in the speed of the - circuit of the N divider.
FAST-LOCK TIMER AND REGISTER SEQUENCES
If the fast-lock mode is used, a timer value needs to be loaded into the PLL to determine the time of the wide bandwidth. When the load control bit = 1, the timer value is loaded via the 12-bit modulus value. To use fast-lock, the PLL must be written to in the following sequence: 1. Load the R-divider register with DB23 = 1 and the chosen fast-lock timer value (DB13-DB2) instead of the modulus. Note that the duration of time the PLL remains in wide bandwidth is equal to the fast-lock timer/FPFD. Load the noise and spur register. Load the control register. Load R-divider register with DB23 = 0 and MUXOUT = 110 (DB22-DB20). All the other needed parameters, including the modulus, also need to be loaded. Load the N-divider register, including fast-lock = 1 (DB23), to activate fast-lock mode.
12-BIT PROGRAMMABLE MODULUS
Unlike most other fractional-N PLLs, the ADF4154 allows the user to program the modulus over a 12-bit range. This means that the user can set up the part in many different configurations for the application, when combined with the reference doubler and the 4-bit R counter. For example, consider an application that requires a 1.75 GHz RF and a 200 kHz channel step resolution. The system has a 13 MHz reference signal. One possible setup is feeding the 13 MHz directly to the PFD and programming the modulus to divide by 65, which would result in the required 200 kHz resolution. Another possible setup is using the reference doubler to create 26 MHz from the 13 MHz input signal. The 26 MHz signal is then fed into the PFD, which programs the modulus to divide by 130. This setup also results in 200 kHz resolution and offers superior phase noise performance over the previous setup. The programmable modulus is also very useful for multistandard applications. If a dual-mode phone requires PDC and GSM 1800 standards, the programmable modulus is a huge benefit. The PDC requires a 25 kHz channel step resolution, whereas the GSM 1800 requires a 200 kHz channel step
2. 3. 4.
5.
Once this procedure is completed, future frequency jumps deploying fast-lock need to repeat only Step 5.
Rev. 0 | Page 17 of 20
ADF4154
If fast-lock is not used, then use the following sequence: 1. 2. 3. 4. Load the noise and spur register. Load the control register. Load the R-divider register with DB23 = 0 and other necessary parameters. Load the N-divider register, including fast-lock = 0 (DB23) for normal operation.
R1A MUXOUT
04833-0-030
ADF4154
CP C1 C2
R2 VCO C3
R1
Figure 23. Fast-lock Loop Filter Topology--Topology 2
To change frequency, only Step 4 need be repeated.
SPURIOUS SIGNALS
Predicting Where They Appear
As in integer-N PLLs, spurs appear at PFD frequency offsets from the carrier. In a fractional-N PLL, spurs also appear at frequencies equal to the RFOUT channel step resolution (fRES). The third-order fractional interpolator engine of the ADF4154 may also introduce subfractional spurs. If the fractional denominator (MOD) is divisible by 2, spurs appear at 1/2 fRES. If the fractional denominator (MOD) is divisible by 3, spurs appear at 1/3 fRES. Harmonics of all spurs mentioned also appear. With the lowest spur mode enabled, the fractional and subfractional spurs are attenuated dramatically. The worst-case spurs appear when the fraction is programmed to 1/MOD. For example, in a GSM 900 MHz system with a 26 MHz PFD frequency and an RFOUT channel step resolution (fRES) of 200 kHz, the MOD = 130. PFD spurs appear at 26 MHz offset and fractional spurs appear at 200 kHz offset. Since the MOD is divisible by 2, subfractional spurs are also present at 100 kHz offset.
FAST-LOCK: A WORKED EXAMPLE
Consider an example in which PLL has reference frequencies of 13 MHz and FPFD = 13 MHz and a required lock time of 50 s. Therefore, the PLL is set to wide bandwidth for 40 s. If the time period chosen for the wide bandwidth is 40 s, then Fast-lock timer value = time in wide bandwidth x FPFD Fast-lock timer value = 40 s x 13 MHz = 520 Therefore, 520 has to be loaded into the R-divider register in Step 1 of the sequence described in the Fast-Lock Timer and Register Sequences section.
FAST-LOCK: LOOP FILTER TOPOLOGY
To use fast-lock mode, an extra connection from the PLL to the loop filter is needed. The MUXOUT must reduce the damping resistor in the loop filter to 1/4 while in wide bandwidth mode. This is required because the charge pump current is increased by 16 while in wide bandwidth mode and stability must be ensured. This can be done with the following two topologies: 1. 2. Divide the damping resistor (R1) into two values (R1 and R1A) of ratio 1:3 (see Figure 22). Use an extra resistor (R1A) and connect it directly from the MUXOUT, as shown in Figure 22. The extra resistor must be chosen such that the parallel combination of an extra resistor and the damping resistor (R1) is reduced to 1/4 of the original value of R1 alone (see Figure 23).
ADF4154
CP C1 C2 R1 MUXOUT
04833-0-029
FILTER DESIGN--ADISIMPLL
A filter design and analysis program is available to help the user implement the PLL design. Visit www.analog.com/pll for a free download of the ADIsimPLL software. The software designs, simulates, and analyzes the entire PLL frequency and time domain response. Various passive and active filter architectures are allowed. Rev. 2 of ADIsimPLL allows analysis of the ADF4154.
INTERFACING
The ADF4154 has a simple, SPI(R) compatible serial interface for writing to the device. SCLK, SDATA, and LE control the data transfer. When LE (latch enable) is high, the 22 bits that have been clocked into the input register on each rising edge of SCLK are transferred to the appropriate latch. See Figure 2 for the timing diagram and Table 5 for the latch truth table. The maximum allowable serial clock rate is 20 MHz. This means that the maximum update rate possible for the device is 909 kHz or one update every 1.1 s. This is more than adequate for systems that have typical lock times in the hundreds of microseconds.
R2 VCO C3
R1A
Figure 22 Fast-lock Loop Filter Topology--Topology 1
Rev. 0 | Page 18 of 20
ADF4154
ADuC812 Interface
Figure 24 shows the interface between the ADF4154 and the ADuC812 MicroConverter(R). Since the ADuC812 is based on an 8051 core, this interface can be used with any 8051-based microcontroller. The MicroConverter is set up for SPI master mode with CPHA = 0. To initiate the operation, bring the I/O port driving LE low. Each latch of the ADF4154 needs a 24-bit word, which is accomplished by writing three 8-bit bytes from the MicroConverter to the device. After the third byte is written, the LE input should be brought high to complete the transfer. When operating in the mode described, the maximum SCLOCK rate of the ADuC812 is 4 MHz. This means that the maximum rate at which the output frequency can be changed is 180 kHz.
ADuC812
SCLOCK MOSI
ADSP-21xx
SCLOCK DT TFS
ADF4154
SCLK SDATA LE
I/O FLAGS
Figure 25. ADSP-21xx to ADF4154 Interface
PCB DESIGN GUIDELINES FOR CHIP SCALE PACKAGE
The lands on the chip scale package (CP-20) are rectangular. The printed circuit board pad for these should be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. The land should be centered on the pad. This ensures that the solder joint size is maximized. The bottom of the chip scale package has a central thermal pad. The thermal pad on the printed circuit board should be at least as large as this exposed pad. On the printed circuit board, there should be a clearance of at least 0.25 mm between the thermal pad and the inner edges of the pad pattern to avoid shorting. Thermal vias may be used on the printed circuit board thermal pad to improve thermal performance of the package. If vias are used, they should be incorporated into the thermal pad at 1.2 mm pitch grid. The via diameter should be between 0.3 mm and 0.33 mm, and the via barrel should be plated with 1 oz. of copper to plug the via. The user should connect the printed circuit board thermal pad to AGND.
ADF4154
SCLK SDATA LE
I/O PORTS MUXOUT (LOCK DETECT)
Figure 24. ADuC812 to ADF4154 Interface
ADSP-2181 Interface
Figure 25 shows the interface between the ADF4154 and the ADSP-21xx digital signal processor. As discussed previously, the ADF4154 needs a 24-bit serial word for each latch write. The easiest way to accomplish this using the ADSP-21xx family is to use the autobuffered transmit mode of operation with alternate framing. This provides a means for transmitting an entire block of serial data before an interrupt is generated. Set up the word length for eight bits and use three memory locations for each 24-bit word. To program each 24-bit latch, store each of the three 8-bit bytes, enable the autobuffered mode, and write to the transmit register of the DSP. This last operation initiates the autobuffer transfer.
04833-0-024
Rev. 0 | Page 19 of 20
04833-0-025
MUXOUT (LOCK DETECT)
ADF4154 OUTLINE DIMENSIONS
5.10 5.00 4.90
16 9
4.50 4.40 4.30
1 8
6.40 BSC
PIN 1 1.20 MAX 0.20 0.09 0.65 BSC 0.30 0.19 COPLANARITY 0.10 SEATING PLANE 8 0 0.75 0.60 0.45
0.15 0.05
COMPLIANT TO JEDEC STANDARDS MO-153AB
Figure 26. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters
4.0 BSC SQ 0.60 MAX PIN 1 INDICATOR TOP VIEW 3.75 BSC SQ 0.75 0.55 0.35 12 MAX 1.00 0.85 0.80 SEATING PLANE 0.50 BSC 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.20 REF COPLANARITY 0.08
11 10
0.60 MAX
16 15 20 1
BOTTOM VIEW
6 5
2.25 2.10 SQ 1.95
0.25 MIN 0.30 0.23 0.18
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
Figure 27. 20-Lead Lead Frame Chip Scale Package [LFCSP] 4 mm x 4 mm Body, (CP-20) Dimensions shown in millimeters
ORDERING GUIDE
Model ADF4154BRU ADF4154BRU-REEL ADF4154BRU-REEL7 ADF4154BCP ADF4154BCP-REEL ADF4154BCP-REEL7 EVAL-ADF4154EB1 Description Thin Shrink Small Outline Package (TSSOP) Thin Shrink Small Outline Package (TSSOP) Thin Shrink Small Outline Package (TSSOP) Lead Frame Chip Scale Package (LFCSP) Lead Frame Chip Scale Package (LFCSP) Lead Frame Chip Scale Package (LFCSP) Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Option RU-16 RU-16 RU-16 CP-20 CP-20 CP-20
Purchase of licensed I2C components of Analog Devices, Inc. or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specifications as defined by Philips.
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04833-0-4/04(0)
Rev. 0 | Page 20 of 20
This datasheet has been download from: www..com Datasheets for electronics components.


▲Up To Search▲   

 
Price & Availability of EVAL-ADF4154EB1

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X