View HA12209_845028.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HA12209F
Audio Signal Processor for Cassette Deck (Dolby B-type NR with Recording System)
ADE-207-221A (Z) 2nd Edition Jun. 1999 Description
HA12209F is silicon monolithic bipolar IC providing Dolby noise reduction system*, music sensor system, REC equalizer system and each electronic control switch in one chip.
Functions
* Dolby B-NR * REC equalizer * Music sensor x 2 channel x 2 channel x 1 channel
* Each electronic control switch to change REC equalizer, bias, etc.
Features
* REC equalizer is very small number of external parts and have 4 types of frequency characteristics built-in. * 2 types of input for PB, 1 type of input for REC. * 70-PB equalizer changing system built-in. * Dolby NR with dubbing double cassette decks. Unprocessed signal output available from recording out terminals during PB mode. * Provide stable music sensor system, available to design music sensing time and level. * Controllable from direct micro-computer output. * Bias oscillator control switch built-in. * NR ON/OFF and REC/PB fully electronic control switching built-in. * Normal-speed/high-speed, TYPE I/TYPE II and PB equalizer fully electronic control switching built-in. * Available to reduce substrate-area because of high integration and small external parts. * Dolby is a trademark of Dolby Laboratories Licensing Corporation. A license from Dolby Laboratories Licensing Corporation is required for the use of this IC.
HA12209F
Ordering Information
Standard Level
Operating Voltage Product HA12209F Package FP-56 PB-OUT Level 580mVrms REC-OUT Level Dolby Level 300mVrms 300mVrms Min 10V Max 15V
Function
Product HA12209F Dolby B-NR REC-EQ Music Sensor REC/PB Selection
Note: Depending on the employed REC/PB head and test tape characteristics, there is a rare case that the REC-EQ characteristics of this LSI can not be matched to the required characteristics because of built-in resistors which determined the REC-EQ parameters in this case, please inquire the responsible agent because the adjustment of built-in resistor is necessary.
Rev.2, Jun. 1999, page 2 of 49
HA12209F
Pin Description, Equivalent Circuit (VCC=12V, Ta=25C, No signal, The value in the table show typical value.)
Pin No. 52 Pin Name AIN (R) Note V = VCC / 2 Equivalent Circuit Pin Description PB A deck input
V 100k VCC/2
48 54 45 56 44 6 37 4
AIN (L) BIN (R) BIN (L) RIN (R) RIN (L) EQIN (R) EQIN (L) DET (R) V = 2.6V
VCC
PB B deck input
REC input
REC equalizer input
Time constant pin for Dolby-NR
V
GND
39 49 1
DET (L) RIP BIAS1 V = VCC / 2 V = 0.6V Ripple filter Dolby bias current input
V
GND
42
BIAS2
V = 1.3V
REC equalizer bias current input
V
GND
Rev.2, Jun. 1999, page 3 of 49
HA12209F
Pin Description, Equivalent Circuit (VCC=12V, Ta=25C, No signal, The value in the table show typical value.) (cont)
Pin No. 3 Pin Name PBOUT (R) Note V = VCC / 2 Equivalent Circuit
VCC
Pin Description PB output
V
GND
40 5 38 8 35 32 53
PBOUT (L) RECOUT (R) RECOUT (L) EQOUT (R) EQOUT (L) MAOUT ABO (R) V = VCC / 2
VCC
REC output
Equalizer output
1
MS amp. input * Time constant pin for PB equalizer
V 15k 12k
GND
46 25
ABO (L) BIAS (C) V = VCC - 0.7
VCC
REC bias current output
V
26 Note:
BIAS (N) 1. MS : Music Sensor
Rev.2, Jun. 1999, page 4 of 49
HA12209F
Pin Description, Equivalent Circuit (VCC=12V, Ta=25C, No signal, The value in the table show typical value.) (cont)
Pin No. 29 Pin Name MSDET Note I = 0A
I V
Equivalent Circuit
VCC
Pin Description Time constant 1 pin for MS *
GND
31
MSIN
V = VCC / 2
VCC
MS input
V 100k VCC/2
33
MAI
V = VCC / 2
MAOUT VCC 100k V 45k VCC/2
MS amp. output
27
MSOUT
I = 0A
V
VCC I
MS output (to MPU)
DGND
Note:
1. MS : Music Sensor
Rev.2, Jun. 1999, page 5 of 49
HA12209F
Pin Description, Equivalent Circuit (VCC=12V, Ta=25C, No signal, The value in the table show typical value.) (cont)
Pin No. 10 Pin Name PB A/B Note I = 20A
I V 22k
Equivalent Circuit
Pin Description Mode control input
100k GND
11 12 14 16 17 19 20 21 22, 23 50, 51
A 120/70 NORM/HIGH B 120/70 BIAS ON/OFF RM ON/OFF NR ON/OFF REC/PB LM ON/OFF VCC GND V = VCC V = 0V Power supply GND pin No connection
2, 7, 9, 13, NC 15, 18, 24, 28, 30, 34, 36, 41, 43, 47, 55
Rev.2, Jun. 1999, page 6 of 49
HA12209F
Block Diagram
RECOUT (L) EQOUT (L) PBOUT (L)
EQIN (L)
MAOUT
MSDET
DET (L)
BIAS2
MSIN
MAI
NC
NC
NC
NC
+ + 42 NC RIN (L) BIN (L) ABO (L) NC AIN (L) RIP 43 44 45 15k 46 12k 47 48 49 + 50 51 AIN (R) ABO (R) BIN (R) NC RIN (R) 52 15k 53 54 55 56 1 2 3 4 5 + 6 + EQ 7 8 + 9 10 11 12 13 14 12k 18 17 16 15 NC RM /OFF DOLBY B-NR LPF 21 20 19 LM ON/ REC/ NR ON/ DOLBY B-NR 45k 24 23 VCC 22
+ - +
+ 39 38
+ 37 36 EQ
+ 35 34 33 32 31 30 29 28 100k MS DET 27 26 25 MSOUT BIAS (N) NC
41
40
BIAS SW
BIAS (C) NC
BIASOUT
BIAS ON/ NC
PBOUT (R)
DET (R)
RECOUT (R)
EQIN (R)
EQOUT (R)
PB /B
BIAS1
/HIGH
NC
NC
NC
NC
/70
A
Rev.2, Jun. 1999, page 7 of 49
B
/70
HA12209F
Functional Description
Power Supply Range HA12209F is designed to operate on single supply. Table 1
Item Single Supply
Spply Voltage
Power Supply Range 10V to 15V
Note: The lower limit of supply voltage depends on the line output reference level. The minimum value of the overload margin is specified as 12dB by Dolby Laboratories.
Reference Voltage For this IC, the reference voltage (VCC/2) occurrence device is built-in as AC grand. A capacitor for a ripple filter is greatly small characteristic with 1/100 compared with conventional device. And, the reference voltage are provided for the left channel and the right channel separately. The block diagram is shown as figure 1.
22 23
VCC + - L channel Reference voltage
VCC
+ - Music sensor Reference voltage + - R channel Reference voltage 50 51 49 GND PIR + 1 Unit C:F
Figure 1 Reference Voltage
Rev.2, Jun. 1999, page 8 of 49
HA12209F
Operating Mode Control HA12209F provides fully electronic switching circuits. And each operating mode control is controlled by parallel data (DC voltage). Table 2
Pin No.
Control Voltage
Lo Hi 4.0 to 5.3 Unit V Test Condition
Input Pin Measure
10, 11, 12, 14, 16, -0.2 to 1.0 17, 19, 20, 21
Note:
1. Each pins are on pulled down with 100k internal resistor. Therefore, it will be low-level when each pins are open. 2. Over shoot level and under shoot level of input signal must be the standardized. (High: 5.3V, Low: -0.2V) 3. For reduction of pop noise, connect 1F to 22F capacitor with mode control pins. But it is impossible to reduce completely in regard to Line mute, therefore, use external mute at the same time.
Input Block Diagram and Level Diagram
MS
REF 5.7dB PBOUT 580mVrms
300mVrms AIN 21.3dB BIN 25.9mVrms FLAT (120) 0dB 70s PB REC
REC PB
300mVrms DOLBY B-NR PB/REC=0dB/17dB RECOUT 300mVrms
300mVrms
12k 15k ABO CEX1 42.4mVrms RIN Unit R: C:F
Note: The each level shown above is typical value when offering PBOUT level to PBOUT pin.
Figure 2 Input Block Diagram
Rev.2, Jun. 1999, page 9 of 49
HA12209F
PB Equalizer By switching logical input level of 11 pin (for Ain) and 14 pin (for Bin), you can equalize corresponding to tape position at play back mode. With the capacity CEX1 capacitance that we showed for figure 2 70 s by the way figure seem to 3 they are decided.
Gv
t1 = CEX1 * (12k + 15k) t2 = CEX1 * 15k f (t1) (t2)
Figure 3 Frequency Characteristic of PB Equalizer The sensitivity Adjustment of Music Sensor Adjusting MS amp. gain by external resistor, the sensitivity of music sensor can set up.
VCC REP C26 0.01 PB(L) MAI 100k 45k - + -6dB LPF 25kHz 100k DET MS AMP MS OUT Microcomputer GND MA OUT MSIN MS DET RL R12 330k + C10 0.33 DVCC
GND
Unit PB(R)
R: C:F
Figure 4 Music Sensor Block Diagram
Rev.2, Jun. 1999, page 10 of 49
HA12209F
The sensitivity of Music Sensor
Gv
f1 =
1 [Hz] 2 * C26 * 100k
f2 = 25k [Hz] f f1 f2
Figure 5 Frequency Characteristic of MSIN Occasion of the external component of figure 4, f1 is 159Hz. A standard level of MS input pin 25.9mVrms, therefore, the sensitivity of music sensor (S) can request it, by lower formulas.
A = MS Amp Gain B = PB input Gain x (1/2)*1 C = Sensed voltage 20log (A x B) = D [dB] PB input Gain = 21.3 [dB] S = 14 - D [dB] S = 20log C [dB] 25.9 * A * B
Note: 1. Case of one-sided channel input.
Time Constant of Detection Figure 6(1) generally shows that detection time is in proportion to value of capacitor C10. But, with 2 3 Attack* and Recovery* the detection time differs exceptionally.
Detection time
Detection time
Recovery
Attack
Detection time
Recovery
Recovery Attack
Attack C10
R12
Detection level
Input level
Function Characteristic of MS (1)
Function Characteristic of MS (2)
Function Characteristic of MS (3)
Figure 6 Function Characteristics of MS Like the figure 6(2), Recovery time is variably possible by value of resistor R12. But Attack time gets about fixed value. Attack time has dependence by input level. When a large signal is inputted, Attack time is short tendency. Note: 2. Attack : Non-music Music
3. Recovery : Music Non-music
Rev.2, Jun. 1999, page 11 of 49
HA12209F
Music Sensor Output (MSOUT) As for internal circuit of music sensor block, music sensor out pin is connected to the collector of NPN type directly, output level will be "high" when sensing no signal. And output level will be "low" when sensing signal. Connection with microcomputer, it is requested to use external pull up resistor (RL = 10k to 22k) Note: Supply voltage of MSOUT pin must be less than VCC voltage.
The Tolerances of External Components For Dolby NR precision securing, please use external components shown at figure 7. If leak-current are a few electrolytic-capacitor, it can be applicable to C2 and C15.
C15 0.1 10% 39 DET (L) HA12209 BIAS1 1 R1 33k 2% DET (R) 4 C2 0.1 10% Unit R: C:F
Figure 7 Tolerance of External Components
Low-Boost
+
+
EQIN REC EQ
EQOUT
CEX2 REX1 2.2 20k Vin REX2 6.8k REX3 5.1k
CEX4 0.47
+ CEX3 0.47 GND
Unit
R: C:F
Figure 8 Example of Low Boost Circuit
Rev.2, Jun. 1999, page 12 of 49
HA12209F
External components shown figure 8 gives frequency response to take 6dB boost. And cut off frequency can request it, by lower formulas.
Gv
f1 = f2 = f f1 f2
1 [Hz] 2 * CEX3 * (REX3 + R0) 1 [Hz] 2 * CEX3 * REX3 R0 = REX1 * REX2 [] REX1 + REX2
Figure 9 Frequency Characteristic of Low-Boost
Bias Switch This series built-in DC voltage generator for bias oscillator and its bias switches. External resistor R8, R10 which corresponded with tape positions and bias out voltage are relater with below.
Vbias = R9 x (VCC - 0.7) [V] (R10 or R8) + R9
Bias switch follows to a logic of 14 pin (B 120/70). Note: A current that flows at bias out pin, please use it less than 5mA.
R10 BIAS (N) 26 R8 BIAS (C) 25 R9 GND Vbias
Figure 10 External Components of Bias Block
Rev.2, Jun. 1999, page 13 of 49
HA12209F
Absolute Maximum Rating (Ta=25C)
Item Max supply voltage Power dissipation Operating temperature Storage temperature Symbol VCC max PT Topr Tstg Rating 16 500 -40 to +75 -55 to +125 Unit V mW C C Ta 75C Note
Rev.2, Jun. 1999, page 14 of 49
Item 120/ MUTE fin 70 (Hz) 120 ON No signal RECOUT Other level (dB)
Symbol
Min
Typ
Max
Unit
Test Condition IC Condition*1 REC/PB A/B NR ON/OFF PB A
Quiescent current Input AMP. gain
15.0
30.0
mA
IQ GV PB GV REC B type ENC 2k (1) Encode boost ENC 2k (2) ENC 5k (1) ENC 5k (2) Signal handling Vo max Signal to noise ratio S/N Total harmonic distortion T.H.D. CTRL (1) Channel separation CTRL (2) CT A/B Crosstalk CT R/P Mute attenuation MUTE 70 EQ gain GV EQ 1k GV EQ 10k MS sensing level*3 VON MS output low level VOL IOH MS output leak current Control voltage VIL VIH 28.5 24.2 5.8 10.0 4.7 9.7 -- -- 0.3 -- -- -- -- -- 27.0 23.8 -7.4 1.5 2.0 1.0 5.3 A/B PB REC A REC A REC A REC A REC A REC A REC A REC A A/B PB REC A A/B PB REC/PB A/B PB A PB A/B PB A/B PB A PB A PB A -- -- -- -- THD=1%*2 Rg=5.1k, CCIR/ARM 120 120 120 120 120 120 120 120 120 120 120 120 120 120 70 70 120 120 120 -- -- OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF -- -- dB dB dB dB dB dB dB dB % dB dB dB dB dB dB dB dB V A V V -- 1k 1k 2k 2k 5k 5k 1k 1k 1k 1k 1k 1k 1k 1k 1k 10k 5k -- -- -- -- -- 0 0 -20 -30 -20 -30 -- -- 0 +12 +12 +12 +12 +12 0 0 -- -- -- -- --
25.5 21.2 2.8 7.0 1.7 6.7 12.0 64.0 N 70.0 75.0 60.0 70.0 70.0 24.0 20.8 -15.4 -- -- -0.2 4.0
23.0 27.0 22.7 4.3 8.5 3.2 8.2 13.0 70.0 0.05 80.0 85.0 70.0 80.0 80.0 25.5 22.3 -11.4 1.0 -- -- -- OFF OFF OFF ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF -- --
Note: 1. Other IC condition : REC-MUTE OFF, TYPE I, Normal speed, Bias OFF
2. VCC=10V
Electrical Characteristics (Ta = 25C, VCC = 12V, Dolby Level = REC-OUT Level = 300mVrms = 0dB)
Rev.2, Jun. 1999, page 15 of 49
3. For inputting signal to one side channel
HA12209F
Item 58 -- dB dB % -- 0.5 12.5 0.2
Symbol
Min
Typ
Max
Unit
S/N (EQ)
HA12209F
Rev.2, Jun. 1999, page 16 of 49
Test Condition TAPE SPEED TYPE I NORM Rg=5.1k, A-WTG Filter TYPE I NORM f=1kHz, THD=1%, Vin=-26dBs=0dB TYPE I NORM f=1kHz, Vin=-26dBs 500 21.5 23.4 35.1 24.4 27.3 38.0 20.7 23.8 37.0 23.5 28.3 41.7 -- -- mV dB dB dB dB dB dB dB dB dB dB dB dB dB V mV RL=2.4k+270 100 TYPE I NORM No signal TYPE I NORM f=1kHz, Vin=-46dBs f=5kHz, Vin=-46dBs f=12.5kHz, Vin=-46dBs TYPE II NORM f=1kHz, Vin=-46dBs f=5kHz, Vin=-46dBs f=12.5kHz, Vin=-46dBs TYPE I HIGH f=2kHz, Vin=-46dBs f=10kHz, Vin=-46dBs f=25kHz, Vin=-46dBs TYPE II HIGH f=2kHz, Vin=-46dBs f=10kHz, Vin=-46dBs f=25kHz, Vin=-46dBs TYPE I NORM f=1kHz, Vin=-14dBs RL=2.4k+270 0 20.0 21.4 32.1 22.9 25.3 35.0 19.2 21.8 34.0 22.0 26.3 38.7 70 VCC -1.0 0
Equalizer S/N Equalizer maximum input Equalizer Total Harmonic Distortion Equalizer offset voltage Equalizer frequency responce (TYPE I-NORM)
Vin max (EQ) T.H.D. (EQ)
55 10.5 --
Equalizer frequency responce (TYPE II-NORM)
Equalizer frequency responce (TYPE I-HIGH)
Equalizer frequency responce (TYPE II-HIGH)
REC MUTE attenuation Bias out Max level
Vofs (EQ) GVEQ-1N1 GVEQ-1N2 GVEQ-1N3 GVEQ-2N1 GVEQ-2N2 GVEQ-2N3 GVEQ-1H1 GVEQ-1H2 GVEQ-1H3 GVEQ-2H1 GVEQ-2H2 GVEQ-2H3 REC-MUTE Bias on
Electrical Characteristics (Ta=25C, VCC = 12V, Dolby Level = REC-OUT Level = 300mVrms = 0dB) (cont)
Bias out offset
Bias off
-500 18.5 19.4 29.1 21.4 23.3 32.0 17.7 19.8 31.0 20.5 24.3 35.7 60 VCC -1.4 -100
PB REC OUT (L) OUT (L)
R16 6.8k R19 R18 22k 10k R17 20k C26 0.01 C11 + 2.2 R12 330k 0.33 R15 5.1k C13 0.47 R14 5.1k
EQ OUT (L)
+ EQIN (L) +C10 29 28 100k MS DET BIAS (N)
R8 910 R9 2.4k R10 2k R11 3.9k R13 10k
Test Circuit
C16 2.2
C15 +0.1
C14 2.2
JP1 C12 + 0.47
42 EQ
41
40
39
+ 38 37 36 35 34 33 32 31 30
43 27 26 25 BIAS (C) 24 23 22 + LPF 21 20 DOLBY B-NR 15k 12k 18 17 16 15 8
0.47 JP2 R5 5.1k R4 6.8k
RIN (L)
R20 5.1k C17 0.47
44
BIN (L)
R21 C18 10k 0.47
45 15k 12k DOLBY B-NR VCC 45k
- +
C19 0.0047
+
MSOUT BIASOUT
+
46
BIAS SW
47
AIN (L)
R22 C20 10k 0.47
48
C21 1
+
+ LM ON/ REC/ 19 NR ON/
R26 22k SW9 C9 100 VCC1
49
+
50
SW8
51
SW7
AIN (R)
R23 C22 10k 0.47
+ +
RM /OFF BIAS ON/ B /70 /HIGH
52
C23 0.0047
+
53
C8 22 C7 22 SW6
+
BIN (R)
54
R24 C24 10k 0.47
+
R27 22k
SW5
55
VCC2 5V SW4
RIN (R)
56 EQ 1
C1 2.2 C3 2.2 R3 20k R2 10k
R25 C25 5.1k 0.47
+
SW3
2 +
C2 0.1
3 +
4
5
6 + C5
7
9 + C6
2.2
10
11
12
13
14 A EQIN (R) /70 PB /B
SW2
SW1
R1 33k
+
R7 10k C4 0.47 R6 5.1k
Rev.2, Jun. 1999, page 17 of 49
PB REC OUT (R) OUT (R) EQ OUT (R)
HA12209F
Unit
R: C:F
HA12209F
Parallel Data Format
Pin No. 10 11 12 14 16 17 19 20 21 Note: Pin Name PB A/B A 120/70 NORM/HIGH B 120/70 BIAS ON/OFF RM ON/OFF NR ON/OFF REC/PB LM ON/OFF 1. PB EQ LOGIC PB A/B A 120 120/70 Lo Lo Hi Hi B 120 120/70 Lo Hi Lo Hi Lo FLAT FLAT 70 70 Hi FLAT 70 FLAT 70 Lo Ain* *
1 1
Hi Bin* *
1 1 1
Mode "Pin Open" Lo Lo Lo
1
Normal speed REC EQ TYPE I* Bias TYPE I BIAS OFF REC MUTE ON NR OFF PB MODE LINE MUTE OFF
High speed REC EQ TYPE II* Bias TYPE II BIAS OFF REC MUTE OFF NR ON REC MODE LINE MUTE ON
Lo Lo Lo Lo Lo Lo
Rev.2, Jun. 1999, page 18 of 49
HA12209F
Characteristics Curve
Quiescent Current vs. Supply Voltage (1) 25 RECmode
Quiescent Current (mA)
20
15 No Signal NR-OFF, REC-MUTE ON NR-OFF, REC-MUTE OFF NR-ON, REC-MUTE ON NR-ON, REC-MUTE OFF Other SW is "Low" 10 8 10 12 Supply Voltage (V) 14 16
Quiescent Current vs. Supply Voltage (2) 25 PBmode
Quiescent Current (mA)
20
15 No Signal NR-OFF, REC-MUTE ON NR-OFF, REC-MUTE OFF NR-ON, REC-MUTE ON NR-ON, REC-MUTE OFF Other SW is "Low" 10 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 19 of 49
HA12209F
Input Amp. Gain vs. Frequency (1) 30 A
Input Amp. Gain (dB)
A 70
20
VCC=12V PBmode NR-OFF AINPBOUT 10 10 100 1k 10k Frequency (Hz) Input Amp. Gain vs. Frequency (2) 30 100k 1M
Input Amp. Gain (dB)
20
VCC=12V PBmode NR-OFF AINRECOUT 10 10 100 1k 10k Frequency (Hz) 100k 1M
Rev.2, Jun. 1999, page 20 of 49
HA12209F
Input Amp. Gain vs. Frequency (3) 30
Input Amp. Gain (dB)
PBOUT
20 RECOUT
VCC = 12V RECmode NR-OFF RIN PBOUT, RECOUT 10 10 100 1k 10k Frequency (Hz) 100k 1M
Rev.2, Jun. 1999, page 21 of 49
HA12209F
Encode Boost vs. Frequency 12 VCC = 12V Vin = -40dB
Encode Boost (dB)
8 -30dB
4
-20dB
-10dB 0dB 0 100 1k Frequency (Hz) Decode Cut vs. Frequency 0 Vin = 0dB -10dB -2 -20dB
Decode Cut (dB)
10k
20k
-4
-6 -30dB -8
-10 VCC=12V -12 100 1k Frequency (Hz) 10k -40dB 20k
Rev.2, Jun. 1999, page 22 of 49
HA12209F
Maximum Output Level vs. Supply Voltage (1) 25 NR-OFF NR-ON PBmode Ain PBOUT 0dB = 580mVrms (at PBOUT) T.H.D = 1% f = 1kHz 400Hz LPF + 30kHz HPF
Maximum Output Level Vomax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
Maximum Output Level vs. Supply Voltage (2) 25
Maximum Output Level Vomax (dB)
20
15
NR-OFF NR-ON PBmode Ain RECOUT 0dB = 300mVrms (at RECOUT) T.H.D = 1% f = 1kHz 400Hz LPF + 30kHz HPF 8 10 12 Supply Voltage (V) 14 16
10
Rev.2, Jun. 1999, page 23 of 49
HA12209F
Maximum Output Level vs. Supply Voltage (3) 25
Maximum Output Level Vomax (dB)
20
15
NR-OFF NR-ON RECmode Rin RECOUT 0dB = 300mVrms (at RECOUT) T.H.D = 1% f = 1kHz 400Hz LPF + 30kHz HPF 8 10 12 Supply Voltage (V) 14 16
10
Maximum Output Level vs. Supply Voltage (4) 25 NR-OFF NR-ON RECmode Rin PBOUT 0dB = 580mVrms (at PBOUT) T.H.D = 1% f = 1kHz 400Hz LPF + 30kHz HPF
Maximum Output Level Vomax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 24 of 49
HA12209F
Signal to Noise Ratio vs. Supply Voltage (1) 85
Signal to Noise Ratio S/N (dB)
80
75 NR-OFF NR-ON PBmode Ain PBOUT CCIR/ARM 0dB = 580mVrms (PBOUT) 70 8 10 12 Supply Voltage (V) 14 16
Signal to Noise Ratio vs. Supply Voltage (2) 85
Signal to Noise Ratio S/N (dB)
80 NR-OFF NR-ON RECmode Rin RECOUT CCIR/ARM 0dB = 300mVrms (RECOUT) 75
70 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 25 of 49
HA12209F
Total Harmonic Distortion vs. Supply Voltage (1) 1.0 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 8kHz LPF) PBmode NR-OFF Ain PBOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.01 8 10 12 Supply Voltage (V) 14 16
Total Harmonic Distortion vs. Supply Voltage (2) 1.0 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 8kHz LPF) PBmode NR-ON Ain PBOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.01 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 26 of 49
HA12209F
Total Harmonic Distortion vs. Supply Voltage (3) 1.0 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 8kHz LPF) RECmode NR-OFF Rin RECOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.01 8 10 12 Supply Voltage (V) 14 16
Total Harmonic Distortion vs. Supply Voltage (4) 1.0 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 8kHz LPF) RECmode NR-ON Rin RECOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.01 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 27 of 49
HA12209F
Total Harmonic Distortion vs. Output Level (1) 10 100Hz 1kHz 10kHz VCC = 12V, PBmode NR-OFF, AIN PBOUT 0dB = 580mVrms (at PBOUT) 1
Total Harmonic Distortion T.H.D (%)
0.1
0.01 -25
-20
-15
-10 -5 0 5 Output Level Vout (dB)
10
15
20
Total Harmonic Distortion vs. Output Level (2) 10 100Hz 1kHz 10kHz VCC = 12V, PBmode NR-ON, AIN PBOUT 0dB = 580mVrms (at PBOUT) 1
Total Harmonic Distortion T.H.D (%)
0.1
0.01 -25
-20
-15
-10 -5 0 5 Output Level Vout (dB)
10
15
20
Rev.2, Jun. 1999, page 28 of 49
HA12209F
Total Harmonic Distortion vs. Output Level (3) 10 100Hz 1kHz 10kHz VCC = 12V, RECmode NR-OFF, RIN RECOUT 0dB = 300mVrms (at RECOUT) 1
Total Harmonic Distortion T.H.D (%)
0.1
0.01 -15
-10
-5
0 5 10 Output Level Vout (dB)
15
20
25
Total Harmonic Distortion vs. Output Level (4) 10 100Hz 1kHz 10kHz VCC = 12V, RECmode NR-ON, RIN RECOUT 0dB = 300mVrms (at RECOUT) 1
Total Harmonic Distortion T.H.D (%)
0.1
0.01 -20
-15
-10
-5
0 5 10 Output Level Vout (dB)
15
20
25
Rev.2, Jun. 1999, page 29 of 49
HA12209F
Total Harmonic Distortion vs. Frequency (1) 0.5 +10dB 0dB -10dB VCC = 12V, PBmode NR-OFF, AIN PBOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.05
0.01 100
1k Frequency (Hz) Total Harmonic Distortion vs. Frequency (2)
10k
20k
0.5 +10dB 0dB -10dB VCC =12V, PBmode NR-ON, AIN PBOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.05
0.01 100
1k Frequency (Hz)
10k
20k
Rev.2, Jun. 1999, page 30 of 49
HA12209F
Total Harmonic Distortion vs. Frequency (3) 0.5 +10dB 0dB -10dB VCC = 12V, RECmode NR-OFF, RIN RECOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.05
0.01 100
1k Frequency (Hz) Total Harmonic Distortion vs. Frequency (4)
10k
20k
0.5 +10dB 0dB -10dB VCC =12V, RECmode NR-ON, RIN RECOUT Vin = 0dB
Total Harmonic Distortion T.H.D (%)
0.1
0.05
0.01 100
1k Frequency (Hz)
10k
20k
Rev.2, Jun. 1999, page 31 of 49
HA12209F
Crosstalk vs. Frequency (1) -40 AIN BIN VCC = 12V PBmode (AIN, PBOUT) Vin = +10dB NR-OFF
Crosstalk (dB)
-60
-80
NR-ON -100
-120
-140 10
100
1k Frequency (Hz) Crosstalk vs. Frequency (2)
10k
100k
-40 BIN AIN VCC = 12V PBmode (BIN, PBOUT) Vin = +10dB NR-OFF
Crosstalk (dB)
-60
-80
NR-ON -100
-120
-140 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 32 of 49
HA12209F
Crosstalk vs. Frequency (3) -40 PB REC VCC = 12V PBmode (AIN, RECOUT) Vin = +10dB
-60
NR-ON
Crosstalk (dB)
-80 NR-OFF -100
-120
-140 10
100
1k Frequency (Hz) Crosstalk vs. Frequency (4)
10k
100k
-40 REC PB VCC = 12V RECmode (RIN, PBOUT) Vin = +12dB
-60
Crosstalk (dB)
-80
NR-OFF
-100 NR-ON
-120
-140 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 33 of 49
HA12209F
Channel Separation vs. Frequency (1) -20 VCC = 12V PBmode (AIN, PBOUT), 120 Vin = +10dB -40
Channel Separation (dB)
-60 NR-OFF -80 NR-ON -100
-120 10
100
1k Frequency (Hz)
10k
100k
Channel Separation vs. Frequency (2) -20 VCC = 12V PBmode (BIN, PBOUT), 120 Vin = +10dB -40
Channel Separation (dB)
-60
NR-OFF -80
NR-ON -100
-120 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 34 of 49
HA12209F
Channel Separation vs. Frequency (3) -40 VCC = 12V RECmode (RIN, RECOUT) Vin = +12dB -60
Channel Separation (dB)
-80
NR-ON
-100
-120
NR-OFF
-140 10
100
1k Frequency (Hz)
10k
100k
LINE-MUTE Attenuation vs. Frequency (1) -40 VCC = 12V PBmode (AIN, PBOUT) NR-OFF Vin = +12dB
-60
LINE-MUTE Attenuation (dB)
-80
-100
-120
-140 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 35 of 49
HA12209F
LINE-MUTE Attenuation vs. Frequency (2) -40 VCC = 12V PBmode (BIN, PBOUT) NR-OFF Vin = +12dB
-60
LINE-MUTE Attenuation (dB)
-80
-100
-120
-140 10
100
1k Frequency (Hz)
10k
100k
LINE-MUTE Attenuation vs. Frequency (3) -40 VCC = 12V RECmode (RIN, PBOUT) NR-OFF Vin = +12dB
-60
LINE-MUTE Attenuation (dB)
-80
-100
-120
-140 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 36 of 49
HA12209F
Ripple Relection Ratio vs. Frequency (1) 0 VCC = 12V PBmode
Ripple Relection Ratio R.R.R. (dB)
-20
PBOUT NR-ON PBOUT NR-OFF
-40 RECOUT NR-ON -60 RECOUT NR-OFF
-80
-100 10
100
1k Frequency (Hz)
10k
100k
Ripple Relection Ratio vs. Frequency (2) 0 VCC = 12V RECmode
Ripple Relection Ratio R.R.R. (dB)
-20
RECOUT NR-ON
PBOUT NR-ON/OFF
-40
RECOUT NR-OFF -60
-80
-100 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 37 of 49
HA12209F
Ripple Relection Ratio vs. Frequency (3) 0 VCC = 12V EQOUT N : Normal speed
Ripple Relection Ratio R.R.R. (dB)
N-TYPE II
-20 N-TYPE I -40
-60
-80
-100 10
100
1k Frequency (Hz) REC-EQ Gain vs. Frequency
10k
100k
50 VCC = 12V N : Normal speed H : High speed 40 N-TYPE II
REC-EQ Gain (dB)
N-TYPE I 30
20 H-TYPE I H-TYPE II 10
0 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 38 of 49
HA12209F
EQ Maximum Input Level vs. Supply Voltage (1) 25 f = 1kHz, EQin EQOUT Vin = -26dBs, T.H.D 1% Norm speed, TYPE I
EQ Maximum Input Level Vinmax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
EQ Maximum Input Level vs. Supply Voltage (2) 25 f = 1kHz, EQin EQOUT Vin = -26dBs, T.H.D 1% Norm speed, TYPE II
EQ Maximum Input Level Vinmax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 39 of 49
HA12209F
EQ Maximum Input Level vs. Supply Voltage (3) 25 f = 1kHz, EQin EQOUT Vin = -26dBs, T.H.D 1% High speed, TYPE I
EQ Maximum Input Level Vinmax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
EQ Maximum Input Level vs. Supply Voltage (4) 25 f = 1kHz, EQin EQOUT Vin = -26dBs, T.H.D 1% High speed, TYPE II
EQ Maximum Input Level Vinmax (dB)
20
15
10 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 40 of 49
HA12209F
EQ Signal to Noise Ratio vs. Supply Voltage 65
EQ Signal to Noise Ratio EQ S/N (dB)
60
55
N-TYPE I N-TYPE II H-TYPE I H-TYPE II A-WTG filter N : Normal speed H : High speed 8 10 12 Supply Voltage (V) 14 16
50
EQ Total Harmonic Distortion vs. Supply Voltage (1) 10
EQ Total Harmonic Distortion EQ T.H.D (%)
315Hz (30kHz LPF) 1kHz (30kHz LPF + 400Hz HPF) 5kHz (30kHz LPF + 400Hz HPF) 10kHz (30kHz LPF + 400Hz HPF) EQin EQOUT, Vin = -26dBs Normal speed, TYPE I
1.0
0.1 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 41 of 49
HA12209F
EQ Total Harmonic Distortion vs. Supply Voltage (2) 10
EQ Total Harmonic Distortion EQ T.H.D (%)
315Hz (30kHz LPF) 1kHz (30kHz LPF + 400Hz HPF) 5kHz (30kHz LPF + 400Hz HPF) 10kHz (30kHz LPF + 400Hz HPF) EQin EQOUT, Vin = -26dBs Normal speed, TYPE II
1.0
0.1 8 10 12 Supply Voltage (V) 14 16
EQ Total Harmonic Distortion vs. Supply Voltage (3) 10
EQ Total Harmonic Distortion EQ T.H.D (%)
315Hz (30kHz LPF) 2kHz (30kHz LPF + 400Hz HPF) 10kHz (30kHz LPF + 400Hz HPF) EQin EQOUT, Vin = -26dBs High speed, TYPE I
1.0
0.1 8 10 12 Supply Voltage (V) 14 16
Rev.2, Jun. 1999, page 42 of 49
HA12209F
EQ Total Harmonic Distortion vs. Supply Voltage (4) 10
EQ Total Harmonic Distortion EQ T.H.D (%)
315Hz (30kHz LPF) 2kHz (30kHz LPF + 400Hz HPF) 10kHz (30kHz LPF + 400Hz HPF) EQin EQOUT, Vin = -26dBs High speed, TYPE II
1.0
0.1 8 10 12 Supply Voltage (V) 14 16
EQ Total Harmonic Distortion vs. Input Level (1) 100
EQ Total Harmonic Distortion EQ T.H.D (%)
10
315Hz 1kHz 5kHz 10kHz VCC = 12V, EQin EQOUT, Vin = -26dBs = 0dB Normal speed, TYPE I
1.0
0.1 -30
-20
-10 10 0 Input Level (dB)
20
30
Rev.2, Jun. 1999, page 43 of 49
HA12209F
EQ Total Harmonic Distortion vs. Input Level (2) 100
EQ Total Harmonic Distortion EQ T.H.D (%)
10
315Hz 1kHz 5kHz 10kHz VCC = 12V, EQin EQOUT, Vin = -26dBs = 0dB Normal speed, TYPE II
1.0
0.1 -30
-20
-10 10 0 Input Level (dB)
20
30
EQ Total Harmonic Distortion vs. Input Level (3) 100
EQ Total Harmonic Distortion EQ T.H.D (%)
10
315Hz 2kHz 10kHz 20kHz VCC = 12V, EQin EQOUT, Vin = -26dBs = 0dB High speed, TYPE I
1.0
0.1 -30
-20
-10 10 0 Input Level (dB)
20
30
Rev.2, Jun. 1999, page 44 of 49
HA12209F
EQ Total Harmonic Distortion vs. Input Level (4) 100
EQ Total Harmonic Distortion EQ T.H.D (%)
10
315Hz 2kHz 10kHz 20kHz VCC = 12V, EQin EQOUT, Vin = -26dBs = 0dB High speed, TYPE II
1.0
0.1 -30
-20
-10 10 0 Input Level (dB)
20
30
REC-MUTE Attenuation vs. Frequency -40 VCC = 12V
-60
REC-MUTE Attenuation (dB)
-80
-100
-120
-140 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 45 of 49
HA12209F
MS AMP. Gain vs. Frequency 40 VCC =12V
30 MAOUT
MS AMP. Gain (dB)
20 MSIN
10
0
-10 10
100
1k Frequency (Hz) MS Sensitivity vs. Frequency
10k
100k
10 VCC =12V Hi Lo Lo Hi 5
MS Sensitivity (dB)
0
-5
-10
-15 10
100
1k Frequency (Hz)
10k
100k
Rev.2, Jun. 1999, page 46 of 49
HA12209F
No-Signal Sensing Time vs. Resistance 10000 PBOUT MSOUT
No-Signal Sensing Time (ms)
1000
VCC 22 R12 29 MSDET
C10
100
10 +10dB 0dB -10dB VS = 12V, f = 5kHz 1 10k 100k Resistance R12 () 1M
Signal Sensing Time vs. Capacitance 1000 PBOUT MSOUT 100 VCC 22 R12 29 MSDET
Signal Sensing Time (ms)
C10
10
1.0 +10dB 0dB -10dB VS = 12V, f = 5kHz 0.1 0.01 0.1 Capacitor C10 (F) 1.0
Rev.2, Jun. 1999, page 47 of 49
HA12209F
Package Dimensions
12.8 0.3
10.0 42 29 28
Unit: mm
43
12.8 0.3
56 1
*0.32 0.08 0.30 0.06
0.13 M
15 14
2.54 Max *0.17 0.05 0.15 0.04
0.775
0.35
2.20
0.65
0.775
1.40
0.1 +0.1 -0.09
0 -8
0.10
0.60 0.15
Hitachi Code JEDEC EIAJ Weight (reference value) FP-56 -- -- 0.5 g
*Dimension including the plating thickness Base material dimension
Rev.2, Jun. 1999, page 48 of 49
HA12209F
Disclaimer
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party's rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi's sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor products.
Sales Offices
Hitachi, Ltd.
Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica : http://semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia : http://sicapac.hitachi-asia.com Japan : http://www.hitachi.co.jp/Sicd/indx.htm For further information write to:
Hitachi Europe GmbH Electronic Components Group Dornacher Strae 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 585160 Hitachi Asia Ltd. Hitachi Tower 16 Collyer Quay #20-00, Singapore 049318 Tel : <65>-538-6533/538-8577 Fax : <65>-538-6933/538-3877 URL : http://www.hitachi.com.sg Hitachi Asia Ltd. (Taipei Branch Office) 4/F, No. 167, Tun Hwa North Road, Hung-Kuo Building, Taipei (105), Taiwan Tel : <886>-(2)-2718-3666 Fax : <886>-(2)-2718-8180 Telex : 23222 HAS-TP URL : http://www.hitachi.com.tw Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road Tsim Sha Tsui, Kowloon, Hong Kong Tel : <852>-(2)-735-9218 Fax : <852>-(2)-730-0281 URL : http://www.hitachi.com.hk
Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223
Copyright Hitachi, Ltd., 2000. All rights reserved. Printed in Japan. Colophon 2.0
Rev.2, Jun. 1999, page 49 of 49

▲Up To Search▲

Price & Availability of HA12209

	To Download HA12209 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .