|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
RSC-4128 Speech Recognition Processor Data Sheet General Description The RSC-4128 represents Sensory's next generation speech and analog I/O mixed signal processor. The RSC-4128 is designed to bring advanced speech I/O features to cost sensitive embedded and consumer products. Based on an 8-bit microcontroller, the RSC4128 integrates speech-optimized digital and analog processing blocks into a single chip solution capable of accurate speech recognition; high quality, low data-rate compressed speech; and advanced music. Products can use one or all features in a single application. The RSC-4128 supports Sensory SpeechTM 7 technology, which includes advanced speech algorithms that add features and improve performance. Capable of running both new HMM and enhanced neural network technologies, accuracy in all kinds of noise is dramatically improved. New Speaker Verification technology is perfect for voice password security applications that must work in noisy environments. New high quality compressed speech technology reduces data rates by 5 times. New 8 voice MIDI-compatible music includes drum tracks, effectively increasing instruments beyond 8. Simultaneous music and speech rounds out the Sensory SpeechTM 7 technology. The RSC-4128 also supports the revolutionary capability of creating speaker independent recognition sets by simply typing in the desired recognition vocabulary! A few keystrokes creates a recognition set in seconds without the wait or cost of recording sessions to train the recognizer, speeding time to sales. A new and unique Audio Wakeup feature listens while the RSC-4128 is in power down mode. When an audio event such as a clap or whistle occurs, Audio Wakeup will wakeup the RSC-4128 for speech or application tasks. Audio Wakeup is perfect for battery applications that require continuous listening and long battery life. In addition to improved recognition performance, the RSC-4128 provides further on-chip integration of features. A complete speech I/O application can be built with as few additional parts as a clock crystal, speaker, microphone, and few resistors and capacitors. Moreover, the RSC-4128 provides an unprecedented level of cost effective system-on-chip (SOC) integration, enabling many applications that require DSP and/or audio processing. The RSC-4128 may be used as a general-purpose mixed signal processor platform for custom algorithms, technologies and applications. Features Full Range of Sensory SpeechTM 7 Capabilities Enhanced Word Spotting capability (10 SI or 4 SD words) in parallel Noise robust Speaker Independent, Dependent & Continuous Listening recognition Speaker Verification (SVWS) - Noise robust voice biometric security High quality, 3.7-7.8 kbps speech synthesis & sound effects with Sensory "SX" synthesis technology 8 voice MIDI-compatible music synthesis coincident with speech; drum track feature enables additional voices Voice record & playback Audio Wakeup from sleep Integrated Single-Chip Solution 8-bit microcontroller ROMless, 128KByte and 256KByte ROM options 16 bit ADC, 10 bit DAC and microphone pre-amplifier Independent, programmable Digital Filter engine 4.8 KBytes total RAM (256Bytes "user" application RAM) Five timers (3 GP, 1 Watchdog, 1 Multi Tasking) Twin-DMA, Vector Math accelerator, and Multiplier Built-in Analog Comparator Unit (4 inputs) External memory bus: 20-bit Address(1Mbyte), 8-bit Data On chip storage for SD, SV, templates (10 templates) Code security through no ROM dump capability Uses low cost 3.58MHz crystal (internal PLL) Low EMI design for FCC and CE requirements 24 configurable I/O lines with 10 mA (typical) outputs Fully nested interrupt structure with up to 8 sources Optional Real Time Clock Long Battery Life 2.4 - 3.6V operation 12mA (typical) operating current at 3V 2 low power modes; 1 A typical sleep current Full Suite of Quick & Powerful Tools Quick Text-to-SI (T2SI) text entry to build noise robust SI recognition sets - low cost & push-button - no recording! Quick Synthesis for push-button speech compression Integrated Development Environment, C Compiler, Debugger & In Circuit Emulator from Phyton, Inc. (c) 2004 Sensory Inc. P/N 80-0206-H 1 RSC-4128 Data Sheet Table of Contents General Description ........................................................................................................................................................................ 1 RSC-4128 Overview ....................................................................................................................................................................... 4 Speech Technologies ..................................................................................................................................................................... 5 Speech Recognition...............................................................................................................................................................................................5 Speaker Verification...............................................................................................................................................................................................5 Speech and Music Synthesis.................................................................................................................................................................................5 Record and Playback.............................................................................................................................................................................................5 RSC-4128 Architecture ................................................................................................................................................................... 6 Reference Schematic...................................................................................................................................................................... 8 Using the RSC-4128 ....................................................................................................................................................................... 9 Instruction Set ........................................................................................................................................................................................................9 Stack ....................................................................................................................................................................................................................10 Register RAM.......................................................................................................................................................................................................10 L1 Vector Accelerator/Multiplier ...........................................................................................................................................................................11 Power and Wakeup Control .................................................................................................................................................................................11 General Purpose I/O ............................................................................................................................................................................................12 Memory Addressing .............................................................................................................................................................................................14 Wait States...........................................................................................................................................................................................................16 On-Chip ROM ......................................................................................................................................................................................................18 Oscillators ............................................................................................................................................................................................................18 Clocks ..................................................................................................................................................................................................................18 Timers/Counters ..................................................................................................................................................................................................19 Interrupts..............................................................................................................................................................................................................22 Analog input .........................................................................................................................................................................................................24 Audio Wakeup......................................................................................................................................................................................................25 Microphones ........................................................................................................................................................................................................26 Reset....................................................................................................................................................................................................................27 Digital-to-Analog-Converter (DAC) Output...........................................................................................................................................................27 Pulse Width Modulator (PWM) Analog Output.....................................................................................................................................................29 Comparator Unit...................................................................................................................................................................................................31 Instruction Set Opcodes and Timing Details ................................................................................................................................. 33 MOVE Group Instructions ....................................................................................................................................................................................33 ROTATE Group Instructions ................................................................................................................................................................................34 BRANCH Group Instructions ...............................................................................................................................................................................35 ARITHMETIC/LOGICAL Group Instructions ........................................................................................................................................................35 MISCELLANEOUS Group Instructions ................................................................................................................................................................36 Special Functions Registers (SFRs) Summary............................................................................................................................. 37 DC Characteristics ........................................................................................................................................................................ 39 A.C. Characteristics (External memory accesses) ........................................................................................................................ 39 Timing Diagrams........................................................................................................................................................................... 40 Absolute Maximum Ratings .......................................................................................................................................................... 40 Package Options .......................................................................................................................................................................... 41 2 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Die Pad Ring ................................................................................................................................................................................ 44 RSC-4128 Die Bonding Pad Locations......................................................................................................................................... 45 Mechanical Data ........................................................................................................................................................................... 46 Ordering Information..................................................................................................................................................................... 48 The Interactive SpeechTM Product Line ........................................................................................................................................ 49 3 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet RSC-4128 Overview The RSC-4128 is a member of the Interactive SpeechTM line of products from Sensory. It features a highperformance 8-bit microcontroller with on-chip ADC, DAC, preamplifier, RAM, ROM (except on ROM-less version), and optimized audio processing blocks. The RSC-4128 is designed to bring a high degree of integration and versatility into low-cost, power-sensitive applications. Various functional units have been integrated onto the CPU core in order to reduce total system cost and increase system reliability. The RSC-4128 operates in tandem with Sensory SpeechTM 7 firmware, an ultra compact suite of recognition and synthesis technologies. This reduced software footprint enables, for example, products with over 150 seconds of compressed speech, multiple speaker dependent and independent vocabularies, speaker verification, and all application code built into the RSC-4128 as a single chip solution. Revolutionary Text-to-Speaker-Independent (T2SI) technology allows the creation of SI recognition sets by simply entering text. The CPU core embedded in the RSC-4128 is an 8-bit, variable-length-instruction microcontroller. The instruction set is similar to the 8051 microcontroller, and has a variety of addressing mode, MOV and 16 bit instructions. The RSC-4128 processor avoids the limitations of dedicated A, B, and DPTR registers by having completely symmetrical sources and destinations for all instructions. The RSC-4128 provides a high level of on-chip features and special DSP engines, providing a very cost effective mixed signal platform for general-purpose applications and development of custom algorithms. The full suite of industry standard tools for easy product development makes the RSC-4128 an ideal platform for consumer electronics. RSC-4128 Block Diagram 3 .5 8 M H z O s c illa t o r o r R e s o n a to r 3 2 K H z O s c illa t o r ( o p t io n a l) ADC D ig ita l F ilte r s A u d io W akeup AGC T im e r s ( 3 ) W a tc h d o g T im e r DAC DAC Out M ic r o p h o n e P re -A m p and G a in C o n tr o l PW M RSC G e n e ra l P u rp o s e M ic r o c o n tr o lle r Speaker O ut In te r n a l R o m S p a c e (0 K , 1 2 8 K o r 2 5 6 K ) 4 .8 K S R A M L o w B a tte r y D e te c tio n R S C - 4 x S e r ie s C o m p a r a to r s ( 4 In p u t) V e c to r A c c e le r a to r w ith T w in D M A G e n e r a l P u r p o s e I/O 3 x 8 - b it p o r ts ( 2 4 I/O ) E x t e r n a l M e m o r y In t e r f a c e 8 - b it d a ta , 2 0 - b it A d d r e s s 4 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Speech Technologies Speech Recognition The RSC-4128 is designed to support HMM (Hidden Markov Modeling) as well as Neural Network technologies provided in Sensory SpeechTM 7 firmware, to perform speaker independent (SI) speech recognition. Speaker independent recognition requires on-chip or off-chip ROM to store the words to be recognized. Speaker dependent (SD) recognition requires programmable memory to store personalized speech templates. This programmable memory may be on-chip SRAM or off-chip Serial EEPROM, Flash Memory, or SRAM. The RSC-4128 has several additional speech recognition features as described below: Speaker Independent recognition requires no user training. The RSC-4128 can recognize up to 20 words in an active set (number of sets is limited only by internal ROM or external memory size). Text-to-SI (T2SI) recognition, based on HMM technology, allows creation of SI recognition sets in seconds by simply typing in the vocabulary desired, with no costs or delays associated with recording and training the recognizer. Speaker Dependent recognition allows the user to create names for products or customize vocabularies. Up to 100 words can be recognized in an active set (number of sets is limited only by internal ROM or external memory size). The RSC-4128 can store up to 10 SD words in on-chip SRAM. Continuous Listening allows the chip to continuously listen for a specific trigger word. With this feature, a product "activates" when a specific word is spoken, framed by quiet before and after. Continuous listening provides the lowest false fire rate for trigger words. Word Spotting allows the chip to continuously recognize for up to 10 SI or 5 SD words at a time. In word spotting mode, the word(s) to be recognized may be spoken in the middle of speech. Speaker Verification The RSC-4128 also supports Sensory's speaker verification (SV) technology - the most successful biometric security on the market. After a speaker trains the chip on a specific word or words, the chip is able to identify whether a particular word is spoken by the original speaker. The RSC-4128 can store up to 10 SV templates onchip, or more with external programmable memory. Speech and Music Synthesis The RSC-4128 provides high-quality speech synthesis using state-of-the-art frequency domain techniques in Sensory's new "SX" synthesis technology. Typical data rates for SX are approximately 6000 bits per second. One may select various data rates from approximately 3.7 to 7.8Kbps to manage speech quality versus allotted memory. Speech, music and sound effects may also be produced using the RSC-4128 8 bit, 58Kbps or 4 bit, 30Kbps compression technologies. The RSC-4128 provides high-quality, eight-voice, wave table music synthesis which allows multiple, simultaneous instruments for harmonizing. The RSC-4128 uses a MIDI-like system to generate music. One or more of the eight voices may be speech playback instead of music. One or more of the eight voices may be a drum track comprising multiple drums. In effect, this allows the number of simultaneous instruments to exceed 8. Speech and music synthesis requires on-chip or off-chip ROM to store data for synthesis playback. Easy to use tools allow the developer to record and compress their own voice talents and create with the push of a button, or to create their own MIDI scores and instruments. Record and Playback The RSC-4128 can perform speech record and playback (sometimes called "voice memo") at various compression levels depending on the quantity and quality of playback desired. Data rates less than 14,000 bits per second are achievable while maintaining very high quality reproduction. The record and playback technology also performs silence removal to improve sound quality and reduce memory requirements. 5 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet RSC-4128 Architecture The RSC-4128 is a highly integrated speech and analog I/O mixed signal processor that combines: 8-bit microcontroller with enhanced instructions and interrupt control, superior register architecture, independent Digital Filter engine and "L1" Vector Math Accelerator On-chip ROM and RAM (4.8 Kbytes), and the ability to address off-chip RAM, ROM, EPROM or Flash. Input microphone preamp and 16 bit Analog-to-Digital Converter (ADC) for speech and audio/analog input 10 bit Digital-to-Analog Converter (DAC), and 10 bit Pulse Width Modulator (PWM) to directly drive a speaker or other analog device Low power Audio Wakeup from power down mode, when a selected audio event, such as clap or whistle, occurs The RSC-4128 has 20-bit address and 8-bit data busses for interfacing with external memory. It includes an -XM input pin capable of enabling or disabling the internal ROM. NOTE: Neither the -XM input pin nor the extended memory busses are available on 64-lead LQFP packaged versions of the RSC-4128 with internal ROM. These are available on the die and 100 LQFP versions. Three bi-directional ports provide 24 configurable, general-purpose I/O pins to communicate with or control external devices with a variety of source and sink currents. Up to 4 of these I/O may be used as programmable Analog Comparator inputs. 16 may be used as I/O wakeup. The RSC-4128 has a high frequency (14.32 MHz) clock as well as a low frequency (32,768 Hz) clock. The processor clock can be selected from either source, with a selectable divider value. The device performs speech recognition when running at 14.32 MHz. The RSC4128 also supports programmable wait states to allow the use of slower memory. OSC1 is a very low-cost 3.58 MHz crystal oscillator which is used by a 4X PLL to generate the 14.32MHz clock. The OSC2 oscillator provides the options of using an external crystal or its own internal RC devices (no external components required for the internal RC mode). There are three programmable, general-purpose 8-bit counters / timers - Timers 1 and 3 are derived from OSC1, and Timer2 from OSC2. There is also a Watchdog timer that may be used to exit an undesired condition in program flow, and Multi-tasking timer to allow chip operations to share resources in parallel. 6 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Internal Block Diagram Data Sheet RSC-4128 A single chip speech I/O solution may be created with the RSC-4128. An external microphone passes an audio signal to the preamplifier and ADC to convert the incoming speech signal into digital data. Speech features are extracted using the Digital Filter engine. The microcontroller CPU processes these speech features using speech recognition algorithms in firmware, with the help of the "L1" Vector Accelerator and enhanced instruction set. The resulting speech recognition results may be used to control the consumer product application code, or to output speech or audio in the form of a dialog with the user of the consumer product. If desired, the output speech or audio signal from the RSC-4128 is generated by a DAC for external amplification into a speaker, or a PWM capable of directly driving a speaker at typical consumer product volumes. A typical product will require about $0.30 - $1.00 (in high volume) of additional components, in addition to the RSC-4128. The RSC-4128 also provides a very cost effective mixed signal platform for general-purpose applications and development of custom algorithms. A typical general purpose application will require about $0.30 - $0.50 (in high volume) of additional components, in addition to the RSC-4128. 7 P/N 80-0206-H (c) 2004 Sensory Inc. A1 A2 A3 A4 A5 A6 A0 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 Vdd Vdd A9 A10 A11 A12 A13 A14 A15 C7 A16 .1 Vdd .1 C3 NC A0 P0.1 NC A1 P0.2 A2 NC P0.3 A3 NC VDD PWM1 PWM0 GND NC A4 P0.4 NC A5 P0.5 NC A6 P0.6 NC .1 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 C9 .1 AVDD 2.2uF C10 Vdd C11 .1 DACOUT AVss VCM MICIN2 MICIN1 AMPCOM VREF AVdd NC P2.4 P2.3 NC P2.2 GND P2.1 P2.0 GND Vdd -RDF -WRD -RDR -WRC A19 A18 TESTP 8 Vdd C1 LS1 SPEAKER D[7:0] A[16:0] .1 U1 O0 O1 O2 O3 O4 O5 O6 O7 NC NC VCC 21 22 23 25 26 27 28 29 6 9 Vdd 8 C2 PDN 30 32 7 GND CE OE WE 24 .1 D0 D1 D2 D3 D4 D5 D6 D7 D7 D6 PDN D5 D4 A7 A8 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 20 19 18 17 16 15 14 13 3 2 31 1 12 4 5 11 10 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 RSC-4000 RSC-4128 Reference Schematic 3.58MHz Y1 D3 D2 U5 D1 D0 TSOP SST29VE010(TSOP) Vdd C5 12pF Schematic 1-1 P/N 80-0206-H C8 R2 100 C12 .1 R3 2.7K C14 X1 .1 100uF MICROPHONE .1 1uF C15 C16 C17 R1 100K C6 12pF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P0.0 D7 D6 PDN D5 D4 GND X01 XI1 Vdd -XM XO2 XI2 D3 D2 P2.7 D1 D0 GND Vdd P2.6 M1 P2.5 BRKPT -RESET P0.7 A7 A8 P1.0 A9 VDD GND A10 P1.1 A11 P1.2 A12 P1.3 A13 P1.4 A14 P1.5 A15 Vdd GND P1.6 A16 P1.7 A17 LLEN 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 U3 O0 O1 O2 O3 O4 O5 O6 O7 C4 .1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 Vdd AVDD PDN 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 22 24 1 31 BT1 3V C13 .1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 CE OE VPP PGM 27C010 13 14 15 17 18 19 20 21 D0 D1 D2 D3 D4 D5 D6 D7 Data Sheet (c) 2004 Sensory Inc. Data Sheet RSC-4128 Using the RSC-4128 Creating applications using the RSC-4128 requires the development of electronic circuitry, software code, and speech/music data files. Software code for the RSC-4128 can be developed using a complete suite of RSC-4128 development tools including In-Circuit Emulator, C Compiler, and "push button" tools for speech recognition and synthesis data files. Sensory provides free design reviews of customer applications to assist in the speech dialog and speech I/O design. Sensory also offers application development services. For more information about development tools and services, please contact Sensory. When using the RSC-4128 macro blocks such as the AFE, digital filters, L1, etc, for purposes other than as intended in the Sensory Speech 7 technology modules, in applications that will also use Sensory Speech 7, care must be taken to avoid conflicts that may cause adverse impact on functionality. Contact Sensory Technical Support for help in avoiding these conflicts. Instruction Set The instruction set for the RSC-4128 has 60 instructions comprising 13 move, 7 rotate, 11 branch, 22 arithmetic, and 7 miscellaneous instructions. All instructions are 3 bytes or fewer and no instruction requires more than 10 clock cycles (plus wait states) to execute. (see "Instruction Set Opcodes and Timing Details" for detailed descriptions) Flags The "flags" register (register FF) has bits that are set/cleared by arithmetic/logical instructions, a trap enable bit set under program control, a read-only stack overflow bit cleared at power on and set by stack wrap around, and the Global Interrupt Enable bit: 0FFH R/W Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: Bit 3: Bit 1: Bit 0: "flags" carry zero sign trap stkoflo stkfull (unused) gie (set = 1 when result of arith/log instruction is 0) (set = 1 when result of arith/log instruction has msb high) (read-only, initialized to 0, set to 1 on stack overflow) (read-only, initialized to 0, set to 1 on stack full) (Global Interrupt Enable) NOTE: The "trap" bit must be left written as "0". Flags Hold The "flagsHold" register (register CF) stores the "flags" value when an interrupt occurs. Unlike previous RSC chips, the RSC-4128 processor has read/write access to "flagsHold" for multi-tasking purposes. Since the "flags" register is restored from the "flagsHold" register upon return from interrupt, the "stkoflo" and "stkfull" bits are omitted from the "flagsHold" register to prevent inadvertent clearing of these bits. 0CFH R/W Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: Bit 2: Bit 1: Bit 0: "flagsHold" carry zero sign trap (unused - reads 0) (unused - reads 0) (unused - reads 0) gie NOTE: The "trap" bit must be left written as "0". See the discussion in "Interrupts" section relating to the value of "gie" stored in the "flagsHold" register when an interrupt occurs during execution of an instruction that clears the "gie" bit. 9 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Stack There is a 16-level, 16-bit stack for saving the program counter for subroutine calls and interrupt requests. The stack pointer wraps around on overflow or underflow. When the stack read and write pointers indicate that stack overflow has occurred, the "stkoflo" bit in the "flags" register is set. Once set, this bit can only be cleared by a processor reset. The bit may be tested by software, but it performs no other function. When the stack read and write pointers indicate that stack is full, the "stkfull" bit in the "flags" register is set. This bit will be reset once the stack is not full. Stack Pointers The 16-level stack has two 4-bit pointers, stack write and stack read. They are normally written by the processor upon execution of a "CALL" instruction or an interrupt. The stack also has a 6-bit index register "stkNdx" (register F6) and an 8-bit data port register "stkData" (register F7) that are used to access the stack contents as bytes in a register file under program control. The contents of the stack location selected by the "stkNdx" register may be read or written by the processor via MOV instructions at the "stkData" register. The stack register index must be written first, then the stack data can be read. The Stack read and write pointers (4 bits each) are also mapped to addresses accessible via the Stack Register Index. Stack contents accessed by value in stack register index ("stkNdx", register F6) 00H Stack0 Lo 08H Stack4 Lo 10H Stack8 Lo 18H 01H Stack0 Hi 09H Stack4 Hi 11H Stack8 Hi 19H 02H Stack1 Lo 0AH Stack5 Lo 12H Stack9 Lo 1AH 03H Stack1 Hi 0BH Stack5 Hi 13H Stack9 Hi 1BH 04H Stack2 Lo 0CH Stack6 Lo 14H StackA Lo 1CH 05H Stack2 Hi 0DH Stack6 Hi 15H StackA Hi 1DH 06H Stack3 Lo 0EH Stack7 Lo 16H StackB Lo 1EH 07H Stack3 Hi 0FH Stack7 Hi 17H StackB Hi 1FH 20(unused) 30(unused) 3EH StackWritePtr 3FH 2FH 3DH (4bits only) StackC Lo StackC Hi StackD Lo StackD Hi StackE Lo StackE Hi StackF Lo StacKF Hi StackReadPtr (4bits only) Register RAM The RSC-4128 has a total physical register RAM space of 896 bytes, divided into 14 banks of 64 bytes each. There is an additional 64 bytes of Special Function Registers (SFRs). Two of the register RAM banks are directly addressed as unbanked memory, and the other 12 banks are banked. Addressing 896 bytes requires an address width of 10 bits. (architecturally, an 11 bit address is implemented to allow for future increases in the register RAM). Logical register space addresses are 8 bits only (256 bytes), so 5 bank select bits in the "bank" register (register FC) are used so to access the full 896 bytes. The 256 byte logical register space map is divided into 4 different 64 byte sections: 000H-03FH 040H-07FH 080H-0BFH 0C0H-0FFH unbanked register RAM unbanked register RAM banked register RAM SFRs Bits [4:0] of the "bank" register determine which physical bank of 64 bytes is logically mapped to addresses 080H0BFH. When an address falls in the logically mapped range of 080H-0BFH, the lower 6 bits of the address (64 byte address) are used directly and the bank select bits are used as the upper 5 bits of the 11-bit physical register RAM address. When the address falls below the logically mapped range of 080H-0BFH, the lower 8 bits of the address are used directly to address the unbanked register RAM. When the address falls in the logically mapped range for the SFRs (0C0H-0FFH) the SFRs are addressed, not the register RAM. 10 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet Mapping of logical addresses 080H-0BFH ("bank" register FC is used) register FC [4:0] Physical RAM memory register FC [4:0] 00H 00-3FH 08H 01H 40-7FH 09H 02H 80-BFH 0AH 03H C0-FFH 0BH 04H 100-13FH 0CH 05H 140-17FH 0DH 06H 180-1BFH 0EH 07H 1C0-1FFH 0FH RSC-4128 Physical memory 200-23FH 240-27FH 280-2BFH 2C0-2FFH --- (unimplemented) --- (unimplemented) --- (unimplemented) --- (unimplemented) NOTE: If a value other than those indicated above is used for the "bank" register, an undefined state will result. See the "Special Functions Registers Summary" for details on the contents of SFRs. L1 Vector Accelerator/Multiplier A variety of macros are provided by Sensory that manipulate the L1 Vector Accelerator to provide signed and unsigned multiplication functions. See the "Sensory Speech 7 Technology Library Manual" for information on these macros and their application. The L1/Multiplier unit may be independently powered down by programming the register D6.Bit 4 to "0" ("clkExt" register, "L1clk_on" bit). Digital Filter The RSC-4128 has a Digital Filter engine capable of dividing up a frequency range into several smaller ranges. It is also capable of reporting characteristics of each range to the RSC-4128 processor. The configuration of the Digital Filter engine and access to signal characteristics generated are enabled by technology modules which are available from Sensory "Technology Support" upon request. Power and Wakeup Control The typical Active Supply Current is realized when operating with a main clock rate of 14.32 MHz at 3V and all I/O configured to the high-Z state. Lowering clock frequency reduces active power consumption, although Sensory Speech 7 technology typically requires a 14.32 MHz clock. Two supply current power-down modes are available - Sleep and Idle modes. In Sleep mode everything is stopped, and only an I/O event can initiate a wake-up. In Idle mode OSC2 and Timer2 continue to run, and an Audio Wakeup, I/O Wakeup or Timer2 interrupt request caused by overflow can generate a wake-up. Sleep mode is entered by setting register E8.Bit7=1 ("ckCtl" register; "pdn" bit), register E8.Bit0=1 ("osc1_off") and register E8.Bit1=0 (OSC2 off). Idle mode is entered by setting register E8.Bit7=1, register E8.Bit1=1 ("osc2_on") and register E8.Bit0=1. Setting register E8.Bit7=1 ("pdn") freezes the processor, but does not insure that the DAC, Audio Wakeup, and the PWM are placed in the lowest possible current-consumption state. Software control must power these blocks down prior to setting "pdn" to "1", according to the procedures indicated in "DAC", "Audio Wakeup", and "Pulse Width Modulator Analog Output" Sections. The "Sensory Speech 7 Technology Library Manual" provides sample code for achieving the lowest current-consumption state for Sleep and Idle modes. The state of "pdn" bit may be observed externally on the PDN pin (see pin definitions in "Package Options" section) and used to control power down of circuitry external to the RSC-4128, if desired. NOTE: GPIO (Ports 0,1 & 2) should be put in input mode and a known state (e.g. light pull-up) whenever possible to conserve power, and especially in powerdown mode to achieve the specified minimum supply current consumption. The external memory interface (A[19:0], D[7:0], -RDR, -WRC, -RDF and -WRD) automatically goes into a high-Z state and is pulled up by a 100 Kohm internal resistor when the "pdn" bit is set, to conserve current. Register E8 contains both the "pdn" bit and the processor clock selector (Bit2). The clock selector bit determines whether the 14.32 clock ("fast clock") or the 32KHz clock ("slow clock") will be used at wakeup time, independent of what clock rate was being used before or during power down mode. This allows the processor clock after wakeup 11 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet to be the same or different from the processor clock used when the power-down flag was set. (see "Clock" section for complete explanation) To minimize power consumption, most operational blocks on the chip also have individual power controls that may be selectively enabled or disabled by the programmer. Wakeup from powerdown Note that a Wakeup event does not cause a reset. The processor, which was "frozen" when register E8.Bit7 was set, will be restarted without loss of context. A reset of the chip will also cancel a power down mode, but with a corresponding loss of processor context. Wakeup events terminate a power-down state. In Sleep mode, only an I/O Wakeup event can initiate a wake-up. In Idle mode, an Audio Wakeup, I/O Wakeup or Timer2 interrupt request caused by overflow can generate a wakeup. An I/O Wakeup is enabled by setting the bit(s) high in registers E9 or EA corresponding to the desired I/O pin(s) to be used for wakeup. E9 controls P0 wakeup enable and EA controls P1 wakeup enable. The polarity of the wakeup event is controlled by putting the appropriate port pin in input mode and writing the appropriate bit in the output register for that pin to the desired polarity. (see "General Purpose I/O" section for complete explanation) When the value on the wakeup pin equals the value in the output register a wakeup will occur. A T2 Wakeup is enabled by setting register E8.Bit6 high. Then an overflow of timer T2 will generate an interrupt request, which in turn will trigger a wakeup event. Note that the Timer2 "irq" bit (register FE.Bit1) must be cleared prior to powering down to allow the wakeup interrupt request to occur. (the "Timers/Counters" section describes how timer T2 is configured) An Audio Wakeup is generated by special circuitry that can detect several classes of sounds, even while in powerdown mode. When the class of sound selected by the programmer is detected by this circuitry a wakeup event will occur. (see the "Audio Wakeup" section for more information) General Purpose I/O The RSC-4128 has 24 general-purpose I/O pins (P0.0-P0.7, P1.0-P1.7, P2.0-P2.7). Each pin can be programmed as an input with weak pull-up (~200k equivalent device); input with strong pull-up (~10k equivalent device); input without pull-up, or as an output with sufficient drive to light an LED. (See "DC Characteristics" section for I/O electrical characteristics.) This is accomplished by programming combinations of 48 bits of configuration registers assigned to the I/O pins. Two control registers, A and B, are used to control the nature of inputs and outputs for each port. Registers E6 ("p0CtlA") and E7 ("p0CtlB"), E2 ("p1CtlA") and E3 ("p1CtlB"), and DE ("p2CtlA") and DF ("p2CtlB"), are the control registers A and B for ports P0, P1 and P2, respectively. Each port pin's I/O configuration may be controlled independently by the state of it's corresponding bits in these registers. Control registers A and B together determine the function of the port pins as follows: B bit 0 0 1 1 A bit 0 1 0 1 Port Pin Function Input - Weak Pull-up Input - Strong Pull-up Input - No pull-up Output (For example, if register E7.Bit 4 is set high, and register E6.Bit 4 is low, then pin P0.4 is an input without a pull-up device.) After reset, pins P0.0-P0.7, P1.0-P1.7, and P2.5-P2.7 are set to be digital inputs with weak pull-ups, and pins P2.0P2.4 are configured as analog input pins with no pull-ups. Being reset as an input and lightly pulled to a known 12 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 (high) state ensures minimum power consumption as a default beginning. Sixteen of these pins (Ports P0 and P1) can also be configured as inputs to control IO Wakeup events. (see "Power and Wakeup Control" section). P2.0, P2.1, P2.3, and P2.4 can be configured as comparator inputs. P2.2 can be configured as a comparator reference. Some or all of P2.0-P2.4 can be configured as digital inputs by the use of the "cmpCtl" register (register D4) Bits[2:0] (see "Comparator Unit" section) Note: When configuring P2.0-P2.4 as digital inputs the associated weak pull-up should be selected as shown above. P0.0 and P0.2 can be configured as External Interrupts (see "Interrupts" section). P0.1 can be configured in input mode as a gate for an external event counter. (See "Timers/Counters" Section) Registers E5 ("p0In") and E4 ("p0Out"), E1("p1In") and E0 ("p1Out"), and DD ("p2In") and DC ("p2Out"), provide paths for data input and data output on P0, P1 and P2, respectively. The input registers are actually buffers which record the value at the ports at the time they are read. The output registers latch the data written to them and express it on the ports when the ports are configured as an output. 13 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Following is a summary of the general purpose I/O control registers: Register 0DCH Read/Write 0DDH Read 0DEH Read/Write 0DFH Read/Write 0E0H 0E1H 0E2H 0E3H 0E4H 0E5H 0E6H 0E7H Read/Write Read Read/Write Read/Write Read/Write Read Read/Write Read/Write P2[0:7] (port 2) output register. Cleared by reset. Port 2 input. Port 2 Control Register A. Cleared by reset. Port 2 Control Register B. Bits[7:5] cleared by reset. Bits[4:0] set by reset P1[0:7] (port 1) output register. Cleared by reset. Port 1 input. Port 1 Control Register A. Cleared by reset. Port 1 Control Register B. Cleared by reset. P0[0:7] (port 0) output register. Cleared by reset. Port 0 input. Port 0 Control Register A. Cleared by reset. Port 0 Control Register B. Cleared by reset. Data Sheet GPIO during powerdown GPIO should be put in input mode and a known state (e.g. light pull-up) whenever possible to conserve power, and especially in powerdown mode to achieve the specified minimum supply current consumption. Memory Addressing The RSC-4128 includes an external memory interface that allows connection with memory devices for storage of speaker-dependent speech recognition templates, audio record/playback data storage, extended durations of speech and music synthesis beyond the storage capabilities of on chip ROM, and code storage for the RSC4000 ROMless version. Thirty-four (34) pins are used to provide a bus interface between the processor and external ROM, EPROM, SRAM, or FLASH. (in die and 100LQFP versions; for RSC4128 64LQFP version, see Programmers Manual design notes) The RSC-4128 external memory interface has been improved for ATD-type memories. The external address lines remain stable during instruction cycles that access internal RAM or ROM. The -RDR and -RDF signals go high when not actively reading. The condition of the external data lines is weak pull-up when not accessing the external bus. (See "DC Characteristics" section for bus electrical characteristics.) The RSC4x can address up to 2MBytes of a combination of internal ROM and/or external ROM, RAM or flash memories without additional decoding circuitry. This is accomplished with 16 address outputs, A[15:0], and up to 4 extended address outputs A[19:16]. There are two different memory spaces of up to 1MBbyte each: Constant/Code Space and Data Space. ("Constant" Space is referred to as "Const" space in assembly and C-Data space in C) Data Space can be read or written. Constant/Code Space is typically read-only. Constant/Code Space When reading, Constant/Code Space can be either internal to the chip or external. Typical uses of this space are for code storage, and SI recognition set and/or compressed speech constant data storage. When the -XM input pin is held low, Constant/Code Space is external to the chip when reading and -RDR is the read strobe. When the -XM pin is high, Constant/Code Space reads are always internal to the chip, and are limited to the physical size of the internal ROM. When writing, -WRC is the write strobe regardless of the state of the -XM pin. Writing to Constant/Code Space requires the MOVC instruction, which is limited to the first 128KBytes of Constant/Code Space. When reading Constant/Code Space, an application can access up to 1MByte. However, only the first 128KBytes can be used by the processor for program instructions (Code). The MOVC instruction can only read these first 128KBytes. These first 128KBytes are partitioned into 64Kbyte banks, called Code Bank 0 and Code Bank 1. (NOTE: Code using both banks up to 128KBytes must provide "mirror" code in both banks for routines such as Interrupt Service, etc, with protocols to track bank identity.) The MOVX instruction can read the full 1Mbyte. However, the MOVC is more efficient for reading Constants within the current Code Bank. 14 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet The entire 1MByte of Constant/Code Space can be read with the following conditions. A[19:16] are generated from Bits[3:0] of Extended Addressing Register (register D2): 1) The MOVX instruction is used to read and Bit 4 ("rw") of Extended Addressing Register (register D2) is programmed to "0". RSC-4128 The upper addresses The first 128KBytes (addresses 00000H-1FFFFH; Code Banks 0 & 1) can be accessed in two additional ways. For these two cases, addresses A[19:17] are forced to zero by the RSC4x, and A[16] is generated from Bit 5 ("cb1") of the Extended Addressing Register. A "0" in "cb1" selects Code Bank 0 and a "1" selects Code Bank 1: 2) The processor fetches instructions from the active Code Bank. 3) The MOVC instruction is used to read from or write to the active Code Bank. Data Space Data Space is always external to the chip and can be up to 1MByte. Typical uses of this space are for storage of SD recognition template data and/or recorded audio data, and frequently the data is volatile. -RDF is the read strobe and -WRD is the write strobe. A special bit in the Extended Addressing Register must be set high to allow the processor to read from the data space using the MOVX instruction. When the "rw" bit (Bit 4 of Register D2) is set, the MOVX instruction reads from the Data Space. When writing to Data Space, the MOVX instruction generates a -WRD strobe, regardless of the state of the "rw" bit. Data space can be accessed in two ways. For both cases, upper addresses A[19:16] are generated from bits [3:0] of Extended Addressing Register: 1) The MOVX instruction is used to read and bit 4 ("RW") of Extended Addressing Register (register D2) is programmed to "1". 2) The MOVX instruction is used to write. Extended Address Register 0D2H R/W Bit [7:6] Bit 5 cb1 0: 1: ExtAdd (Unused) MOVC reads/writes and processor fetches access addresses 00000H-0FFFFH of Constant/Code Space (Code Bank 0) MOVC reads/writes and processor fetches access addresses 10000H-1FFFFH of Constant/Code Space (Code Bank 1) Cleared on reset. MOVX reads access Constant/Code Space MOVX reads access Data Space Cleared on reset. "eda" bits - extended address bits [19:16] used by MOVX to generate addresses bits A[19:16] of Data and/or Constant/Code Space. Cleared on reset. Bit 4 rw 0: 1: Bits [3:0] The programming of the Extended Addressing Register("extAdd") is independent of whether the ROM is external or internal. That is, an external ROM mirrors an internal ROM exactly. This allows products to be developed with external ROM and masked with the same binary in an internal ROM part. 15 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Note: Unlike the RSC-3x, the last 256 bytes of Data Space are not allocated for internal processor functions. All internal processor functions are mapped to the SFR area of Register space, leaving all Data space addresses potentially accessible as external memory. There are 8 data bus lines. These pins are bi-directional: they are normally inputs except when there is an external write to Code Space or Data Space. These pins, D[7:0], have weak pull-up devices (~100K ohm) to keep them from floating when no device is driving the data bus. External Memory Interface Control Signals There are 4 active low read/write strobes for reading from and writing to external Constant/Code Space or Data Space: -RDR, -WRC, -RDF, -WRD. To support cost effective software development for large memory spaces the external memory strobes are different from earlier RSC chips. The -RDR signal replaces the previous -RDC signal and the -RDF signal replaces the previous -RDD signal. The -XM pin replaces the previous -XML and -XMH pins on earlier RSC devices. The -WRC signal and the -WRD signal are the same as in previous RSC chips. (See "DC Characteristics" section for electrical characteristics.) The 20-bit extended address for a memory-reference instruction or a code fetch may be directed to the internal ROM, or it may be directed to an external ROM or flash. The address is always an external address if: 1) the instruction is MOVX read and the "rw" bit is set, or 2) the instruction is MOVX write, or 3) the -XM pin is low, or 4) the instruction is a MOVC write Otherwise the address is internal. The -XM pin is an active low input pin that disables internal ROM when pulled low, and forces the use of external memory for Constant/Code Space. Write accesses to Constant/Code Space (MOVC write; -WRC active) are always directed off-chip. The -XM pin has a weak pull-up device (~10K ohm) to enable the internal ROM when no connection is made to this pin. At the end of reset -XM is sampled and, if pulled low externally, the internal 10K ohm pull-up device is disabled. The -RDR signal goes low when the -XM pin is held low and either 1) the chip executes an instruction fetch, or 2) the chip executes a MOVC read instruction, or 3) the chip executes a MOVX read instruction and the "rw" bit is zero. This active low signal is used to enable an external ROM or other external memory containing both executable code and fixed, read-only data. The -RDF signal goes low when the chip executes a MOVX read instruction and the "rw" bit is set to 1. This active low signal is used to read an external flash or other external memory that is used solely for the purpose of Data Space, either read-only fixed data or read-write dynamic data. The -WRD signal goes low when the processor executes a MOVX write instruction. The -WRC signal goes low when the processor executes a MOVC write instruction. These signals do not depend on the contents of the Extended Address Register or the -XM signal, since a write by definition cannot be done to internal ROM. External Memory Interface during Powerdown The external memory interface (A[19:0], D[7:0], -RDR, -WRC, -RDF and -WRD) automatically goes into a high-Z state and is pulled up by a 100 Kohm internal resistor when the "pdn" bit is set, to conserve current. One output, PDN, is active high when RSC-4128 is powered-down. This pin can be connected to the (active low) chip enable pins of external memory devices to reduce power consumption during RSC-4128 power-down. Wait States General control of wait states is managed by register FC.Bits[7:5] ("bank" register). These bits are set to a value of 7 on reset, defaulting to slower memory. An initialization routine may be used to configure for faster memory. 16 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Access of external ROM space is always controlled by these wait state bits. Internal ROM space and all external R/W space accesses may also controlled by these bits, unless otherwise selected by bits in the clock extension register (register D6, "clkExt") The internal RAMs always operate with zero wait states. Register D6 provides for extended control of some clocks derived from OSC1 for producing additional timer scaling or specialized wait states. When Bit 5 is set, it overrides the "bank" register control of wait states during MOVX instructions which access external read/write memory (register D2.Bit4=1), and forces a fixed value of 4 wait states (nominal 350ns access). When Bit 7 is set, it overrides the "bank" register control of wait states during internal ROM accesses and forces zero wait states. Using these controls, various memory access speeds may be accommodated within one application. Bit 5 0: Certain MOVX* instructions use the Wait State divisor in register FC.Bits[7:5] 1:Certain MOVX* use fixed 4 Wait States (nominal 350nsec access) Cleared by reset 0: MT timer clock is disabled 1: MT timer clock I s enabled Cleared by reset 0: Accesses to internal ROM use the Wait State divisor set in register 0FCh[7:5] 1: Accesses to internal ROM use selected CLK (no wait states) Cleared by reset. Bytes 3 3 3 3 3 3 3 3 3 Cycles 5 5 6 4 7 8 7 8 10 +Cycles/ Waitstate 3 3 3 3 4 4 4* 4* 3 Bit 6 Bit 7 * MOVX accessing external read-write memory ("rw"; register D2.Bit4=1). Instruction Opcode Operand 1 Operand 2 Description MOV MOV MOV MOV MOVC MOVC MOVX MOVX POP 10 11 12 13 14 15 16 17 18 dest @dest dest dest dest @dest dest @dest dest Source Source @source #immed @source Source @source Source @++source register to register register to register-indirect register-indirect to register immediate data to register code space to register register to code space data space to register register to data space register to register data stack pop (source preincremented) register to register data stack push (dest postdecremented) RAMY to register, indirect register to RAMY, indirect register to register, direct, 16-bit MOV PUSH 19 @dest-- Source 3 9 3 MOVY MOVY MOVD 1A 1B 1C dest @dest dest_pair @source source source_pair 3 3 3 7 7 7 3 3 3 *MOVX instructions will have the number of wait states selected by register FC.Bits[7:5], unless register D2.Bit4 and register D6.Bit5 are set, in which case the number of wait states is fixed at 4. 17 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet On-Chip ROM The RSC-4128 includes integrated on-chip ROM. This ROM is enabled when the -XM pin is tied , or pulled high by it's own internal pullup resistor. This ROM space can combine both Code and Data. ROM code Security Feature The RSC-4128 has only one external memory enable pin (-XM), designed to prevent configuring code space for both internal and external memory. This discourages executing external code that reads internal code via the MOVC instruction and dumps it externally. In this way, a substantial measure of security is provided for the developer's application code. Oscillators Two independent oscillators in the RSC-4128 provide a high-frequency oscillator (OSC1), and a 32 KHz timekeeping and power-saving oscillator (OSC2). The oscillator characteristics are: OSC FREQ PLL PINS SOURCES Crystal 1 3.58 MHz 4X XI1 XO1 Ceramic resonator LC Crystal 2 32768 Hz N/A XI2 XO2 Internal RC OSC1 OSC1 is enabled by programming register E8.Bit0 to "0", which is the reset state for this bit. This bit is also programmed to "0" during a Wakeup Event, enabling OSC1, if register E8.Bit2 is programmed to "0". (see "Power and Wakeup Control" section) In this case, a 10-20 millisecond delay will be forced to allow OSC1 to reach stable oscillation. OSC1 must run at 3.58 MHz when using the Sensory Speech 7 technologies, but may be slower if the RSC-4128 is used as a general purpose platform for other applications. When OSC1 is disabled, the PLL which generates the 14.32MHz clock (CLK1) is also disabled. OSC2 OSC2 is enabled by programming register E8.Bit1 to "1". The reset state for this bit is "0", so this oscillator is disabled by reset. OSC2 will be enabled during a Wakeup Event if register E8.Bit2 is programmed to "1". (see "Power and Wakeup Control" section) No delay will be forced, as OSC2 is assumed to be running during Idle mode. The OSC2 source may be set to an external 32 KHz crystal by programming register EF.Bit2 to "0" (Note: register EF.Bit7 must be "0" to enable writing EF.Bit2) The external 32KHz crystal should be used when accurate timing and/or time-keeping is essential. In this mode, OSC2 is capable of achieving errors as low as 20ppm, depending on the quality of the crystal and crystal circuit design. A typical value for the crystal bias capacitors is 27pF, but this will vary depending on the crystal quality and stray capacitance inherent in the application board layout. The OSC2 source may be set to an on-chip RC by programming register EF.Bit2 to "1" (Note: register EF.Bit7 must be "0" to enable writing EF.Bit2). When using the on-chip RC, no external components are required for OSC1. The on-chip RC value will vary due to process, temperature and supply voltage variations, so this oscillator frequency will vary by +/- 30%. The on-chip RC mode should be used for low power modes where timing is not critical and minimum system cost is important. Oscillator Stabilization When exiting Sleep mode (see "Power and Wakeup Control" section) OSC1 will have a forced 10-20millisecond delay for stabilization if it is enabled. If OSC2 is enabled, it may require several seconds to stabilize, after which the RSC4128 will begin running. Therefore, for fast response out of Sleep mode OSC1 should be enabled. Clocks The RSC-4128 uses a fully static core - the processor can be stopped (by removing the clock source) and restarted without causing a reset or losing contents of internal registers. Dynamic operation is guaranteed from ~1KHz to 14.32 MHz. 18 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Fast Clock The 3.58 MHz OSC1 frequency is quadrupled by an on-chip PLL to produce a 14.32 MHz internal clock (CLK1). Creating the internal clock in this way avoids an expensive high frequency crystal, substantially reducing overall system cost. When used as the processor clock (see below), the 14.32 MHz internal clock creates internal RAM cycles of 70 nsec duration, and internal or external Code/Data memory cycles of 140 nsec duration. Careful design may allow operation with memories having access times as slow as 140 nsec. Slow Clock OSC2 generates an internal clock (CLK2) with an equivalent frequency to OSC2. When used as the processor clock (see below), the RAM access cycles are one CLK2 cycle and Code/Data access cycles are two CLK2 cycles. Processor Clock Either CLK1 or CLK2 can be selected as the processor clock (PCLK) on the fly by changing the value of register E8.Bit2. The reset state defaults to CLK1. (NOTE: it is possible to select a disabled clock as the processor clock. It is the responsibility of the programmer not to select a clock until the corresponding oscillator has been enabled and allowed to stabilize.) Power savings may result by using CLK2 when the processor is a lower activity mode and using CLK1 when in a higher activity mode. If the use of an external clock driver is desired, the output of that driver should be connected to the XI1 pin. After source selection, the processor clock can be divided-down in order to limit power consumption. E8.Bits 4 and 3 determine the divisor: E8.Bit4 0 0 1 1 E8.Bit3 0 1 0 1 Processor Clock Divisor 1/2 1/1 (reset default) 1/8 1/256 Register A Processor Clock divisor of 1/1 is typically required for Sensory Speech 7 technology. The processor clock is gated by the Wake-up delay and also gated by "pdn"=0 (register E8.Bit7), in such a way that the processor is stopped in a zero-power state with no loss of context. Other System Clocks The following functional clocks are generated from OSC1: CLK1, the digital filter clock, the analog front end (AFE) master clock, the L1 clock, Timer1 clock, Timer3 clock, and the Multi-Task timer clock. The Timer2 clock and the Watchdog timer clock are generated from OSC2. (see each block's section for clocking details) All clocks except the Timer2 and Audio Wakeup clocks are gated with the pdn = 0, to assure they are disabled during IDLE and SLEEP modes. Timer2 and Audio Wakeup can run during Idle mode to produce a T2 Wakeup or Audio Wakeup. (see "Power and Wakeup Control" section) Timers/Counters Four programmable timers and one fixed timer in the RSC-4128 provide a variety of timing/counting options. Timers 1, 2, 3 and the Multi-Tasking timer can all generate interrupts upon overflow. (See "Interrupts" section) Timers 1 and 3 Each of Timer1 (T1) and Timer3 (T3) consists of an 8-bit reload value register, an 8-bit up-counter, and a 4-bit decoded prescaler register. Each is clocked by CLK1 divided by 16. The reload register is readable and writeable by the processor. The counter is readable with precaution taken against a counter change in the middle of a read. NOTE: If the processor writes to the counter, the data is ignored. Instead, the act of writing to the counter causes the counter to preset to the reload register value. 19 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet When the timer overflows from FFH, a pulse is generated that sets register FE.Bit 0 ("irq" register; T1 bit) or register FE. Bit 4(T3 bit). The width of the pulse is the pre-scaled counter clock period. Instead of overflowing to 00, the counter is automatically reloaded on each overflow. For example, if the reload value is 0FAH, the counter will count as follows: 0FAH, 0FBH, 0FCH, 0FDH, 0FEH, 0FFH, 0FAH, 0FBH etc. The overflow pulse is generated during the period after the counter value reaches 0FFH. A separate 4-bit decoded prescaler register is between the clock source and the up-counter for each of T1 and T3. The 4bits represent the power of 2 used to divide the timer clock before applying it to the up-counter. For example, a prescaler value of 0 passes the timer clock directly through (divides by 2^0 = 1). A prescaler value of 5 divides the timer clock by 2^5 = 32. Prescaler value 0000 0001 0010 0011 0100 0101 0110 0111 Divisor 1 2 4 8 16 32 64 128 Prescaler value 1000 1001 1010 1011 1100 1101 1110 1111 Divisor 256 512 1024 2048 4096 8192 16384 32768 The resolution of T1 and T3 is 8 bits, but the range is 23 bits. The longest interval that can be timed by T1 or T3 is 2^15*256 clocks = 9.3 seconds. The 4-bit prescaler for T1 is in the Clock Extensions Register, (register D6.Bits[3:0]). The 4-bit prescaler for T3 is in the Timer3 Control Register (register D9.Bits[3:0]). In addition to its timing capability, T3 can also be configured as a counter of external events. In this configuration it uses either the rising or falling edge of a signal applied to I/O pin P0.1. The selected transition is internally synchronized to CLK1. The maximum external count rate for T3 is 447KHz. The Timer3 Control Register contains the counting/timing options for T3. The register is write-only. Bits[6:4] provide configuration control. Bit6 x 0 1 0 1 Bit 7 Bit5 0 0 0 1 1 Bit4 0 1 1 x x timer source T3CLK T3CLK T3CLK P0.1 P0.1 Configuration timer timer gated by P0.1 LOW timer gated by P0.1 HIGH count P0.1 events, rising edge count P0.1 events, falling edge 0: disable T3 and prescaler from counting/timing 1: enable T3 cleared by reset. 0: use rising edge for external event counting use LOW state on pin P0.1 for timer gating 1: use falling edge for external event counting use HIGH state on pin P0.1 for timer gating P/N 80-0206-H (c) 2004 Sensory Inc. Bit 6 20 Data Sheet cleared by reset Bit 5 0: use internal T3CLK for source (timing) 1: use external events on pin P0.1 for source (counting) cleared by reset 0: normal operation 1: T3 is gated by pin P0.1 according to Bit6 cleared by reset. Encoded prescaler for T3. (See prescaler table above). cleared by reset. RSC-4128 Bit 4 Bit 3:0 T1 and T3 can generate interrupts upon overflow by setting register FD.Bit0=1 and Bit4=1, respectively. (see "Interrupts" section) Timer2 Timer2 (T2) is clocked by CLK2 divided by 128. The overflow pulse from T2 can cause an interrupt request which in turn will cause a T2 Wake-up from power-down, if register E8.Bit6=1. (see "Power and Wakeup Control" section). Note that the Timer2 "irq" bit (register FE.Bit1) must be cleared prior to powering down to allow the wakeup interrupt request to occur. T2 can also generate a standard interrupt request by setting register FD.Bit1=1. (see "Interrupts" section) Timers 1, 2 and 3 Timer Reload and Counter Registers All are cleared to zero on reset. Register t1r t1v t2r t2v t3r t3v addr EBH ECH EDH EEH DAH DBH Read/Write Read Write Read/Write Read Write Read/Write Read Write Timer1 Counter Reload (2's complement of period) Timer1 current counter value Force load of Timer1 counter from reload register Timer2 Counter Reload (2's complement of period) Timer2 current counter value Force load of Timer2 counter from reload register Timer3 Counter Reload (2's complement of period) Timer3 current counter value Force load of Timer3 counter from reload register Multi-Task Timer The multi-tasking (MT) timer is intended to count a fixed interval of 858.1 microseconds. This provides a "heartbeat" for multi-tasking in the Sensory Speech 7 technology library. Other applications may find this useful for similar purposes. This interval is obtained by dividing the CLK1 rate, when running at 14.32 MHz, by a fixed factor of 12288. There is no configurability to the MT timer. One bit in the Clock Extension Register (D6.Bit6) enable this timer's clock. The MT timer overflow can generate an interrupt by setting register FD.Bit7=1. (see "Interrupts" section) Watchdog Timer Due to static electricity, voltage glitches, or other environmental conditions (or program bugs!), a software program can begin to operate incorrectly. The watchdog timer provides protection from such errant operation. The Watchdog Timer (WDT) unit comprises two control bits in the System Control Register (D5), a special instruction, two status bits, and a 17-bit counter. The counter, driven by OSC2, produces a toggle rate of approximately 4 seconds at the 17th bit. A 2-bit decoded mux in the "sysCtl" register (register D5) allows selecting the WDT timeout pulse from bit 9, 13, 15, or 17 of the counter. This selection sets the timeout in the range of 21 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet approximately 15.6 msec to 4 seconds. The accuracy of these times will depend on whether the OSC2 source is a 32 KHz crystal or the on-chip RC. The WDT is enabled by register FB.Bit4=1. This bit can only be set by execution of the "WDC" instruction. This bit is cleared by reset, so the WDT is disabled by reset. The bit is also cleared when E8.Bit7=1 (pdn), so the WDT is disabled in either SLEEP or IDLE mode. It is not automatically re-enabled on Wakeup. Program control cannot write to register FB.Bit4 to enable or disable the WDT. That is, FB.Bit4 is a read-only bit for normal register access instructions. Since the WDT needs OSC2 for its operation, once the WDC instruction has been executed and register FB.Bit4=1 to enable the WDT, OSC2 cannot be disabled by programming register E8.Bit1 =0 unless the "pdn" bit (register E8.Bit7) is also set simultaneously. This allows disabling the WDT only when entering a power down mode and is intended to reduce the probability of accidental software disabling of the WDT in active mode. Executing the WDC instruction clears the WDT counter, sets register FB.Bit4=1, clears register FB.Bit5=0 (wd_timed-out), and starts a new timeout period. The OSC2 oscillator may also be enabled by executing the WDC instruction. If the oscillator is stopped, executing this instruction also sets register E8.Bit1=1 to enable OSC2. In this case, timing will not begin until the oscillator is active. Once the WDT is started, software must execute the WDC instruction at a rate faster than the timeout period. Otherwise the watchdog circuit sets the "watch dog timed out" bit (register FB.Bit5) and generates a Timed Out Reset, which resets the RSC-4128. A Timed Out Reset disables the WDT. (See "Reset" section) Software in the reset routine can detect that the WDT timed out (FB.Bit5=1), since that is preserved during the Timed Out Reset. Placing the chip in Sleep or Idle mode disables the WDT operation. Timer Powerdown Some timers have independent power down control, while others may only be powered down by turning off their clock source, setting the "pdn" bit, or resetting. It is not required for the application to do this for full chip power down, as long as it complies with directions in the "Power and Wakeup Control" section. However, one may choose to reduce power consumption in active mode by turning off individual timers. Timer 3 and MT Timer may be independently powered down by setting the register D9.Bit 7 to "0" ("t3Ctl" register, "t3_on" bit) and register D6.Bit 6 to "0" ("clkExt" register, "MTclk_on" bit), respectively. Timer 1, Timer 2 and the WDT require special circumstances to powerdown, which are appropriate for their application. See their respective descriptions for more detail. Interrupts The RSC-4128 allows for 8 interrupt request sources, as selected by software. All are asynchronous positive edge activated except the two external requests, which have programmable edges. Each has its own mask bit and request bit in the "imr" and "irq" registers respectively. There is a Global Interrupt Enable flag in the "flags" registers. The "imr" and "irq" bits are listed below with the RSC-4128 interrupt source shown in parenthesis: 0FDH "imr" Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: Bit 2: Bit 1: Bit 0: 0FEH "irq" Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: 22 1=interrupt request #7 (Overflow of MT Timer) 1= interrupt request #6 (Edge of P0.2) 1=interrupt request #5 (Block End)(Reserved for Technology code) 1= interrupt request #4 (Overflow of Timer3) 1= interrupt request #3 (Edge of P0.0) P/N 80-0206-H (c) 2004 Sensory Inc. 1= enable interrupt request #7 (Overflow of MT timer) 1= enable interrupt request #6 (Edge of P0.2) 1= enable interrupt request #5 (Block End)(Reserved for Technology code) 1= enable interrupt request #4 (Overflow of Timer3) 1= enable interrupt request #3 (Edge of P0.0) 1= enable interrupt request #2 (Filter End Marker)(Reserved for Technology code) 1= enable interrupt request #1 (Overflow of Timer2) 1= enable interrupt request #0 (Overflow of Timer1) Data Sheet Bit 2: Bit 1: Bit 0: 1= interrupt request #2 (Filter End Marker)(Reserved for Technology code) 1= interrupt request #1 (Overflow of Timer2) 1= interrupt request #0 (Overflow of Timer1) RSC-4128 If an "irq" bit is set high and the corresponding "imr" bit is set high and the Global Interrupt Enable ("gie"; register FF.bit0) bit is set high, an interrupt will occur. Interrupts may be nested if software handles saving and restoring the "flagsHold" register (register CF). The "flags" register is copied to the "flagsHold" register and then the Global Interrupt Enable is cleared, preventing subsequent interrupts until the IRET instruction is executed. The IRET instruction will restore the "flags" register from the "flagsHold" register. The Global Interrupt Enable bit in the "flags" register must not be re-enabled during the period after an interrupt has been acknowledged and before an IRET instruction has been executed unless interrupt nesting is desired. If an interrupt occurs during an instruction that clears the Global Interrupt Enable bit (typically the CLI instruction) the value of the "gie" bit will be 0 upon completion of the Interrupt Service Routine and Return From Interrupt to the instruction following the one that cleared the "gie" bit. (NOTE: This is a change from the operation of the RSC-364.) The "flagsHold" register is accessible under program control at address CF in order to improve multi-tasking operation. External interrupts may be enabled on pins P0.0 (1st external interrupt request) and P0.2 (2nd external interrupt request), by setting register FD.Bit3=1 and register FD.Bit6=1, respectively. The polarity of the edges to trigger an external interrupt request for P0.0 and are controlled by register D5.Bits[1:0]. Setting D5.Bit0=0 will cause a positive going edge on P0.0 to generate and interrupt and D5.Bit0=1 will cause a negative going edge to generate an interrupt. The same controls for P0.2 are possible with D5.Bit1. The corresponding external "irq" flag will be set if the transition matches the interrupt edge control bit. NOTE: If P0.0 or P0.2 are configured as outputs, writing to those outputs can trigger external interrupt requests if the proper edge polarities occur. The user must be careful to avoid this, unless it is intended to use this as a way of generating interrupt requests under internal software control. An interrupt is disabled by writing a zero to the corresponding bit in the imr register (register 0FDH). However, an active interrupt request can still be pending. To be certain that an interrupt does not happen, you should clear the interrupt request flag in the irq register (register 0FEH) as well. For example: ; Disable timer 1 interrupt cli and mov sti imr,#0FEH irq,#0FEH ; mask new interrupt requests ; clear any pending interrupt request For each interrupt, execution begins at a different address: Interrupt #0 Interrupt #1 Interrupt #2 Interrupt #3 Interrupt #4 Interrupt #5 Interrupt#6 Interrupt#7 Address 04H Address 08H Address 0CH Address 10H Address 14H Address 18H Address 1CH Address 20H (Overflow of Timer 1) (Overflow of Timer 2) (Filter End Marker)(Reserved for Technology code) (Edge of P00) (Overflow of Timer 3) (Block End)(Reserved for Technology code) (Edge of P02) (Overflow of MT timer) The interrupt vector is generated as a 20-bit address. The low 16 bits are derived from the execution table above, and the high 4 bits are selected as a normal code fetch as described in the "Memory Addressing" section. Specifically, the "cb1" bit is not touched by the interrupt. 23 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet If the corresponding mask register bit is clear, the "irq" bit will not cause an interrupt. However, it can be polled by reading the "irq" register. "irq" bits can be cleared by writing a "0" to the corresponding bit at register FE (the "irq" register). "irq" bits cannot be set by writing to register FE. Writing a "1" to that register is a NO-OP. NOTE: Bit2 and Bit5 of the "irq" register should always be written as "1" when clearing other "irq" bits, to avoid conflicts with the Technology code use of these bits. In Idle mode, Timer2 continues to operate even when the rest of the RSC-4128 is powered-down. An overflow from Timer2 will set the corresponding "irq" flag even when there is no clock input to the processor. Note that the Timer2 "irq" bit (register FE.Bit1) must be cleared prior to powering down to allow the wakeup interrupt request to occur. This may also lead to normal interrupt processing once the processor is active, if the Timer 2 "imr" bit is set (register FD.Bit1). This interrupt response is unique from, and may be in addition to, the T2 Wakeup. Analog input The analog front end (AFE) for the RSC-4128 consists of a preamplifier with gain control, a 16-bit analog-to-digital converter, digital decimator and channel filters, and associated references. A single analog input can be processed through the AFE. All of this circuitry can be powered down to conserve battery life by programming register EF.Bit0 to "0". Setting this bit to "1" powers up the circuitry, requiring a settling time of approximately 10milliseconds. The analog front end (AFE) performs analog to digital conversions on a low-level signals, which may be derived from an electret microphone. The microphone signal is amplified by a preamp that provides four levels of gain, which are selected by programming register D5.Bits[4:3]. Full-scale output for the four settings corresponds to input signals of 100, 50, 25, and 12.5 millivolts Vpeak-peak, as shown in the table below. Gain "sysCtl" Bits[4:3] 00 01 10 11 Input Referred Noise Vrms 5.2* 4.9* 4.6* 4.4 Max Input Signal mVp-p 100 50 25 12.5 mVrms 35.4 17.7 8.8 4.4 Input signals higher than specified will produce a saturated full scale output with no wrap around. A line level audio input must be attenuated to the range shown above for use with the AFE. 24 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet Digital Transfer Functions RSC-4128 Lowpass response Detail of passband Frequency Below 8 kHz 9.395 kHz 20 kHz Above 20 kHz Attenuation Min Max 0 1.18 3 dB 87.82 53 NOTE: A 1uF capacitor should be connected to AMPCOM and tied to GND, a 2.2uF should be connected to VCM and tied to GND, and a 0.1uF capacitor should be connected to VREF and tied to GND. Failure to connect this capacitors will substantially degrade ADC performance, and Sensory Speech 7 technology. A/D Conversion The amplified signal is processed by a delta-sigma A/D converter that provides a 1-bit over-sampled digital signal. This digital stream is filtered and decimated to produce 16-bit samples at the fixed rate of 18,636 samples per second. The 16 bit signal will have about 12.5 bits of dynamic range, with about 10 bits above the noise level. These samples are then provided to the RSC-4128 digital filter unit formatted as signed two's-complement 16-bit values. The samples are stored in the digital filter input registers "adcSampleHi" (register F5) and "adcSampleLo" (register F4). Note: Using the AFE for general purposes other than as intended in Sensory Speech 7 technology modules may conflict with Sensory Speech 7. Such conflicts may adversely impact Sensory Speech 7 functionality and/or the functionality of the general purpose application. Care should be taken to avoid such conflicts. Contact Sensory Technical Support for help in this area. Audio Wakeup The Audio Wakeup unit is an analog/digital circuit that can be configured to wakeup from one of four specific audio events: 1) Two handclaps, or any two sharp, closely spaced sounds 2) Three handclaps, or any three sharp, closely spaced sounds 3) A whistle 4) Any "loud" sound above a specified amplitude, with duration options of 1 or 2 seconds 25 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Because it is intended to "listen" continuously at very low power levels, the Audio Wakeup unit must detect each of these events without any processor interaction. The processor configures and enables the unit under program control before going into Idle mode. Audio Wakeup is not available in Sleep mode because the unit requires the CLK2 signal. The detection signal from the Audio Wakeup unit can trigger a wakeup event, which starts the processor and allows further audio processing. The processor inputs to the Audio Wakeup are an enable signal and control signals to select for which sound to listen. For the lowest power consumption, the microphone should have a separate power source when in the Audio Wakeup mode. This is implemented outside the RSC-4128. See schematic 1-2 for details on this implementation. Schematic 1-2 AVdd MK1 1 2 R2 2.2K Q1 2N3906 3 1 R1 100 Example using one microphone for both Audio Wakeup and normal operation + RSC-4x MICROPHONE 2 C5 10uF example 2 R4 10K R5 R3 PDN MICIN2 AVdd VCM AVss Vdd Vdd AVdd + C7 10uF AVdd C6 .1 C1 .22 C2 2.2uF example 1 RSC-4x Example using one microphone for normal operation only + + .1 VREF C4 C3 1uF GND Vdd BT1 3V GND 100K 100 MK1 AMPCOM MICIN2 AVdd VCM AVss Vdd + C5 10uF AVdd VREF GND MICROPHONE MICIN1 2.2K 100 C1 .22 C2 2.2uF + + .1 C4 C3 1uF The RSC-4128 Sensory Speech 7 library contains routines for detecting each of the four audio events listed above. These routines also manage powerdown appropriately. See the "Sensory Speech 7 Technology Library Manual" for reference code to invoke these routines. Microphones A single electret microphone may be used both for the analog front-end input (for recognition purposes) and as the sound source for the Audio Wakeup unit. The current consumption and frequency response requirements are different for the two uses, so two microphone input pads are provided: MICIN1 for the normal recognition input to the analog front-end, and MICIN2 for the Audio Wakeup. A common microphone ground is used for both the analog front-end and the Audio Wakeup unit. In normal operation, the microphone would typically be powered from a source with an impedance in the range of 1-3 KOhms. In Audio Wakeup operation, the microphone source impedance must be in the range of 100 KOhms ("current starved") to reduce current consumption. The switching of the microphone input source is controlled by external circuitry under program control. See schematic 1-2 for details on this implementation. NOTE: See Design Notes - "Microphone Housing" and "Selecting Microphone" on the RSC-4x Demo/Evaluation CD. Improper microphone circuit and/or enclosure design will result in poor recognition performance. 26 P/N 80-0206-H (c) 2004 Sensory Inc. AVss Vdd 2 1 1 2 R2 R1 Px.n (Px.n is any available port I/O pin) MICIN1 AMPCOM Data Sheet RSC-4128 Reset An external reset is generated by applying a low condition for at least two clock cycles on -RESET, an active low Schmitt trigger input. The output of the Schmitt trigger passes through a 10 nsec glitch blocking circuit, followed by an asynchronous flip-flop. The output of the flip-flop generates active high reset throughout RSC-4128. The internal reset state is held for 20 msec (when clocked by a 14.32 MHz PCLK). The purpose is to allow the oscillator to stabilize and the PLL to lock before enabling the processor and the other RSC-4128 circuits. External reset clears the Global Interrupt Enable flag and begins execution at address 0h. The special function registers will be cleared, set, or left as-is, as detailed in the "Special Function Registers Summary" section. Watchdog Timeout Reset A special Watchdog Timeout Reset is produced if the Watchdog Timer is enabled and the Watchdog counter times out. The only difference between the Watchdog Timeout Reset and an ordinary reset is that the "wd_timed" bit in the "sysStat" register (register FB.Bit5) is preserved as "1" for a Watchdog Timeout Reset Digital-to-Analog-Converter (DAC) Output The DAC consists of an R-2R network with 10 bits of resolution and an output impedance of approximately 11 Kohms. An external amplifier is required to drive a speaker when using the DAC. The specifications of that amplifier will determine the best choice of speaker impedance and the resulting volume. The 10-bit resolution corresponds to an analog voltage range between 0V and Vdd minus 1 LSB (represented as "Vdd-"). At Vdd=3V, one LSB of the R-2R network corresponds to about 3 mV. For example: R2R Value 000H = 0v 001H = 0v+ 200H = Vdd/2 3FFH = VddDAC output; Vdd=3V 0.000V 0.003V 1.500V 2.997V There are two DAC output modes, full-scale and half-scale. In full-scale mode the output voltage swings between 0v and Vdd-; in half-scale mode the output swings between Vdd/4 and 3Vdd/4 minus 1 LSB (roughly Vdd/2 +/Vdd/4). Values written into the DAC hold register and certain Analog Control register bits are converted into analog voltages. The DAC hold register ("dac"; register FA) presents an 8-bit signed value to the DAC unit. In full-scale mode, the 8 most significant bits are driven by the DAC hold register and the 2 least significant bits are driven by the LSB1 and LSB0 bits in the Analog Control register ("anCtl"; register EF.Bits[5:4]). This results in a total output range of -512 to +511. In half-scale mode the 8 middle bits of are driven by the DAC hold register, the most significant bit is generated automatically by sign extension, and the least significant bit is driven by bit LSB1 in the Analog Control register. This gives a total output range of -256 to +255. The half-scale mode is enabled by setting the mode bit (d2a_half) equal to "1" in register EF.Bit3. The tables below show a selection of values and the resulting output voltage. Note: Register EF.Bit7 ("-anctlen") must be "0" in the value being written to register EF, when writing EF.Bit2. 27 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Full-Scale Mode (Output range 0v to Vdd- 1 LSB) Decimal DAC hold Analog Cntrl Digital input Equivalent reg[7:0] (hex) [5:4] (binary) -512 80H 00 000H -511 80H 01 001H -510 80H 10 002H -509 80H 11 003H -508 81H 00 004H -2 -1 0 +1 +2 +3 +4 +510 +511 FFH FFH 00H 00H 00H 00H 01H 7FH 7FH 10 11 00 01 10 11 00 10 11 1FEH 1FFH 200H 201H 202H 203H 204H 3FEH 3FFH Data Sheet Analog Voltage output General 0-3V (approx) 0V 0.000V 0V+ 1 LSB 0.003V 0.006V 0.009V 0.012V Vdd/2- 1 LSB Vdd/2 Vdd/2+ 1LSB 1.497V 1.500V 1.503V Vdd- 1LSB 2.994V 2.997V The translation in Full-Scale mode is: R2R[9] = dac[7] inverted R2R[8:2] = dac[6:0] R2R[1:0] = anCtl[5:4] Half-Scale Mode (Output range Vdd/4 to 3Vdd/4- 1 LSB) Decimal DAC hold Analog Cntrl Digital Input Equivalent reg[7:0] (hex) [5:4] (binary) -256 80H 0x 100H -255 80H 1x 101H -254 81H 0x 102H -253 81H 1x 103H -252 82H 0x 104H -2 -1 0 +1 +2 +3 +4 +254 +255 FFH FFH 00H 00H 01H 01H 02H 7FH 7FH 0x 1x 0x 1x 0x 1x 0x 0x 1x 1FEH 1FFH 200H 201H 202H 203H 204H 2FEH 2FFH Analog Voltage output General 0-3V (approx) Vdd/4 0.750V Vdd/4+ 1 LSB 0.753V 0.756V 0.759V 0.762V Vdd/2- 1LSB Vdd/2 Vdd/2+ 1LSB 1.497V 1.500V 1.503V 3Vdd/4-1 LSB 2.244V 2.247V The translation in Half-Scale mode is: R2R[9] = dac[7] inverted R2R[8:1] = dac[7:0] R2R[0] = anCtl[5] DAC Power Control The DAC has no explicit power control. It is turned off (placed into lowest current mode) by loading the value 80H into the DAC hold register, and 0 into the LSB1 and LSB0 bits of the Analog Control Register (register EF.Bits[5:4]). Note: register EF.Bit7 ("-anCtl" must be "0" in the value being written to register EF, when writing EF.Bits[5:0]. 28 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Pulse Width Modulator (PWM) Analog Output The PWM consists of circuitry to regulate the width of a pulse supplied to one of two outputs, PWM0 and PWM1, over a period of programmable duration. One or the other of the two outputs is held at ground and the other is driven with a pulse of programmable duration, giving "push-pull" drive. Both outputs have "low shoot-thru" transistors to reduce radiated EMI. Once programmed, the PWM produces outputs continuously until register values are changed. The PWM has both 8 and 10 bit modes. The PWM Control Register (`pwmCtl"; register D7) contains the PWM on/off control (Bit0), the sample period (Bits[3:2]), sample size selection controls (Bit5), and the two least-significant bits of the 10-bit output value (Bits[7:6]). The sample size defaults to 8 bits, with register D7.Bit5=0 ("tenBits"). A sample size of 10 bits is selected by setting "tenBits" =1. The PWM output impedance is approximately 11 Ohms. Of the standard speaker impedances available, an 8 ohm speaker will provide optimal volume when driven by the PWM. The PWM contains two counters. The data value counter is programmed with the value programmed in the "pwmData" register (register D8) in 8-bit mode. In 10-bit mode the data value counter uses "pwmData" and appends Bits[7:6] of "pwmCtl" as the least significant two bits to create a 10 bit value. Output data always lags input by one PWM sample period. The sample period counter is fixed and counts to 128. The prescaler in the PWM control register (register D7.Bits[3:2]) determines the clock for both the data value counter and the sample period counter. The prescaler divides the 14.3 MHz clock by 4,6, or 7, resulting in a PWM frequency of 27.9 KHz, 18.6Khz and 15.97 KHz, respectively. The PWM restarts every sample period, at which time either PWM0 or PWM1 pulses high. The selected signal pulses high for a duration determined by the data value and then returns low. The nonselected signal remains low. The pulsed output selection is controlled by the sign of the data. When Bit 7 of the "pwmData" register is 0, PWM0 pulses high while PWM1 remains 0. When Bit 7 of the "pwmData" register is 1, PWM1 pulses high while PWM0 remains low. When the data value in "pwmData" is 0, both signals remain low. When the sample period count selected by programming Bits[3:2] of the "pwmCtl" register D7.Bit has been reached, the PWM restarts. The PWM hardware sample period and the software data value updating must be synchronized to avoid aliasing. The following table shows the rates and pulse durations obtained for 8-bit mode ("tenBits" programmed to "0") SOFTWARE NOTE: "Full scale" output for all prescaler values is obtained by setting the data value to 7FH, so 8-bit signed data can be output at any of the three rates without amplitude adjustment. PWM timing for "tenBits"=0 Item prescaler=4 prescaler=6 nsec/clock (period clock) 280 420 CLK1 clocks per period 512 768 nsec/clock (sample 280 420 clock) PWM frequency 27.9 kHz 18.6 kHz pulse for data=01 4 H / 508 L 6 H / 762 L pulse for data=7F 508 H / 4L 762 H / 6 L prescaler=7 490 896 490 15.97 kHz 7 H / 889 L 889 H / 7 L For 10-bit mode ("tenBits" programmed to "1"), the sample period counter counts a full 7-bits (128 counts), exactly as when TenBits is 0. The 14.3 MHz clock is divided by the prescaler value and supplied to the sample period counter. The data value counter is clocked by the 14.3 clock divided by 2 for prescaler values 6 or 7, and is clocked directly by the 14.3 MHz clock when the prescaler value is 4. Table YY shows the rates and pulse durations obtained with TenBits set to 1. SOFTWARE NOTE: "Full scale" output is obtained with a different data value for each prescaler value. Only prescaler=4 supports a full 9-bit count (512), so true 10-bit signed data can be output only with prescaler=4. Otherwise the amplitudes must be adjusted to have maximum amplitude of 447 (prescaler=7) or 383 (prescaler=6). See "Additional considerations using the PWM for 10-bit Data" below. PWM timing for TenBits=1 Item prescaler=4 prescaler=6 nsec/clock (period ctr) 280 420 CLK1 clocks per period 512 768 29 prescaler=7 490 896 (c) 2004 Sensory Inc. P/N 80-0206-H RSC-4128 nsec/clock (data ctr) PWM frequency pulse for data=001 pulse for data=17F pulse for data=1BF pulse for data=1FF 70 27.9 kHz 1 H / 511 L 383 H / 129 L 447 H / 65 L 511 H / 1 L 140 18.6 kHz 2 H / 766 L 766 H / 2 L -- n/a --- n/a -140 15.97 kHz 2 H / 894 L 766 H / 130 L 894 H / 2 L -- n/a -- Data Sheet 30 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Additional considerations using the PWM for 10-bit Data The 14.3 MHz CLK1 clock rate of the RSC-4128 is not fast enough to provide PWM synchronization with 10-bit 8kHz or 9.3 kHz data. To understand this, consider a PWM rate of 8 kHZ (125 microsec). To output 10 bits (9 bits plus sign) during this interval, a source must provide 512 clocks, giving a source rate of 125000/512 = 244 nsec. The CLK1 period is 70 nsec, so the relationship between the source clock and CLK1 is 244/70 = 3.5, which is not an integer. So the source clock cannot be derived simply from CLK1. The RSC-4128 application developer should address this issue by using a "near-10-bit" resolution, as follows. The TenBits bit is set in the "pwmCtl" register, and the prescaler is programmed to 7 to produce a PWM frequency of 15.98 kHz (62.57 microseconds). During this interval there will be 62570/70 = 894 CLK1 clocks, or 894/2 (=447) data counter clocks. The number 447 thus represents the largest possible count that can be loaded into the data value counter. The range of allowable values is from -447 to +447. Any larger value would produce the same output of the PWM pulse "on" for the entire duration of the PWM period. Thus 447 represents "full scale" of the PWM. If all 10-bit data values are then scaled to a maximum of +/-447, the PWM will provide full-scale swing and (close-enough) synchronization at 8 kHz. The actual number of bits in the data is log2(447 - (-447)) = 9.8 bits. The developer must ensure that the value programmed in the data value counter must not exceed the range of -447 to +447. Sensory Speech 7 provides PWM output utilities for speech and music that manage the PWM for the developer, if so desired. (See "Sensory Speech 7 Technology Library Manual") PWM powerdown The PWM may be independently powered down by programming the register D7.Bit 0 to "0" ("pwmCtl" register, "pwm_on" bit). When the PWM is off, the PWM outputs PWM0 and PWM1 are in a high-Z state and pulled up by internal 10K resistors. The PWM must be explicitly turned off before setting "pdn" equal to 1 to achieve the lowest powerdown current. Comparator Unit The Comparator Unit consists of 2 analog comparators designated "A" and "B", a programmable voltage reference, selection circuitry, and two registers - the Comparator Control register ("cmpCtl") and the Comparator Reference ("cmpRef"). Register "cmpCtl" configures the comparator unit and provides the digital comparator outputs. Bits [2:0] are used to select from one of eight comparator configurations, in which some or all of P2.0-P2.4 may be analog or digital inputs. (See "RSC-4128 Comparator Unit" figure; "A" denotes analog input and "D" denotes digital input) Bits [3:0] are read-write. Register "cmpRef" controls the Comparator Reference Voltage. The unit can provide level information under software control about 4 external analog signals. All external signals connected to the comparator inputs must be between Vss and Vdd. Each comparator has two analog inputs, designated "+" and "-", and one digital output. When the analog voltage on the "+" input is greater than the analog voltage on the "-" input, the digital output is a high level. This is indicated by a "1" in the "cmpCtl" register (register D4) Bits 7 & 6 for Comparators A and B, respectively. When the analog voltage on the "+" input is less than the analog voltage on the "-" input, the digital output is a low level. This is indicated by a "0" in the "cmpCtl" register (register D4) Bits 7 & 6 for Comparators A and B, respectively. Bits 7 and 6 are the comparator outputs and are "Read-Only" by the processor. CmpCtl=000 A P2.0 A P2.3 A P2.1 A P2.4 B OFF A OFF D P2.0 D P2.3 D P2.1 D P2.4 B OFF CmpCtl=111 A OFF A P2.2 CmpCtl=001 A P2.0 A P2.3 A P2.1 A P2.4 iVREF D P2.2 CmpCtl=011 A P2.0 A P2.3 D P2.1 D P2.4 iVREF D P2.2 CmpCtl=101 D P2.0 D P2.3 A P2.1 A P2.4 iVREF D P2.2 B A OFF B OFF A B A D P2.2 CmpCtl=010 A P2.0 A P2.3 A P2.1 A P2.4 B A A P2.2 CmpCtl=100 A P2.0 A P2.3 D P2.1 D P2.4 B OFF A A P2.2 CmpCtl=110 D P2.0 D P2.3 A P2.1 A P2.4 B A OFF A P2.2 31 P/N 80-0206-H RSC-4128 Comparator Unit (c) 2004 Sensory Inc. RSC-4128 Data Sheet Each comparator can be separately enabled or disabled. When a comparator is disabled, both inputs are isolated from any circuitry common to both comparators, the inputs are grounded, and the comparator power is turned off. 32 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet Comparator Multiplexing RSC-4128 Each comparator "+" input has an analog multiplexer that selects between one of two external signals. When Bit3 of "cmpCtl" is programmed to "0", comparator input A+ is multiplexed to P2.0 and input B+ is multiplexed to P2.1. When Bit3 of "cmpCtl" is programmed to "1", comparator input A+ is multiplexed to P2.3 and input B+ is multiplexed to P2.4. The "-" inputs of both comparators are connected together. This common "-" input can be multiplexed to either an external comparator reference signal input through P2.2, or the Comparator Reference Voltage (CRV). Comparator Reference Voltage The internal Comparator Reference Voltage (CRV) is derived from a multi-tap resistive divider and a 4-bit analog multiplexer. Register "cmpRef" controls the Comparator Reference Voltage. The power for the Comparator Reference Voltage is provided by unregulated Vdd. This means that the CRV will track external voltages referenced from the system supply, giving consistent comparisons as the system supply drops. Power to the CRV is gated by decoding the comparator configuration. The voltage select value in "cmpRef" Bits[3:0] selects one of 16 outputs of an analog multiplexer connected to 16 equally spaced taps. The Comparator Reference Voltage covers the range from 0.15*Vdd to 0.90*Vdd in steps of 0.05*Vdd and is given by 0.15*Vdd + (D3[3:0]/20)*Vdd. In some configurations the Comparator Control register can be set up once and simply read thereafter. In many configurations it will be necessary to switch the input multiplexers and/or re-program the reference voltage repeatedly. These multiplexing and selection operations will have settling times of approximately 10 microseconds. When the "pdn" bit is set for Idle or Sleep mode the entire comparator unit is powered down, but the contents of the "cmpCtl" and "cmpRef" registers are preserved. When the RSC-4128 wakes up the comparators resume normal operation. Instruction Set Opcodes and Timing Details The RSC-4128 instruction set has 60 instructions comprising 13 move, 7 rotate/shift, 11 jump/branch, 13 register arithmetic, 9 immediate arithmetic, and 7 miscellaneous instructions. All instructions are 3 bytes or fewer, and no instruction requires more than 10 clock cycles (plus wait states) to execute. The column "Cycles" indicates the number of clock cycles required for each instruction when operating with zero wait states. Wait states may be added to lengthen all accesses to external addresses or to the internal ROM (but not internal SRAM). The column "+Cycles/Waitstate" shows the number of additional cycles added for each additional wait state. Opcodes are in HEX. MOVE Group Instructions Register-indirect instructions accessing code (MOVC), data (MOVX), technology (MOVY) or register (MOV) space locations use an 8-bit operand ("@source" or "@dest") to designate an SRAM register pointer to the 16-bit target address. The "source" or "dest" indirect pointer register must be at an even address unless it is a 8-bit pointer (indirect MOV). The LOW byte of the target address is contained at the pointer address, and the HIGH byte of the target address is contained at the pointer address+1. Unless the flags register is the destination, the carry, sign, and zero flags are not affected by MOV instructions. Instruction MOV MOV MOV MOV MOVC MOVC MOVX MOVX POP Opcode 10 11 12 13 14 15 16 17 18 Operand 1 dest @dest dest dest dest @dest dest @dest dest Operand 2 Source Source @source #immed @source Source @source Source @++source Description register to register register to register-indirect register-indirect to register immediate data to register code space to register register to code space data space to register register to data space register to register data stack pop (source preincremented) P/N 80-0206-H Bytes 3 3 3 3 3 3 3 3 3 Cycles 5 5 6 4 7 8 7 8 10 +Cycles/Waitstate 3 3 3 3 4 4 4* 4* 3 33 (c) 2004 Sensory Inc. RSC-4128 PUSH MOVY MOVY MOVD 19 1A 1B 1C @dest-dest @dest dest_pair Source register to register data stack push (dest postdecremented) @source RAMY to register, indirect source Register to RAMY, indirect source_pair register to register, direct, 16-bit MOV 3 3 3 3 9 7 7 7 3 3 3 3 Data Sheet * If register D6.Bit 5=1 (movX_4ws) and external read/write memory is selected by setting the "rw" bit (register D2.Bit4), MOVX instructions have four additional wait states. ROTATE Group Instructions Rotate group instructions apply only directly to register space SRAM locations. The carry flag is affected by these instructions, but the sign and zero flags are unaffected. Instruction RL RR RLC RRC SHL SHR SAR Opcode 30 31 32 33 34 35 36 Operand 1 dest dest dest dest dest dest dest Operand 2 Description rotate left, c set from b7 rotate right, c set from b0 rotate left through carry rotate right through carry shift left, c set from b7, b0=0 shift right, c set from b0, b7=0 shift right arithmetic, c set from b0, b7 duplicated Bytes 2 2 2 2 2 2 2 Cycles 5 5 5 5 5 5 5 +Cycles/Waitstate 2 2 2 2 2 2 2 34 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 BRANCH Group Instructions The branch instructions use direct address values rather than offsets to define the target address of the branch. This implies that binary code containing branches is not relocatable. However, object code produced by the RSC4128 assembler contains address references that are resolved at link time, so .OBJ modules are relocatable. The indirect jump instruction uses an 8-bit operand ("@dest") to designate an SRAM register pointer to the 16-bit target address. The "dest" pointer register must be at an even address. The LOW byte of the target address is contained at the pointer address, and the HIGH byte of the target address is contained at the pointer address+1. Instruction JC JNC JZ JNZ JS JNS JMP CALL RET IRET JMPR Opcode 20 21 22 23 24 25 26 27 28 29 2A Operand 1 dest low dest low dest low dest low dest low dest low dest low dest low @dest Operand 2 dest high dest high dest high dest high dest high dest high dest high dest high Description jump on carry = 1 jump on carry = 0 jump on zflag = 1 jump on zflag = 0 jump on sflag = 1 jump on sflag = 0 jump unconditional direct subroutine call return from call return from interrupt jump indirect Bytes 3 3 3 3 3 3 3 3 1 1 2 Cycles 3 3 3 3 3 3 3 3 2 2 4 +Cycles/Waitstate 3 3 3 3 3 3 3 3 1 1 2 ARITHMETIC/LOGICAL Group Instructions Arithmetic and logical group instructions apply only to Register Space SRAM locations. The results of the instruction are always written directly to the SRAM "dest" register. The exceptions are TM and CP instructions, which do not write the result to the "dest" register and only update the flags register based on the operation's outcome. All but the INCrement and DECrement instructions have both register source and immediate source forms. In each of the following instructions the sign and zero flags are updated based on the result of the operation. The carry flag is updated by the arithmetic operations (ADD, ADC, SUB, SUBC, CP, INC, DEC) but it is not affected by the logical operations (AND, TM, OR, XOR). Note: the carry is set high by SUB, CP, SUBC and DEC when a borrow is generated. 35 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Instruction Opcode Operand 1 Operand 2 Description AND 40 dest source logical and TM 41 dest source like AND, destination register unchanged OR 42 dest source logical or XOR 43 dest source exclusive or SUB 44 dest source subtract CP 45 dest source like SUB, destination register unchanged SUBC 46 dest source subtract w/carry ADD 47 dest source add ADC 48 dest source add w/carry INC 49 dest increment DEC 4A dest decrement AND 50 dest #immed logical and TM 51 dest #immed like AND, destination register unchanged OR 52 dest #immed logical or XOR 53 dest #immed exclusive or SUB 54 dest #immed subtract CP 55 dest #immed like SUB, destination register unchanged SUBC 56 dest #immed subtract w/carry ADD 57 dest #immed add ADC 58 dest #immed add w/carry INCD 69 dest_pair & register pair 16-bit source_pair increment CPD 66 dest_pair source_pair 16-bit compare Bytes 3 3 3 3 3 3 3 3 3 2 2 3 3 3 3 3 3 3 3 3 2 3 Cycles +Cycles/Waitstate 6 3 6 3 6 6 6 6 6 6 6 5 5 5 5 5 5 5 5 5 5 5 8 10 3 3 3 3 3 3 3 2 2 3 3 3 3 3 3 3 3 3 2 3 MISCELLANEOUS Group Instructions Instruction NOP CLC STC CMC CLI STI WDC Opcode 00 01 02 03 04 05 06 Operand 1 Operand 2 Description no operation clear carry set carry complement carry disable interrupts enable interrupts enable/restart Watchdog timer Bytes 1 1 1 1 1 1 1 Cycles 2 2 2 2 2 2 2 +Cycles/Waitstate 1 1 1 1 1 1 1 36 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Special Functions Registers (SFRs) Summary Address FF FE FD FC FB FA F9 F8 F7 F6 F5 F4 F3 F2 F1 F0 EF EE ED EC EB EA E9 E8 E7 E6 E5 E4 E3 E2 E1 E0 DF DE DD DC DB DA D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 CF CE R/W R/W R/W R/W R/W W R R/W R/W R/W R/W R/W W R W R R/W R/W W R R/W W R W R R/W W R R/W R/W R/W R/W R/W R/W R R/W R/W R/W R R/W R/W R/W R R/W W R R/W W R/W R/W R/W R/W W R R/W R/W R/W R/W R/W W Name flags ***** irq * imr **** bank RESERVED sysStat dac RESERVED RESERVED stkData stkNdx RESERVED adcSampleHi RESERVED adcSampleLo RESERVED RESERVED RESERVED RESERVED RESERVED anCtl *** Reset Bit 7 0000 0000 carry 0000 0000 MTtimer 0000 0000 MTtimer 1110 0000 ws2 0000 0000 0000 0000 0 dh7 Bit 6 zero p0.2 p0.2 ws1 Bit 5 sign block block ws0 Bit 4 Bit 3 Bit 2 trap stkoflo stkfull timer3 p0.0 endmark timer3 p0.0 endmark (bank4) bank3 bank2 wd_on dh4 0 dh3 0 dh2 Bit 1 --timer2 timer2 bank1 fastClk dh1 Bit 0 gie timer1 timer1 bank0 0 dh0 brownout wd_timed dh6 dh5 0000 0000 0000 0000 0000 0000 0000 0000 stdk7 0 adc15 adc07 stkd6 0 adc14 adc06 stkd5 stkind5 adc13 adc05 stkd4 stkind4 adc12 adc04 stkd3 stkind3 adc11 adc03 stkd2 stkind2 adc10 adc02 stkd1 stkind1 adc09 adc01 stkd0 stkind0 adc08 adc00 0000 0000 -anctlen 0 lsb1 0000 0000 -anctlen 0 lsb1 t2v ** 0000 0000 x x x 0000 0000 t2v7 t2v6 t2v5 t2r 0000 0000 t2r7 t2r6 t2r5 t1v ** 0000 0000 x x x 0000 0000 t1v7 t1v6 t1v5 t1r 0000 0000 t1r7 t1r6 t1r5 wake1 0000 0000 w1.7 w1.6 w1.5 wake0 0000 0000 w0.7 w0.6 w0.5 ckCtl **** 0000 1000 pdn t2wake fclk_on p0CtlB 0000 0000 ctlb0.7 ctlb0.6 ctlb0.5 p0CtlA 0000 0000 ctla0.7 ctla0.6 ctla0.5 p0In xxxx xxxx pin0.7 pin0.6 pin0.5 p0Out 0000 0000 pout0.7 pout0.6 pout0.5 p1CtlB 0000 0000 ctlb1.7 ctlb1.6 ctlb1.5 p1CtlA 0000 0000 ctla1.7 ctla1.6 ctla1.5 p1In xxxx xxxx pin1.7 pin1.6 pin1.5 p1Out 0000 0000 pout1.7 pout1.6 pout1.5 p2CtlB 0000 0000 ctlb2.7 ctlb2.6 ctlb2.5 p2CtlA 0000 0000 ctla2.7 ctla2.6 ctla2.5 p2In xxxx xxxx pin2.7 pin2.6 pin2.5 p2Out 0000 0000 pout2.7 pout2.6 pout2.5 t3v ** 0000 0000 x x x 0000 0000 t3v7 t3v6 t3v5 t3r 0000 0000 t3r7 t3r6 t3r5 t3Ctl 0000 0000 t3_on polarity p0.1_src pwmData 0000 0000 pwmd09 pwmd08 pwmd07 pwmCtl 0000 0000 pwmd01 pwmd00 tenBits clkExt **** 0000 0000 rom_0Ws MTclk_on movx_4ws sysCtl 0000 0000 wd_ps1 wd_ps0 brnout_on cmpCtl 1100 0000 1 1 0 1100 0000 compA+ compB+ 0 cmpRef 0000 0000 0 0 0 extAdd 0000 0000 0 0 cb1 RESERVED RESERVED flagsHold 0000 0000 carry zero sign ***** awcCtl 0000 0000 pwrl 0 thrh2 lsb0 lsb0 x t2v4 t2r4 x t1v4 t1r4 w1.4 w0.4 clk_div1 ctlb0.4 ctla0.4 pin0.4 pout0.4 ctlb1.4 ctla1.4 pin1.4 pout1.4 ctlb2.4 ctla2.4 pin2.4 pout2.4 x t3v4 t3r4 t3_gated pwmd06 0 L1clk_on afe_g1 0 0 0 rw d2a_half rc_osc2 0 afe_on d2a_half rc_osc2 0 afe_on x x x x t2v3 t2v2 t2v1 t2v0 t2r3 y2r2 t2r1 t2r0 x x x x t1v3 t1v2 t1v1 t1v0 t1r3 t1r2 t1r1 t1r0 w1.3 w1.2 w1.1 w1.0 w0.3 w0.2 w0.1 w0.0 clk_div0 slow_pclk osc2_on osc1_off ctlb0.3 ctlb0.2 ctlb0.1 ctlb0.0 ctla0.3 ctla0.2 ctla0.1 ctla0.0 pin0.3 pin0.2 pin0.1 pin0.0 pout0.3 pout0.2 pout0.1 pout0.0 ctlb1.3 ctlb1.2 ctlb1.1 ctlb1.0 ctla1.3 ctla1.2 ctla1.1 ctla1.0 pin1.3 pin1.2 pin1.1 pin1.0 pout1.3 pout1.2 pout1.1 pout1.0 ctlb2.3 ctlb2.2 ctlb2.1 ctlb2.0 ctla2.3 ctla2.2 ctla2.1 ctla2.0 pin2.3 pin2.2 pin2.1 pin2.0 pout2.3 pout2.2 pout2.1 pout2.0 x x x x t3v3 t3v2 t3v1 t3v0 t3r3 t3r2 t3r1 t3r0 t3_ps3 t3_ps2 t3_ps1 t3_ps0 pwmd05 pwmd04 pwmd03 pwmd02 period1 period0 0 pwm_on t1_ps3 t1_ps2 t1_ps1 t1_ps0 afe_g0 0 p02Edge p00Edge mux_sel ccs2 ccs1 ccs0 mux_sel ccs2 ccs1 ccs0 crv03 crv02 crv01 crv00 eda19 eda18 eda17 eda16 trap thrh1 0 thrh0 0 thrl2 0 thrl1 gie thrl0 37 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Address R/W R CD CC CB CA C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 W R Name Reset 0000 0000 Bit 7 pwrl Bit 6 detect Bit 5 thrh2 Bit 4 thrh1 Bit 3 thrh0 Bit 2 thrl2 Bit 1 thrl1 Bit 0 thrl0 RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED Reset: "x" = unknown/don't care, `-` = not implemented * Only "0" can be written to "irq" bits. "1" is a "nop" for the bit to which it is written. When using Sensory Speech technology, always write "1" to "block" and "endmark" in the "irq" register to avoid conflicting with technology code control of these bits. ** Write value is ignored and reload register value is written instead. *** -anctlen (Bit7) of values written to the "anCtl" register must be "0" to enable writing the other bits in the value to "anCtl". **** When using Sensory Speech technology, "fclk_on", "L1clk_on", and "block" and "endmark" in the "imr" register should be left at the values programmed by the technology code. A read-modify-write action should be used to modify the registers to avoid changing these bits. ***** "trap" must always be written as "0" in the "flags" and "flagsHold" registers 38 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 DC Characteristics Operating Conditions (TO = 0C to +70C, VDD = 2.4V - 3.6V) SYMBOL VIL VIH IIL IACT IACT IIDLE ISLEEP RPU PARAMETER Input Low Voltage Input High Voltage Input Leakage Current Supply Current, Active Supply Current, Active Supply Current, Idle Supply Current, Sleep Pull-up resistance P0.0-P0.7, P1.0-P1.7, P2.0- P2.7 A0-A19, D0-D7, PLLEN, -RESET, -RDR, -RDF, -WRC, -WRD -XM, PWM0, PWM1 Pull-down resistance TEST Output Low Current A0-A19, D0-D7, -RDR, -RDF, -WRC, -WRD, PDN P0.0-P0.7, P1.0-P1.7, P2.0-P2.7 PWM0, PWM1 Output High Current A0-A19, D0-D7, -RDR, -RDF, -WRC, -WRD, PDN P0.0-P0.7, P1.0-P1.7, P2.0-P2.7 PWM0, PWM1 MIN -0.1 0.8*Vdd TYP MAX 0.75 Vdd+0.3 10 20 7 4 UNITS V V A mA mA A A k k k k mA TEST CONDITIONS <1 10 4 1 10, 200, Hi-Z 100 10 10 Vss 4 8 180 -2.5 -5 -80 VOL = 0.5V, VDD = 2.4V VOL = 0.5V, VDD = 2.4V VOL = 0.8V, VDD = 3.3V VOH = 1.8V, VDD = 2.4V VOH = 1.8V, VDD = 2.4V VOH = 2.5V, VDD = 3.3V mA mA mA mA mA IOH A.C. Characteristics (External memory accesses) Operating Conditions (TO = 0C to +70C, VDD = 3.3V; load capacitance for outputs = 30pF) SYMBOL 1/TCL1 TRLRH TRLAV TALRAX TRAVDV TRHDX TWLWH TAVWL TALWAX TWDVAV TWHQX PARAMETER Processor Clock frequency -RDR (-RDF) Pulse Width -RDR (-RDF) Low to Address valid Address hold after -RDR (-RDF) Address valid to Valid Data In Data Hold after -RDR (-RDF) -WRC (-WRD) Pulse Width Address Valid to -WRC (-WRD) Address Hold after -WRC (-WRD) Write Data Valid to Address Valid Data Hold after -WRC (-WRD) PCLK=CLK1/1, 1WS MIN MAX PCLK=CLK1/1, 0WS MIN MAX UNITS MHz ns ns ns ns ns ns ns ns ns ns 14.32 140 5 0 135 0 140 35 35 5 35 35 35 35 0 14.32 140 5 0 65 70 5 39 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Timing Diagrams Note that the -RDR signal does not necessarily pulse for every read from code space, but may stay low for multiple cycles. -RDF (-RDR) TRLRH ADDRESS TRLAV TALRAX DATA TRAVDV TRHDX -WRC (-WRD) TWLWH ADDRESS TAVWL TALWAX DATA TWDVAV TWHQX External Read Timing External Write Timing Absolute Maximum Ratings Any pin to GND: Storage temperature: Operating temperature: Soldering temperature: Power dissipation: -0.1V to +4.0V -65C to +150C -40C to +85C 260C for 10 sec 1W WARNING: Stressing the RSC-4128 beyond the "Absolute Maximum Ratings" may cause permanent damage. These are stress ratings only. Operation beyond the "Operating Conditions" is not recommended and extended exposure beyond the "Operating Conditions" may affect device reliability. 40 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 Package Options The RSC-4128 can be purchased in 100-lead LQFP or 64 lead LQFP packages, or in unpackaged die. When using an in circuit emulator (ICE) on dice applications, a COB bonding pad ring equivalent to a 100-lead LQFP footprint is advised for easy ICE adapter attachment. DIE 100 1 82 NC P0.1 NC P0.2 P0.3 NC VDD PWM1 PWM0 GND NC P0.4 P0.5 NC P0.6 NC 64-lead LQFP A0 P0.1 NC NC A1 100-lead LQFP PWM1 PWM0 NC VDD GND NC P0.4 P0.5 NC P0.2 A2 NC P0.3 A3 NC A5 A6 P0.6 78 77 NC 76 75 74 73 72 71 70 69 68 67 A4 RSC-4128 (100 pad DIE) L ogo 29 30 52 53 P0.0 NC PDN GND XO1 XI1 VDD XO2 XI2 P2.7 NC GND VDD P2.6 P2.5 RESET_ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RSC-4128 (64-lead LQFP) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P0.7 NC P1.0 VDD GND P1.1 NC P1.2 P1,3 P1.4 P1.5 VDD GND P1.6 P1.7 PLLEN P0.0 D7 D6 PDN D5 D4 GND XO1 XI1 VDD -XM XO2 XI2 D3 D2 P2.7 D1 D0 GND VDD P2.6 RESERVED 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 82 81 99 98 97 96 95 94 93 92 91 90 89 80 79 88 87 86 85 84 83 P0.7 A7 A8 P1.0 A9 VDD GND A10 P1.1 A11 P1.2 A12 P1.3 A13 P1.4 A14 P1.5 A15 VDD GND P1.6 A16 P1.7 A17 PLLEN RSC-4128 (100-lead LQFP) 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DACOUT AVSS VCM MICIN2 MICIN1 MICGND VREF AVDD P2.4 P2.3 P2.2 P2.1 P2.0 GND VDD TEST 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P2.5 RESERVED -RESET AMPCOM VREF MICIN2 MICIN1 DACOUT AVSS VCM AVDD NC DIE 64 LQFP 100 LQFP Pad # Pin # Pin # 1 1 1 2 2=NC 2 3 3 4 3 4 5 5 6 6 7 4 7 8 4 7 9 5 8 10 6 9 11 7 10 12 7 10 13 11 14 8 12 15 9 13 16 14 17 15 18 10 16 19 11=NC 17 20 18 21 12 19 22 12 19 23 13 20 24 13 20 25 14 21 26 22 27 15 23 28 24 29 16 25 30 17 26 31 18 27 32 19 28 33 20 29 34 21 30 Pin Name Description P0.0 D7 D6 PDN D5 D4 GND GND XO1 XI1 VDD VDD -XM XO2 XI2 D3 D2 P2.7 D1 D0 GND GND VDD VDD P2.6 reserved P2.5 reserved -RESET DACOUT AVSS VCM MICIN2 MICIN1 General Purpose I/O that can act as a "wake-up" input External Data Bus (no connect for 64-lead LQFP) External Data Bus Power Down (active high when powered down) External Data Bus External Data Bus Ground Ground Oscillator 1 output Oscillator 1 input Supply Voltage Supply Voltage External Memory Enable (active low) Oscillator 2 output Oscillator 2 input External Data Bus External Data Bus General Purpose I/O that can act as a "wake-up" input External Data Bus (no connect for 64-lead LQFP) External Data Bus Ground Ground Supply Voltage Supply Voltage General Purpose I/O that can act as a "wake-up" input DO NOT USE General Purpose I/O that can act as a "wake-up" input DO NOT USE Reset (active low) DAC output Analog ground Common mode reference Microphone input for audio wakeup Microphone input Signal Type I/O, 10k or 200k pull-up resistor; high-Z I/O, 100k pull-up; high-Z I/O, 100k pull-up; high-Z Output I/O, 100k pull-up; high-Z I/O, 100k pull-up; high-Z GND GND Output Input PWR PWR Input, 10k pull-up resistor Output Input I/O, 100k pull-up; high-Z I/O, 100k pull-up; high-Z I/O, 10k or 200k pull-up resistor; high-Z I/O, 100k pull-up; high-Z I/O, 100k pull-up; high-Z GND GND PWR PWR I/O, 10k or 200k pull-up resistor; high-Z DO NOT USE I/O, 10k or 200k pull-up resistor; high-Z DO NOT USE Input, 100k pull-up resistor Analog out (A) GND Analog Analog IN Analog IN 41 P/N 80-0206-H (c) 2004 Sensory Inc. -WRC A19 -WRD -RDR A18 TEST P2.4 P2.3 P2.2 GND P2.1 P2.0 GND VDD -RDF NC RSC-4128 DIE 64 LQFP 100 LQFP Pad # Pin # Pin # 35 22 31 36 23 32 37 24 33 34 38 25 35 39 26 36 37 40 27 38 41 39 42 28 40 43 29 41 44 30 42 45 31 43 46 44 47 45 48 46 49 47 50 48 51 49 52 32 50 53 33 51 54 52 55 34 53 56 54 57 35 55 58 36 56 59 36 56 60 37 57 61 37 57 62 58 63 38 59 64 60 65 39 61 66 62 67 40 63 68 64 69 41 65 70 42=NC 66 71 43 67 72 68 73 44 69 74 44 69 75 45 70 76 45 70 77 71 78 46 72 79 73 80 47=NC 74 81 48 75 49=NC 76 82 50 77 83 78 51=NC 79 84 52 80 85 81 82 86 53 83 87 84 54=NC 85 88 55 86 89 55 86 90 56 87 91 57 88 92 58 89 93 58 89 59=NC 90 94 91 Pin Name Description AMPCOM VREF AVDD NC P2.4 P2.3 NC P2.2 GND P2.1 P2.0 GND VDD -RDF -WRD -RDR -WRC A19 A18 TEST PLLEN A17 P1.7 A16 P1.6 GND GND VDD VDD A15 P1.5 A14 P1.4 A13 P1.3 A12 P1.2 A11 P1.1 A10 GND GND VDD VDD A9 P1.0 A8 A7 P0.7 NC P0.6 A6 NC P0.5 A5 NC P0.4 A4 NC GND GND PWM0 PWM1 VDD VDD NC A3 Amplifier input common Voltage reference Analog Supply Voltage Not connected General Purpose I/O or comparator input General Purpose I/O or comparator input Not connected General Purpose I/O or comparator reference Ground General Purpose I/O or comparator input General Purpose I/O or comparator input Ground Supply Voltage External Data Read Strobe (active low) External Data Write Strobe (active low) External Code Read Strobe (active low) External Code Write Strobe (active low) External Memory Address Bus External Memory Address Bus Test Mode PLL Enable External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus General Purpose I/O that can act as a "wake-up" input Ground Ground Supply Voltage Supply Voltage External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus (NC for 64-lead LQFP) General Purpose I/O that can act as a "wake-up" input External Memory Address Bus Ground Ground Supply Voltage Supply Voltage External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus External Memory Address Bus (NC for 64-lead LQFP) General Purpose I/O that can act as a "wake-up" input Not connected General Purpose I/O that can act as a "wake-up" input External Memory Address Bus (NC for 64-lead LQFP) Not connected General Purpose I/O that can act as a "wake-up" input External Memory Address Bus Not connected General Purpose I/O that can act as a "wake-up" input External Memory Address Bus (NC for 64-lead LQFP) Not connected Ground Ground Pulse Width Modulator Output 0 Pulse Width Modulator Output 1 Supply Voltage Supply Voltage Not connected External Memory Address Bus (NC for 64-lead LQFP) Signal Type Analog IN Analog OUT (A) PWR Data Sheet I/O, 10k or 200k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z GND I/O, 10k or 200k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z GND PWR Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Input, 10k pull-down resistor Input, 100k pull-up resistor Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z GND GND PWR PWR Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z GND GND PWR PWR Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z GND GND Output; 10k pull-up resistor; high-Z Output; 10k pull-up resistor; high-Z PWR PWR Output, 100k pull-up resistor; high-Z 42 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet DIE 64 LQFP 100 LQFP Pad # Pin # Pin # 95 60 92 93 96 94 97 61 95 98 96 62=NC 97 99 63 98 100 99 64=NC 100 Pin Name Description P0.3 NC A2 P0.2 A1 NC P0.1 A0 NC General Purpose I/O that can act as a "wake-up" input Not connected External Memory Address Bus General Purpose I/O that can act as a "wake-up" input External Memory Address Bus (NC for 64-lead LQFP) Not connected General Purpose I/O that can act as a "wake-up" input External Memory Address Bus (NC for 64-lead LQFP) Not connected Signal Type RSC-4128 I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z I/O, 10k or 200k pull-up resistor; high-Z Output, 100k pull-up resistor; high-Z 43 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Die Pad Ring PWM1 PWM0 P0.6 A6 P0.5 A5 P0.4 A4 GND GND VDD VDD A3 P0.3 A2 P0.2 A1 P0.1 100 99 98 97 96 95 94 93 92 P0.0 1 D7 2 D6 3 PDN 4 D5 5 D4 6 GND 7 GND 8 XO1 9 XI1 10 VDD 11 VDD 12 -XM 13 XO2 14 XI2 15 D3 16 D2 17 P2.7 18 D1 19 D0 20 GND 21 GND 22 VDD 23 VDD 24 P2.6 25 reserved 26 P2.5 27 reserved 28 -reset 29 A0 91 90 89 88 87 86 85 84 83 82 81 P0.7 80 A7 79 A8 78 P1.0 77 A9 76 VDD 75 VDD 74 GND 73 GND 72 A10 71 P1.1 70 A11 69 P1.2 68 A12 67 P1.3 66 A13 65 P1.4 64 A14 63 P1.5 62 A15 61 VDD 60 VDD 59 GND 58 GND 57 P1.6 56 A16 55 P1.7 54 A17 53 PLLEN 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 TEST A18 A19 -WRC -RDR -WRD -RDF VDD GND P2.0 P2.1 GND P2.2 P2.3 P2.4 AVDD VREF AMPCOM MICIN1 MICIN2 VCM AVSS DACOUT 44 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 RSC-4128 Die Bonding Pad Locations PAD # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PADNAME X (um) Y (um) P0.0 D7 D6 PDN D5 D4 GND GND XO1 XI1 VDD VDD -XM XO2 XI2 D3 D2 P2.7 D1 D0 GND GND VDD VDD P2.6 reserved P2.5 reserved -RESET 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 4564 4412 4260 4107 3955 3803 3651 3498 3346 3251 3063 2858 2729 2605 2510 2376 2238 2095 1943 1790 1667 1434 1282 1129 964 825 672 520 368 PAD # 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 PADNAME X (um) Y (um) DACOUT AVSS VCM MICIN2 MICIN1 AMPCOM VREF AVDD P2.4 P2.3 P2.2 GND P2.1 P2.0 GND VDD -RDF -WRD -RDR -WRC A19 A18 TEST 447 542 637 732 827 922 1017 1112 1364 1459 1554 1649 1744 1839 1934 2029 2124 2219 2314 2409 2504 2599 2694 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 95 PAD # 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 PADNAME X (um) Y (um) PLLEN A17 P1.7 A16 P1.6 GND GND VDD VDD A15 P1.5 A14 P1.4 A13 P1.3 A12 P1.2 A11 P1.1 A10 GND GND VDD VDD A9 P1.0 A8 A7 P0.7 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 2965 368 516 665 813 961 1110 1291 1446 1681 1831 1972 2104 2237 2366 2481 2596 2708 2817 3061 3194 3358 3513 3678 3827 3975 4123 4272 4420 4568 PAD # 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 PADNAME X (um) Y (um) P0.6 A6 P0.5 A5 P0.4 A4 GND GND PWM0 PWM1 VDD VDD A3 P0.3 A2 P0.2 A1 P0.1 A0 2694 2599 2504 2409 2314 2219 2124 2029 1792 1366 1128 1033 938 843 748 653 558 463 368 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 4880 Notes: 1. Coordinates are in microns (um), rounded to nearest um. 2. Coordinates are of the center of the bonding pad opening (70um). 3. Coordinate (0,0) is the lower left corner of the die. 4. Die size with scribe and seal ring is 3060 um x 4975 um. 5. No external die substrate tie is required. However, a substrate tie to ground is preferred. 45 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Mechanical Data LQFP 100 PLASTICQUAD FLATPACK (14x14x1.4 mm) Symbol A A1 A2 b b1 c c1 D D1 E E1 L L1 R1 R2 S 1 2 3 Dimension in mm Min Nom Max 1.60 0.05 0.15 1.35 1.40 1.45 0.17 0.22 0.27 0.17 0.20 0.23 0.09 0.20 0.09 0.16 15.85 16.00 16.15 13.90 14.00 14.10 15.85 16.00 16.15 13.90 14.00 14.10 0.50 BSC 0.45 0.60 0.75 1.00 REF 0.08 0.08 0.20 0.20 0 3.5 7 0 12 TYP 12 TYP Dimension in inch Min Nom Max 0.063 0.002 0.006 0.053 0.055 0.057 0.007 0.009 0.011 0.007 0.008 0.009 0.004 0.008 0.004 0.006 0.624 0.630 0.636 0.547 0.551 0.555 0.624 0.630 0.636 0.547 0.551 0.555 0.20 BSC 0.018 0.024 0.030 0.039 BSC 0.003 0.003 0.008 0.008 0 3.5 7 0 12 TYP 12 TYP Notes: A. B. C. All linear dimensions are in millimeters. This drawing is subject to change without notice. Falls within JEDEC MS-026 BBC 46 P/N 80-0206-H (c) 2004 Sensory Inc. Data Sheet RSC-4128 LQFP 64 PLASTICQUAD FLATPACK (10x10x1.4 mm) Symbol A A1 A2 b b1 c c1 D D1 E E1 L L1 R1 R2 S 1 2 3 Dimension in mm Min Nom Max 1.60 0.05 0.15 1.35 1.40 1.45 0.17 0.22 0.27 0.17 0.20 0.23 0.09 0.20 0.09 0.16 12.00 BSC 10.00 BSC 12.00 BSC 10.00 BSC 0.50 BSC 0.45 0.60 0.75 1.00 REF 0.08 0.08 0.20 0.20 0 3.5 7 0 12 TYP 12 TYP Dimension in inch Min Nom Max 0.063 0.002 0.006 0.053 0.055 0.057 0.007 0.009 0.011 0.007 0.008 0.009 0.004 0.008 0.004 0.006 0.472 BSC 0.394 BSC 0.472 BSC 0.394 BSC 0.20 BSC 0.018 0.024 0.030 0.039 BSC 0.003 0.003 0.008 0.008 0 3.5 7 0 12 TYP 12 TYP Notes: D. E. F. All linear dimensions are in millimeters. This drawing is subject to change without notice. Falls within JEDEC MS-026, BBC 47 P/N 80-0206-H (c) 2004 Sensory Inc. RSC-4128 Data Sheet Ordering Information Part RSC-4128 Die RSC-4128 64LQFP RSC-4128 100LQFP Shipping P/N (ROM specific) (ROM specific) (ROM specific) Description Tested, Singulated RSC-4128 die in waffle pack RSC-4128 64 pin 10 x 10 x 1.4 mm LQFP RSC-4128 100 pin 14 x 14 x 1.4 mm LQFP 48 P/N 80-0206-H (c) 2004 Sensory Inc. The Interactive SpeechTM Product Line The Interactive Speech line of ICs and software was developed to "bring life to products" through advanced speech recognition and audio technology. The Interactive Speech Product Line was designed for consumer telephony products and cost-sensitive consumer electronic applications such as home electronics, personal security, and personal communication. The product line includes award-winning RSC series general-purpose microcontrollers and tools, SC series of speech microcontrollers, plus a line of easy-to-implement chips that can be pin-configured or controlled by an external host microcontroller. Sensory's software technologies run on a variety of microcontrollers and DSPs. RSC Microcontrollers and Tools The RSC product line contains low-cost 8-bit speech-optimized microcontrollers designed for use in consumer electronics. All members of the RSC family are fully integrated and include A/D, pre-amplifier, D/A, ROM, and RAM circuitry. The RSC family can perform a full range of speech/audio functions including speech recognition, speaker verification, speech and music synthesis, and voice record/playback. The family is supported by a complete suite of evaluation tools and development kits. SVC Microcontrollers and Tools The SVC product line combines text-dependent speaker verification password biometrics with low-cost 8-bit microcontrollers designed for use in consumer electronics. All members of the SVC family are fully integrated for speech applications and include A/D, preamplifier, D/A, ROM, and RAM circuitry. The SVC family performs noise robust speaker verification password security functions and speech synthesis. The family is supported by a complete suite of evaluation tools and development kits. SC Microcontrollers and Tools The SC-6x product line feature the highest quality speech synthesis ICs at the lowest data rate in the industry. The line includes a 12.32 MIPS processor for high-quality low data-rate speech compression and MIDI music synthesis, with plenty of power left over for other processor and control functions. Members of the SC-6x line can store as much as 37 minutes of speech on chip and include as much as 64 I/O pins for external interfacing. Integrating this broad range of features onto a single chip enables developers to create products with high quality, long duration speech at very competitive price points. Application Specific Standard Products (ASSPs) Voice DirectTM II provides inexpensive speaker-dependent speech recognition and speech synthesis. This easy-to-use, pinconfigurable chip requires no custom programming and can recognize up to 15 words in 4 pin-programmable modes. Ideal for speaker-dependent command and control of household consumer products, Voice DirectTM II is part of a complete product line that includes the IC, module, and Voice DirectTM II Speech Recognition Kit. Voice ExtremeTM simplifies the creation of fully custom speech-enabled products by offering developers the capability of programming the chip in a high-level C-like language. Program code, speech data, and even record and playback information can be stored on a single off-chip Flash memory. Based on Sensory's RSC-364 speech processor, Voice Extreme includes a highly efficient on-chip code interpreter, and is supported by a comprehensive suite of low-cost development tools. Software and Technology Voice ActivationTM micro footprint software provides advanced speech technology on a variety of microcontroller and DSP platforms. A flexible design with a broad range of technologies allows manufacturers to easily integrate speech functionality into consumer electronic products. Fluent SpeechTM small footprint software recognizes up to 50,000 words; offers Animated Speech with the ability to automate enunciation and articulation; performs text-to-speech synthesis in either male or female voices; provides noise and echo cancellation, performs word spotting for natural language usage; offers telephone barge-in; and provides continuous digit recognition. Important notices Reasonable efforts have been made to verify the accuracy of information contained herein, however no guarantee can be made of accuracy or applicability. Sensory reserves the right to change any specification or description contained herein. 1991 Russell Ave., Santa Clara, CA 95054 Tel: (408) 327-9000 Fax: (408) 727-4748 (c) 2004 SENSORY, INC. ALL RIGHT RESERVED. Sensory is registered by the U.S. Patent and Trademark Office. All other trademarks or registered trademarks are the property of their respective owners. www.sensoryinc.com |
Price & Availability of RSC4128 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |