View ISL652607_706319.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISL6526, ISL6526A
Data Sheet March 20, 2007 FN9055.8
Single Synchronous Buck Pulse-Width Modulation (PWM) Controller
The ISL6526, ISL6526A make simple work out of implementing a complete control and protection scheme for a DC/DC stepdown converter. Designed to drive N-Channel MOSFETs in a synchronous buck topology, the ISL6526, ISL6526A integrate the control, output adjustment, monitoring and protection functions into a single package. The ISL6526, ISL6526A provide simple, single feedback loop, voltage-mode control with fast transient response. The output voltage can be precisely regulated to as low as 0.8V, with a maximum tolerance of 1.5% over temperature and line voltage variations. A fixed frequency oscillator reduces design complexity, while balancing typical application cost and efficiency. The error amplifier features a 15MHz gain-bandwidth product and 6V/s slew rate which enables high converter bandwidth for fast transient performance. The resulting PWM duty cycles range from 0% to 100%. Protection from overcurrent conditions is provided by monitoring the rDS(ON) of the upper MOSFET to inhibit PWM operation appropriately. This approach simplifies the implementation and improves efficiency by eliminating the need for a current sense resistor.
Features
* Operates from 3.3V to 5V Input * 0.8V to VIN Output Range - 0.8V Internal Reference - 1.5% Over Load, Line Voltage and Temperature * Drives N-Channel MOSFETs * Simple Single-Loop Control Design - Voltage-Mode PWM Control * Fast Transient Response - High-Bandwidth Error Amplifier - Full 0% to 100% Duty Cycle * Lossless, Programmable Overcurrent Protection - Uses Upper MOSFET's rDS(on) * Converter can Source and Sink Current * Small Converter Size - Internal Fixed Frequency Oscillator - ISL6526: 300kHz - ISL6526A: 600kHz * Internal Soft-Start * 14 Lead SOIC or 16 Lead 5x5 QFN * QFN Package: - Compliant to JEDEC PUB95 MO-220 QFN - Quad Flat No Leads - Package Outline - Near Chip Scale Package footprint, which improves PCB efficiency and has a thinner profile * Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
* Power Supplies for Microprocessors - PCs - Embedded Controllers * Subsystem Power Supplies - PCI/AGP/GTL+ Buses - ACPI Power Control - DDR SDRAM Bus Termination Supply * Cable Modems, Set Top Boxes, and DSL Modems * DSP and Core Communications Processor Supplies * Memory Supplies * Personal Computer Peripherals * Industrial Power Supplies * 3.3V-Input DC/DC Regulators * Low-Voltage Distributed Power Supplies
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2001-2005, 2007. All Rights Reserved. All other trademarks mentioned are the property of their respective owners.
ISL6526, ISL6526A Ordering Information
PART NUMBER (Note) ISL6526CB* ISL6526CBZ* ISL6526ACB* ISL6526ACBZ* ISL6526CR* ISL6526CRZ* ISL6526ACR* ISL6526ACRZ* ISL6526IB* ISL6526IBZ* ISL6526AIB* ISL6526AIBZ* ISL6526IR* ISL6526IRZ* ISL6526AIR* ISL6526AIRZ* ISL6526EVAL1 ISL6526EVAL2 ISL6526AEVAL1 ISL6526AEVAL2 *Add "-T" suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. PART MARKING ISL6526CB 6526CBZ ISL6526ACB 6526ACBZ ISL 6526CR ISL6526 CRZ ISL 6526ACR ISL6526 ACRZ ISL6526IB 6526IBZ ISL6526AIB 6526AIBZ ISL 6526IR ISL 6526IRZ ISL 6526AIR ISL65 26AIRZ ISL6526 SOIC Evaluation Board ISL6526 QFN Evaluation Board ISL6526A SOIC Evaluation Board ISL6526A QFN Evaluation Board TEMP RANGE (C) 0 to +70 0 to +70 0 to +70 0 to +70 0 to +70 0 to +70 0 to +70 0 to +70 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 PACKAGE 14 Ld SOIC 14 Ld SOIC (Pb-free) 14 Ld SOIC 14 Ld SOIC (Pb-free) 16 Ld 5x5 QFN 16 Ld 5x5 QFN (Pb-free) 16 Ld 5x5 QFN 16 Ld 5x5 QFN (Pb-free) 14 Ld SOIC 14 Ld SOIC (Pb-free) 14 Ld SOIC 14 Ld SOIC (Pb-free) 16 Ld 5x5 QFN 16 Ld 5x5 QFN (Pb-free) 16 Ld 5x5 QFN 16 Ld 5x5 QFN (Pb-free) PKG DWG. # M14.15 M14.15 M14.15 M14.15 L16.5x5B L16.5x5B L16.5x5B L16.5x5B M14.15 M14.15 M14.15 M14.15 L16.5x5B L16.5x5B L16.5x5B L16.5x5B
Pinouts
ISL6526, ISL6526A (14 LD SOIC) TOP VIEW
GND 1 LGATE 2 CPVOUT 3 CT1 4 CT2 5 OCSET 6 FB 7 14 UGATE 13 BOOT 12 PHASE 11 VCC 10 CPGND 9 ENABLE 8 COMP OCSET 4 5 NC 6 FB 7 COMP 8 ENABLE 9 NC CPVOUT CT1 CT2 1 2 3 12 PHASE 11 VCC 10 CPGND
ISL6526, ISL6526A (16 LD QFN) TOP VIEW
UGATE 14 LGATE BOOT 13 GND 15
16
2
FN9055.8 March 20, 2007
ISL6526, ISL6526A Typical Application - 3.3V Input
3.3V VIN CIN CBULK OCSET ROCSET CPUMP CT2 BOOT CBOOT UGATE PHASE ENABLE LGATE DISABLE COMP FB Q2 Q1 LOUT CPVOUT ISL6526, ISL6526A DBOOT CDCPL CHF
VCC CT1
CPGND GND
VOUT
COUT
CI RFB RF CF ROFFSET
3
FN9055.8 March 20, 2007
ISL6526, ISL6526A Typical Application - 5V Input
+5V VIN
VCC CT1 OCSET ROCSET CPVOUT ISL6526, ISL6526A N/C CT2 BOOT CBOOT UGATE PHASE ENABLE LGATE DISABLE COMP FB Q2 Q1 DBOOT CIN
CBULK
CHF
CPGND GND
LOUT
VOUT
COUT
CI RFB RF CF ROFFSET
Block Diagram
VCC CPVOUT
CT1 CT2 CPGND OCSET 20A
CHARGE PUMP
POWER-ON RESET (POR)
ENABLE
BOOT OC COMPARATOR + SOFT-START UGATE
PHASE ERROR AMP + PWM COMPARATOR + INHIBIT
+ 0.8V -
GATE CONTROL LOGIC PWM
LGATE FB OSCILLATOR COMP FIXED 300kHz or 600kHz GND
4
FN9055.8 March 20, 2007
ISL6526, ISL6526A
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Absolute Boot Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . . . +15.0V Upper Driver Supply Voltage, VBOOT - VPHASE . . . . . . . . . . . +7.0V Input, Output or I/O Voltage . . . . . . . . . . . GND -0.3V to VCC +0.3V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2
Thermal Information
Thermal Resistance JA (C/W) JC (C/W) SOIC Package (Note 1) . . . . . . . . . . . . 67 N/A QFN Package (Note 2). . . . . . . . . . . . . 35 5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150C Maximum Storage Temperature Range . . . . . . . . . .-65C to +150C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300C (SOIC - Lead Tips Only) For Recommended soldering conditions see Tech Brief TB389.
Operating Conditions
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V 10% Ambient Temperature Range . . . . . . . . . . . . . . . . . . .-40C to +85C Junction Temperature Range. . . . . . . . . . . . . . . . . .-40C to +125C
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. JC, the "case temp" is measured at the center of the exposed metal pad on the package underside. See Tech Brief TB379.
Electrical Specifications
PARAMETER VCC SUPPLY CURRENT Nominal Supply POWER-ON RESET Rising CPVOUT POR Threshold
Recommended Operating Conditions, unless otherwise noted VCC = 3.3V 5% and TA = +25C SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
IBIAS
6.1
6.9
7.7
mA
POR
Commercial Industrial
4.25 4.10 0.3
4.30 4.30 0.6
4.42 4.50 0.9
V V V
CPVOUT POR Threshold Hysteresis OSCILLATOR Frequency fOSC IC = ISL6526C, Commercial IC = ISL6526I, Industrial IC = ISL6526AC, Commercial IC = ISL6526AI, Industrial Ramp Amplitude REFERENCE Reference Voltage Tolerance Nominal Reference Voltage CHARGE PUMP Nominal Charge Pump Output Charge Pump Output Regulation ERROR AMPLIFIER DC Gain Gain-Bandwidth Product Slew Rate SOFT-START Soft-Start Slew Rate Commercial Industrial GBWP SR Guaranteed by Design VCPVOUT VVCC = 3.3V, No Load VREF VOSC
275 250 530 510 -
300 300 600 600 1.5
325 340 645 650 -
kHz kHz kHz kHz VP-P
-
0.800
1.5 -
% V
-
5.1 2
-
V %
-
88 15 6
-
dB MHz V/s
6.2 6.2
-
7.3 7.6
ms ms
5
FN9055.8 March 20, 2007
ISL6526, ISL6526A
Electrical Specifications
PARAMETER GATE DRIVERS Upper Gate Source Current Upper Gate Sink Current Lower Gate Source Current Lower Gate Sink Current PROTECTION/DISABLE OCSET Current Source IOCSET Commercial Industrial Disable Threshold VDISABLE 18 16 20 20 22 22 0.8 A A V IUGATE-SRC VBOOT - VPHASE = 5V, VUGATE = 4V IUGATE-SNK ILGATE-SRC VVCC = 3.3V, VLGATE = 4V ILGATE-SNK -1 1 -1 2 A A A A Recommended Operating Conditions, unless otherwise noted VCC = 3.3V 5% and TA = +25C (Continued) SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Functional Pin Description
14 LEAD (SOIC) TOP VIEW
GND 1 LGATE 2 CPVOUT 3 CT1 4 CT2 5 OCSET 6 FB 7 14 UGATE 13 BOOT 12 PHASE 11 VCC 10 CPGND 9 ENABLE 8 COMP
GND
This pin represents the signal and power ground for the IC. Tie this pin to the ground island/plane through the lowest impedance connection available.
PHASE
Connect this pin to the upper MOSFET's source. This pin is used to monitor the voltage drop across the upper MOSFET for overcurrent protection.
UGATE
Connect this pin to the upper MOSFET's gate. This pin provides the PWM-controlled gate drive for the upper MOSFET. This pin is also monitored by the adaptive shootthrough protection circuitry to determine when the upper MOSFET has turned off.
16 LEAD 5X5 (QFN) TOP VIEW
UGATE LGATE BOOT GND
BOOT
This pin provides ground referenced bias voltage to the upper MOSFET driver. A bootstrap circuit is used to create a voltage suitable to drive a logic-level N-Channel MOSFET.
16 CPVOUT CT1 CT2 OCSET 1 2 3 4 5 NC
15
14
13 12 PHASE 11 VCC 10 CPGND 9 NC
LGATE
Connect this pin to the lower MOSFET's gate. This pin provides the PWM-controlled gate drive for the lower MOSFET. This pin is also monitored by the adaptive shootthrough protection circuitry to determine when the lower MOSFET has turned off.
6 FB
7 COMP
8 ENABLE
OCSET
Connect a resistor (ROCSET) from this pin to the drain of the upper MOSFET (VIN). ROCSET, an internal 20A current source (IOCSET), and the upper MOSFET on-resistance (rDS(ON)) set the converter overcurrent (OC) trip point according to the following equation:
I OCSET xR OCSET I PEAK = ------------------------------------------------r DS ( ON )
VCC
This pin provides the bias supply for the ISL6526, ISL6526A. Connect a well-decoupled 3.3V supply to this pin.
COMP and FB
COMP and FB are the available external pins of the error amplifier. The FB pin is the inverting input of the internal error amplifier and the COMP pin is the error amplifier output. These pins are used to compensate the voltagecontrol feedback loop of the converter.
(EQ. 1)
An overcurrent trip cycles the soft-start function.
6
FN9055.8 March 20, 2007
ISL6526, ISL6526A
ENABLE
This pin is the open-collector enable pin. Pulling this pin to a level below 0.8V will disable the controller. Disabling the ISL6526, ISL6526A cause the oscillator to stop, the LGATE and UGATE outputs to be held low, and the soft-start circuitry to re-arm. width on the UGATE pin increases to reach the steady-state duty cycle at time t3.
(1V/DIV) CPVOUT (5V)
CT1 and CT2
These pins are the connections for the external charge pump capacitor. A minimum of a 0.1F ceramic capacitor is recommended for proper operation of the IC.
VCC (3.3V)
VOUT (2.50V)
CPVOUT
This pin represents the output of the charge pump. The voltage at this pin is the bias voltage for the IC. Connect a decoupling capacitor from this pin to ground. The value of the decoupling capacitor should be at least 10x the value of the charge pump capacitor. This pin may be tied to the bootstrap circuit as the source for creating the BOOT voltage.
0V T0 T1 T2 T3 TIME
FIGURE 1. SOFT-START INTERVAL
Shoot-Through Protection
A shoot-through condition occurs when both the upper MOSFET and lower MOSFET are turned on simultaneously, effectively shorting the input voltage to ground. To protect the regulator from a shoot-through condition, the ISL6526, ISL6526A incorporate specialized circuitry which insures that the complementary MOSFETs are not ON simultaneously. The adaptive shoot-through protection utilized by the ISL6526, ISL6526A look at the lower gate drive pin, LGATE, and the upper gate drive pin, UGATE, to determine whether a MOSFET is ON or OFF. If the voltage from UGATE or from LGATE to GND is less than 0.8V, then the respective MOSFET is defined as being OFF and the complementary MOSFET is turned ON. This method of shoot-through protection allows the regulator to sink or source current. Since the voltage of the lower MOSFET gate and the upper MOSFET gate are being measured to determine the state of the MOSFET, the designer is encouraged to consider the repercussions of introducing external components between the gate drivers and their respective MOSFET gates before actually implementing such measures. Doing so may interfere with the shoot-through protection.
CPGND
This pin represents the signal and power ground for the charge pump. Tie this pin to the ground island/plane through the lowest impedance connection available.
Functional Description
Initialization
The ISL6526, ISL6526A automatically initialize upon receipt of power. Special sequencing of the input supplies is not necessary. The Power-On Reset (POR) function continually monitors the output voltage of the charge pump. During POR, the charge pump operates on a free running oscillator. Once the POR level is reached, the charge pump oscillator is synched to the PWM oscillator. The POR function also initiates the soft-start operation after the charge pump output voltage exceeds its POR threshold.
Soft-Start
The POR function initiates the digital soft-start sequence. The PWM error amplifier reference is clamped to a level proportional to the soft-start voltage. As the soft-start voltage slews up, the PWM comparator generates PHASE pulses of increasing width that charge the output capacitor(s). This method provides a rapid and controlled output voltage rise. The soft-start sequence typically takes about 6.5ms. Figure 1 shows the soft-start sequence for a typical application. At t0, the +3.3V VCC voltage starts to ramp. At time t1, the Charge Pump begins operation and the +5V CPVOUT IC bias voltage starts to ramp up. Once the voltage on CPVOUT crosses the POR threshold at time t2, the output begins the soft-start sequence. The triangle waveform from the PWM oscillator is compared to the rising error amplifier output voltage. As the error amplifier voltage increases, the pulse-
Output Voltage Selection
The output voltage can be programmed to any level between VIN and the internal reference, 0.8V. An external resistor divider is used to scale the output voltage relative to the reference voltage and feed it back to the inverting input of the error amplifier, see Figure 2. However, since the value of R1 affects the values of the rest of the compensation components, it is advisable to keep its value less than 5k. R4 can be calculated based on the following equation:
R1 x 0.8V R4 = ------------------------------------V OUT1 - 0.8V
(EQ. 2)
7
FN9055.8 March 20, 2007
ISL6526, ISL6526A
If the output voltage desired is 0.8V, simply route the output back to the FB pin through R1, but do not populate R4.
+3.3V VOUT (2.5V) VCC CPVOUT D1 BOOT C4 ISL6526, ISL6526A UGATE PHASE LGATE Q2 + COUT Q1 VIN
delay interval of three soft-start cycles. The resulting hiccup mode style of protection would continue to repeat indefinitely.
LOUT
VOUT
0V
INTERNAL SOFT-START FUNCTION
FB COMP C1 R1 C3 DELAY INTERVAL R3
C2
R2 R4 T0 TIME T1 T2
FIGURE 3. OVERCURRENT PROTECTION RESPONSE FIGURE 2. OUTPUT VOLTAGE SELECTION
Overcurrent Protection
The overcurrent function protects the converter from a shorted output by using the upper MOSFET on-resistance, rDS(ON), to monitor the current. This method enhances the converter's efficiency and reduces cost by eliminating a current sensing resistor. The overcurrent function cycles the soft-start function in a hiccup mode to provide fault protection. A resistor (ROCSET) programs the overcurrent trip level (see Typical Application diagrams on pages 3 and 4). An internal 20A (typical) current sink develops a voltage across ROCSET that is referenced to VIN. When the voltage across the upper MOSFET (also referenced to VIN) exceeds the voltage across ROCSET, the overcurrent function initiates a soft-start sequence. Figure 3 illustrates the protection feature responding to an overcurrent event. At time t0, an overcurrent condition is sensed across the upper MOSFET. As a result, the regulator is quickly shutdown and the internal soft-start function begins producing soft-start ramps. The delay interval seen by the output is equivalent to three soft-start cycles. The fourth internal soft-start cycle initiates a normal soft-start ramp of the output, at time T1. The output is brought back into regulation by time T2, as long as the overcurrent event has cleared. Had the cause of the overcurrent still been present after the delay interval, the overcurrent condition would be sensed and the regulator would be shut down again for another
The overcurrent function will trip at a peak inductor current (IPEAK) determined by:
I OCSET x R OCSET I PEAK = ---------------------------------------------------r DS ( ON )
(EQ. 3)
where IOCSET is the internal OCSET current source (20A typical). The OC trip point varies mainly due to the MOSFET rDS(ON) variations. To avoid overcurrent tripping in the normal operating load range, find the ROCSET resistor from the equation above with: 1. The maximum rDS(ON) at the highest junction temperature. 2. The minimum IOCSET from the specification table.
3. Determine IPEAK for I PEAK > I OUT ( MAX ) + --------- , 2 ( I )
where I is the output inductor ripple current.
For an equation for the ripple current see the section under component guidelines titled `Output Inductor Selection'. A small ceramic capacitor should be placed in parallel with ROCSET to smooth the voltage across ROCSET in the presence of switching noise on the input voltage.
Current Sinking
The ISL6526, ISL6526A incorporate a MOSFET shootthrough protection method which allows a converter to sink current as well as source current. Care should be exercised when designing a converter with the ISL6526, ISL6526A when it is known that the converter may sink current.
8
FN9055.8 March 20, 2007
ISL6526, ISL6526A
When the converter is sinking current, it is behaving as a boost converter that is regulating its input voltage. This means that the converter is boosting current into the input rail of the regulator. If there is nowhere for this current to go, such as to other distributed loads on the rail or through a voltage limiting protection device, the capacitance on this rail will absorb the current. This situation will allow the voltage level of the input rail to increase. If the voltage level of the rail is boosted to a level that exceeds the maximum voltage rating of any components attached to the input rail, then those components may experience an irreversible failure or experience stress that may shorten their lifespan. Ensuring that there is a path for the current to flow other than the capacitance on the rail will prevent this failure mode. circuit layers for small signal wiring. The wiring traces from the GATE pins to the MOSFET gates should be kept short and wide enough to easily handle the 1A of drive current.
+3.3V VIN ISL6526, ISL6526A VCC CVCC
CPVOUT CBP GND BOOT CBOOT Q1 UGATE PHASE PHASE Q2 LGATE COUT LOAD
FN9055.8 March 20, 2007
D1
CIN
Application Guidelines
Layout Considerations
Layout is very important in high frequency switching converter design. With power devices switching efficiently at 300kHz or 600kHz, the resulting current transitions from one device to another causing voltage spikes across the interconnecting impedances and parasitic circuit elements. These voltage spikes can degrade efficiency, radiate noise into the circuit, and lead to device overvoltage stress. Careful component layout and printed circuit board design minimizes the voltage spikes in the converters. As an example, consider the turn-off transition of the PWM MOSFET. Prior to turn-off, the MOSFET is carrying the full load current. During turn-off, current stops flowing in the MOSFET and is picked up by the lower MOSFET. Any parasitic inductance in the switched current path generates a large voltage spike during the switching interval. Careful component selection, tight layout of the critical components, and short, wide traces minimizes the magnitude of voltage spikes. There are two sets of critical components in a DC/DC converter using the ISL6526, ISL6526A. The switching components are the most critical because they switch large amounts of energy, and therefore tend to generate large amounts of noise. Next are the small signal components which connect to sensitive nodes or supply critical bypass current and signal coupling. A multi-layer printed circuit board is recommended. Figure 4 shows the connections of the critical components in the converter. Note that capacitors CIN and COUT could each represent numerous physical capacitors. Dedicate one solid layer, usually a middle layer of the PC board, for a ground plane and make all critical component ground connections with vias to this layer. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Keep the metal runs from the PHASE terminals to the output inductor short. The power plane should support the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers for the phase nodes. Use the remaining printed 9
LOUT
VOUT
COMP C2 R2 FB R4 KEY ISLAND ON POWER PLANE LAYER ISLAND ON CIRCUIT PLANE LAYER VIA CONNECTION TO GROUND PLANE C1 R1 C3 R3
FIGURE 4. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS
The switching components should be placed close to the ISL6526, ISL6526A first. Minimize the length of the connections between the input capacitors, CIN, and the power switches by placing them nearby. Position both the ceramic and bulk input capacitors as close to the upper MOSFET drain as possible. Position the output inductor and output capacitors between the upper MOSFET and lower MOSFET and the load. The critical small signal components include any bypass capacitors, feedback components, and compensation components. Position the bypass capacitor, CBP, close to the VCC pin with a via directly to the ground plane. Place the PWM converter compensation components close to the FB and COMP pins. The feedback resistors for both regulators should also be located as close as possible to the relevant FB pin with vias tied straight to the ground plane as required.
ISL6526, ISL6526A
Feedback Compensation
Figure 5 highlights the voltage-mode control loop for a synchronous-rectified buck converter. The output voltage (VOUT) is regulated to the Reference voltage level. The error amplifier (Error Amp) output (VE/A) is compared with the oscillator (OSC) triangular wave to provide a pulsewidth modulated (PWM) wave with an amplitude of VIN at the PHASE node. The PWM wave is smoothed by the output filter (LO and CO). The modulator transfer function is the small-signal transfer function of VOUT/VE/A . This function is dominated by a DC Gain and the output filter (LO and CO), with a double pole break frequency at FLC and a zero at FESR . The DC Gain of the modulator is simply the input voltage (VIN) divided by the peak-to-peak oscillator voltage VOSC .
DRIVER VIN LO DRIVER PHASE CO VOUT
relate the compensation network's poles, zeros and gain to the components (R1 , R2 , R3 , C1 , C2 , and C3) in Figure 5. Use these guidelines for locating the poles and zeros of the compensation network: 1. Pick gain (R2/R1) for desired converter bandwidth. 2. Place first zero below filter's double pole (~75% FLC). 3. Place second zero at filter's double pole. 4. Place first pole at the ESR zero. 5. Place second pole at half the switching frequency. 6. Check gain against error amplifier's open-loop gain. 7. Estimate phase margin - repeat if necessary.
Compensation Break Frequency Equations
1 F Z1 = --------------------------------2 x R 2 x C 2 1 F Z2 = -----------------------------------------------------2 x ( R 1 + R 3 ) x C 3 1 F P1 = ------------------------------------------------------- C 1 x C 2 2 x R 2 x --------------------- C1 + C2 1 F P2 = ----------------------------------2 x R 3 x C 3 (EQ. 4)
OSC PWM COMPARATOR VOSC +
ZFB VE/A + ERROR AMP ZIN REFERENCE
ESR (PARASITIC)
DETAILED COMPENSATION COMPONENTS C1 C2 R2 ZFB ZIN C3 R1 FB + ISL6526, ISL6526A REFERENCE R3 VOUT
Figure 6 shows an asymptotic plot of the DC/DC converter's gain vs frequency. The actual Modulator Gain has a high gain peak due to the high Q factor of the output filter and is not shown in Figure 6. Using the above guidelines should give a Compensation Gain similar to the curve plotted. The open loop error amplifier gain bounds the compensation gain. Check the compensation gain at FP2 with the capabilities of the error amplifier. The Closed Loop Gain is constructed on the graph of Figure 6 by adding the Modulator Gain (in dB) to the Compensation Gain (in dB). This is equivalent to multiplying the modulator transfer function to the compensation transfer function and plotting the gain. The compensation gain uses external impedance networks ZFB and ZIN to provide a stable, high bandwidth (BW) overall loop. A stable control loop has a gain crossing with -20dB/decade slope and a phase margin greater than 45 degrees. Include worst case component variations when determining phase margin.
FZ1 100 FZ2 FP1 FP2 OPEN LOOP ERROR AMP GAIN V IN 20 log ----------------- V OSC
COMP
FIGURE 5. VOLTAGE-MODE BUCK CONVERTER COMPENSATION DESIGN
80 60
Modulator Break Frequency Equations
GAIN (dB)
40 20 0 -20 -40 -60 R2 20 log ------- R1 MODULATOR GAIN
1 F LC = ----------------------------------------2 x L O x C O
1 F ESR = -----------------------------------------2 x ESR x C O
COMPENSATION GAIN
The compensation network consists of the error amplifier (internal to the ISL6526, ISL6526A) and the impedance networks ZIN and ZFB. The goal of the compensation network is to provide a closed loop transfer function with the highest 0dB crossing frequency (f0dB) and adequate phase margin. Phase margin is the difference between the closed loop phase at f0dB and 180 degrees. The equations below
LOOP GAIN FLC 1K FESR 10K 100K 1M 10M
10
100
FREQUENCY (Hz)
FIGURE 6. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
10
FN9055.8 March 20, 2007
ISL6526, ISL6526A Component Selection Guidelines
Charge Pump Capacitor Selection
A capacitor across pins CT1 and CT2 is required to create the proper bias voltage for the ISL6526, ISL6526A when operating the IC from 3.3V. Selecting the proper capacitance value is important so that the bias current draw and the current required by the MOSFET gates do not overburden the capacitor. A conservative approach is presented in the following equation.
I BiasAndGate C PUMP = ------------------------------------ x 1.5 V CC x f s
of the ripple current. The ripple voltage and current are approximated by the following equations:
I = VIN - VOUT fs x L x VOUT VIN VOUT = I x ESR (EQ. 6)
Increasing the value of inductance reduces the ripple current and voltage. However, the large inductance values reduce the converter's response time to a load transient. One of the parameters limiting the converter's response to a load transient is the time required to change the inductor current. Given a sufficiently fast control loop design, the ISL6526, ISL6526A will provide either 0% or 100% duty cycle in response to a load transient. The response time is the time required to slew the inductor current from an initial current value to the transient current level. During this interval the difference between the inductor current and the transient current level must be supplied by the output capacitor. Minimizing the response time can minimize the output capacitance required. The response time to a transient is different for the application of load and the removal of load. The following equations give the approximate response time interval for application and removal of a transient load:
tRISE = L x ITRAN VIN - VOUT tFALL = L x ITRAN VOUT (EQ. 7)
(EQ. 5)
Output Capacitor Selection
An output capacitor is required to filter the output and supply the load transient current. The filtering requirements are a function of the switching frequency and the ripple current. The load transient requirements are a function of the slew rate (di/dt) and the magnitude of the transient load current. These requirements are generally met with a mix of capacitors and careful layout. Modern digital ICs can produce high transient load slew rates. High frequency capacitors initially supply the transient and slow the current load rate seen by the bulk capacitors. The bulk filter capacitor values are generally determined by the ESR (Effective Series Resistance) and voltage rating requirements rather than actual capacitance requirements. High frequency decoupling capacitors should be placed as close to the power pins of the load as physically possible. Be careful not to add inductance in the circuit board wiring that could cancel the usefulness of these low inductance components. Consult with the manufacturer of the load on specific decoupling requirements. Use only specialized low-ESR capacitors intended for switching-regulator applications for the bulk capacitors. The bulk capacitor's ESR will determine the output ripple voltage and the initial voltage drop after a high slew-rate transient. An aluminum electrolytic capacitor's ESR value is related to the case size with lower ESR available in larger case sizes. However, the Equivalent Series Inductance (ESL) of these capacitors increases with case size and can reduce the usefulness of the capacitor to high slew-rate transient loading. Unfortunately, ESL is not a specified parameter. Work with your capacitor supplier and measure the capacitor's impedance with frequency to select a suitable component. In most cases, multiple electrolytic capacitors of small case size perform better than a single large case capacitor.
where: ITRAN is the transient load current step, tRISE is the response time to the application of load, and tFALL is the response time to the removal of load. The worst case response time can be either at the application or removal of load. Be sure to check both of these equations at the minimum and maximum output levels for the worst case response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage overshoot across the MOSFETs. Use small ceramic capacitors for high frequency decoupling and bulk capacitors to supply the current needed each time Q1 turns on. Place the small ceramic capacitors physically close to the MOSFETs and between the drain of Q1 and the source of Q2 . The important parameters for the bulk input capacitor are the voltage rating and the RMS current rating. For reliable operation, select the bulk capacitor with voltage and current ratings above the maximum input voltage and largest RMS current required by the circuit. The capacitor voltage rating should be at least 1.25 times greater than the maximum input voltage and a voltage rating of 1.5 times is a conservative guideline. The RMS current rating requirement for the input capacitor of a buck regulator is approximately 1/2 the DC load current.
Output Inductor Selection
The output inductor is selected to meet the output voltage ripple requirements and minimize the converter's response time to the load transient. The inductor value determines the converter's ripple current and the ripple voltage is a function
11
FN9055.8 March 20, 2007
ISL6526, ISL6526A
The maximum RMS current required by the regulator may be closely approximated through the following equation:
I RMS = V OUT V IN - V OUT V OUT 2 2 1 ------------- x I OUT + ----- x ---------------------------- x ------------- V IN V IN 12 L x f s MAX (EQ. 8)
MAX
For a through hole design, several electrolytic capacitors may be needed. For surface mount designs, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating. These capacitors must be capable of handling the surge-current at power-up. Some capacitor series available from reputable manufacturers are surge current tested.
Given the reduced available gate bias voltage (5V), logiclevel or sub-logic-level transistors should be used for both N-MOSFETs. Caution should be exercised with devices exhibiting very low VGS(ON) characteristics. The shootthrough protection present aboard the ISL6526, ISL6526A may be circumvented by these MOSFETs if they have large parasitic impedances and/or capacitances that would inhibit the gate of the MOSFET from being discharged below its threshold level before the complementary MOSFET is turned on.
Bootstrap Component Selection
External bootstrap components, a diode and capacitor, are required to provide sufficient gate enhancement to the upper MOSFET. The internal MOSFET gate driver is supplied by the external bootstrap circuitry as shown in Figure 7. The boot capacitor, CBOOT, develops a floating supply voltage referenced to the PHASE pin. This supply is refreshed each cycle, when DBOOT conducts, to a voltage of CPVOUT less the boot diode drop, VD, plus the voltage rise across QLOWER.
ISL6526, ISL6526A CPVOUT DBOOT + VD CBOOT UGATE PHASE QUPPER NOTE: VG-S = VCC -VD QLOWER NOTE: VG-S = VCC GND VIN
MOSFET Selection/Considerations
The ISL6526, ISL6526A require two N-Channel power MOSFETs. These should be selected based upon rDS(ON) , gate supply requirements, and thermal management requirements. In high-current applications, the MOSFET power dissipation, package selection and heatsink are the dominant design factors. The power dissipation includes two loss components; conduction loss and switching loss. The conduction losses are the largest component of power dissipation for both the upper and the lower MOSFETs. These losses are distributed between the two MOSFETs according to duty factor. The switching losses seen when sourcing current will be different from the switching losses seen when sinking current. When sourcing current, the upper MOSFET realizes most of the switching losses. The lower switch realizes most of the switching losses when the converter is sinking current (see equations on next page). These equations assume linear voltage-current transitions and do not adequately model power loss due the reverse-recovery of the upper and lower MOSFET's body diode. The gate-charge losses are dissipated by the ISL6526, ISL6526A and don't heat the MOSFETs. However, large gatecharge increases the switching interval, tSW which increases the MOSFET switching losses. Ensure that both MOSFETs are within their maximum junction temperature at high ambient temperature by calculating the temperature rise according to package thermal-resistance specifications. A separate heatsink may be necessary depending upon MOSFET power, package type, ambient temperature and air flow. Losses while Sourcing current
2 1 P UPPER = Io x r DS ( ON ) x D + -- Io x V IN x t SW x f s 2 PLOWER = Io2 x rDS(ON) x (1 - D)
BOOT
+
LGATE
FIGURE 7. UPPER GATE DRIVE BOOTSTRAP
Just after the PWM switching cycle begins and the charge transfer from the bootstrap capacitor to the gate capacitance is complete, the voltage on the bootstrap capacitor is at its lowest point during the switching cycle. The charge lost on the bootstrap capacitor will be equal to the charge transferred to the equivalent gate-source capacitance of the upper MOSFET as shown:
Q GATE = C BOOT x ( V BOOT1 - V BOOT2 ) (EQ. 10)
Losses while Sinking current
PUPPER = Io2 x rDS(ON) x D
2 1 P LOWER = Io x r DS ( ON ) x ( 1 - D ) + -- Io x V IN x t SW x f s 2
where QGATE is the maximum total gate charge of the upper MOSFET, CBOOT is the bootstrap capacitance, VBOOT1 is the bootstrap voltage immediately before turn-on, and VBOOT2 is the bootstrap voltage immediately after turn-on. The bootstrap capacitor begins its refresh cycle when the gate drive begins to turn-off the upper MOSFET. A refresh cycle
Where: D is the duty cycle = VOUT / VIN , tSW is the combined switch ON and OFF time, and fs is the switching frequency. (EQ. 9)
12
FN9055.8 March 20, 2007
ISL6526, ISL6526A
ends when the upper MOSFET is turned on again, which varies depending on the switching frequency and duty cycle. The minimum bootstrap capacitance can be calculated by rearranging the previous equation and solving for CBOOT.
Q GATE C BOOT = ---------------------------------------------------V BOOT1 - V
BOOT2
drop across the bootstrap capacitor to 1V results in a value of no less than 0.1F. The tolerance of the ceramic capacitor should also be considered when selecting the final bootstrap capacitance value. A fast recovery diode is recommended when selecting a bootstrap diode to reduce the impact of reverse recovery charge loss. Otherwise, the recovery charge, QRR, would have to be added to the gate charge of the MOSFET and taken into consideration when calculating the minimum bootstrap capacitance.
(EQ. 11)
Typical gate charge values for MOSFETs considered in these types of applications range from 20 to 100nC. Since the voltage drop across QLOWER is negligible, VBOOT1 is simply VCPVOUT - VD. A schottky diode is recommended to minimize the voltage drop across the bootstrap capacitor during the on-time of the upper MOSFET. Initial calculations with VBOOT2 no less than 4V will quickly help narrow the bootstrap capacitor range. For example, consider an upper MOSFET is chosen with a maximum gate charge, Qg, of 100nC. Limiting the voltage
ISL6526, ISL6526A DC/DC Converter Application Circuit
Figure 8 shows an application circuit of a DC/DC Converter. Detailed information on the circuit, including a complete Billof-Materials and circuit board description, can be found in Application Note AN9994.
3.3V C1 0.1F GND TP1 4 CT1 11 VCC OCSET ISL6526, ISL6526A CPVOUT 5 CT2 10 1 BOOT 13 C7 UGATE PHASE ENABLE 9 ENABLE LGATE COMP 8 C10 33pF R2 C11 FB 7 R3 2.26k R4 R5 1.07k 124 C12 8200pF GND 14 12 L1 2.5V @ 5A 3 D1 C5 10F CERAMIC 0.1F U1 6 TP3 R1 9.76k C2 1000pF C3
C4 0.22F
C6 1F
CPGND GND
2 Q1
C8,9
6.49k 5600pF
FIGURE 8. 3.3V TO 2.5V 5A DC/DC CONVERTER Component Selection Notes: C3,8,9 - Each 150F, Panasonic EEF-UE0J151R or Equivalent. D1 - 30mA Schottky Diode, MA732 or Equivalent L1 - 1H Inductor, Panasonic P/N ETQ-P6F1ROSFA or Equivalent. Q1 - Fairchild MOSFET; ITF86110DK8.
13
FN9055.8 March 20, 2007
ISL6526, ISL6526A Small Outline Plastic Packages (SOIC)
N INDEX AREA H E -B1 2 3 SEATING PLANE -AD -CA h x 45o 0.25(0.010) M BM
M14.15 (JEDEC MS-012-AB ISSUE C)
14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A
L
MILLIMETERS MIN 1.35 0.10 0.33 0.19 8.55 3.80 5.80 0.25 0.40 14 0o MAX 1.75 0.25 0.51 0.25 8.75 4.00 6.20 0.50 1.27 8o NOTES 9 3 4 5 6 7 Rev. 0 12/93
MIN 0.0532 0.0040 0.013 0.0075 0.3367 0.1497 0.2284 0.0099 0.016 14 0o
MAX 0.0688 0.0098 0.020 0.0098 0.3444 0.1574 0.2440 0.0196 0.050 8o
A1 B C D E e
C
A1 0.10(0.004)
e
B 0.25(0.010) M C AM BS
0.050 BSC
1.27 BSC
H h L N
NOTES: 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
14
FN9055.8 March 20, 2007
ISL6526, ISL6526A Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP)
L16.5x5B
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220VHHB ISSUE C) MILLIMETERS SYMBOL A A1 A2 A3 b D D1 D2 E E1 E2 e k L L1 N Nd Ne P 0.25 0.35 2.95 2.95 0.28 MIN 0.80 NOMINAL 0.90 0.20 REF 0.33 5.00 BSC 4.75 BSC 3.10 5.00 BSC 4.75 BSC 3.10 0.80 BSC 0.60 16 4 4 0.60 12 0.75 0.15 3.25 3.25 0.40 MAX 1.00 0.05 1.00 NOTES 9 9 5, 8 9 7, 8 9 7, 8 8 10 2 3 3 9 9 Rev. 1 10/02 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 15
FN9055.8 March 20, 2007

▲Up To Search▲

Price & Availability of ISL652607

	To Download ISL652607 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .