View NLP150H-9610_654852.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NLP150H SERIES
Single, dual, triple and quad output
* * * * * * * * 6.5 x 3.0 x 3.06 package (2U applications) Smallest industry footprint EN61000-3-2 compliant Overvoltage and short circuit protection 150W with 150LFM EN55022, EN55011 conducted emissions level B EN61000-4-2, -3, -4, -5, -6 immunity compliant UL, VDE and CSA safety approvals
Patent No. 5600546 and 5652700
[ 2 YEAR WARRANTY ]
The NLP150H series is a 150W universal input AC/DC power supply in a 6.5 x 3.0 x 3.06 inch package for use in 2U applications. The series has the smallest standard 125 to 150W footprint in the industry, has input harmonic current emission correction as standard and has 3.3V models to support the semiconductor industry's transition from 5V to lower operating voltages. The NLP150H provides 150W of output power with 150LFM of air. Standard features include overvoltage and short circuit protection. The series has an enclosure with fan option that does not change the overall package size. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B and complies to EN61000-4-2,-3,-4, -5 and -6 immunity standards. The NLP150H series is designed for use in low power data networking, computer and telecom applications such as hubs, routers, file servers, graphic workstations, storage peripherals and PABX's.
SPECIFICATION
OUTPUT SPECIFICATIONS Total regulation (Line and load) Rise time Transient response
All specifications are typical at nominal input, full load at 25C unless otherwise stated GENERAL SPECIFICATIONS 2.0% 2.0% 5.0% 250ms, max. 5.0% or 250mV max. dev., 1ms max. recovery to 1% 0.02%/C Hold-up time Efficiency Isolation voltage Switching frequency Approvals and standards (See Note 6) Weight Size Open-frame With cover and fan Input/output Input/chassis Fixed 120VAC, 60Hz 16ms @ 150W 72% typical 3000VAC 1500VAC 100kHz, 10kHz VDE0805, EN60950 IEC950, UL1950 CSA C22.2 No. 950 680g (24 oz) 900g (31.77 oz)
Single outputs Multiple outputs (5V, 3.3V) Auxiliary outputs At turn-on Main output 25% step at 0.1A/s
Temperature coefficient Overvoltage protection Short circuit protection Minimum output current Remote sense Outputs 1 and 2
Single outputs and 125% of nominal multi outputs 1 and 2 10% tolerance Continuous Yes, see table 0.5V max. drop
Open-frame 6.5 x 3.0 x 3.06 in. With cover and fan 7.5 x 3.0 x 3.10 in. MIL-HDBK-217F > 200,000 hours
MTBF
INPUT SPECIFICATIONS Input voltage range Input frequency range Input surge current (cold start) Safety ground leakage current Input current Input fuse 120VAC 230VAC 120VAC, 60Hz 230VAC, 50Hz 120VAC UL, IEC approved
(7)
ENVIRONMENTAL SPECIFICATIONS 90 to 264VAC 47Hz to 63Hz 19A max. 38A max. 0.7mA 1.4mA 2.4A max. 250VAC 6.3A Relative humidity Altitude Vibration (See Note 4) Shock Perf. Perf. Perf. Perf. Perf. Perf. Level B Level A criteria 1 criteria 1 criteria 1 criteria 1 criteria 1 criteria 1 Thermal performance 0C to +50C ambient, 150W 150LFM forced air Non-operating -40C to +85C +50C to +70C, Derate to 150LFM forced air 50% load Peak (0C to +50C, 60s) (See Note 2) Non-condensing Operating Non-operating 5Hz to 500Hz per MIL-STD-810E 5% to 95% RH 10,000 feet max. 30,000 feet max. 2.4G rms peak 516.4 Part IV
Universal input
EMC CHARACTERISTICS Conducted emissions Radiated emissions ESD air ESD contact Surge Fast transients Radiated immunity Conducted immunity
EN55022, FCC part 15 EN55022, FCC part 15 EN61000-4-2, level 3 EN61000-4-2, level 4 EN61000-4-5, level 3 EN61000-4-4, level 3 EN61000-4-3, level 3 EN61000-4-6, level 3
PAGE 58
LOW TO MEDIUM POWER AC/DC POWER SUPPLIES
|
125-150W AC/DC
125 to 150 Watt AC/DC universal input switch mode power supplies
OUTPUT VOLTAGE 5V 12V 13.8V 24V 48V 5V (VA) 3.3V (VB) 5V (VA) 12V (VB) -12V (VC) 5V (VA) 15V (VB) -15V (VC) 5V (VA) 3.3V (VB) 12V (VC) -12V (VD) 5V (VA) 12V (VB) 24V (VC) -12V (VD) Notes
150LFM forced air cooling (150W max.). Peak output current lasting less than 60 seconds with duty cycle less than 5%. During peak loading, output voltage may exceed total regulation limits. 3 Figure is peak-to-peak. Output noise measurements are made across a 20MHz bandwidth using a 12 inch twisted pair, terminated with a 47F capacitor. 4 Three orthogonal axes, random vibration 10 minutes for each axes, 2.4G rms 5Hz to 500Hz. 5 CAUTION: Allow a minimum of 1 second after disconnecting line power when making thermal measurements. 6 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 7 For system EMI compliance, a ground choke may be required before connecting the ground wire to the chassis. 8 To order the NLP150H with an enclosure, add the suffix 'E' to the model number e.g. NLP150H-96XXE. See page 61 for details. 9 For single output models, J2 and J3 must be connected in parallel for proper operation. To maintain specified regulation on enclosed single output models and on VA and VB of enclosed multiple output models, the remote sense pins should be used. 10 For optimum reliability no part of the heatsink should exceed 120C and no semi-conductor case temperature should exceed 135C. 1 2
OUTPUT CURRENT RIPPLE MIN 3A 1.25A 1.1A 0.63A 0.32A 1.5A 1.5A 1.5A 0.63A 0A 1.5A 0.5A 0A 1.5A 1.2A 0A 0A 1.5A 0.63A 0A 0A MAX
(1) (3)
TOTAL REGULATION
MODEL NUMBERS
(8,9)
PEAK 36A 15A 13A 7.5A
(2)
30A 12.5A 11A 6.3A 3.2A 15A 15A 15A 6.3A 0.8A 15A 5A 0.8A 15A 12A 1.25A 0.8A 15A 6.3A 0.8A 0.8A
50mV 120mV 120mV 240mV 480mV 50mV 50mV 50mV 120mV 120mV 50mV 150mV 150mV 50mV 50mV 120mV 120mV 50mV 120mV 240mV 120mV
2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 5.0% 2.0% 2.0% 5.0% 2.0% 2.0% 5.0% 5.0% 2.0% 2.0% 5.0% 5.0%
NLP150H-9605 NLP150H-9612 NLP150H-9614 NLP150H-9624 NLP150H-9617 NLP150H-9690
1
3.75A 18A 18A 18A 7.5A 1.0A 18A 6A 1.0A 18A 15A 1.25A 1.0A 18A 7.5A 1.0A 1.0A
NLP150H-9608
NLP150H-9610
NLP150H-9691
NLP150H-9602
DERATING CURVE
Output Power (Watts)
150W
150 LFM FORCED AIR COOLING
75W
0C 10C
20C
30C
40C
50C
60C
70C
International Safety Standard Approvals
VDE0805/EN60950/IEC950 File No. 10401-3336-0108 Licence No. 98724 UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062C
http://www.artesyn.com
PAGE 59
125-150W AC/DC
|
LOW TO MEDIUM POWER AC/DC POWER SUPPLIES
125 to 150 Watt AC/DC universal input switch mode power supplies
Open-frame mechanical drawing
6.50 (165.1) 3.06 (77.72) 0.35 (8.89) 6.085 (154.559) 0.19 (4.826) 0.59 (14.99)
3.000 (76.2) J1 AC Input 2.300 (58.42) J1 AC Input L N G
Va sense J12 Power Good J13 J2 Va Power
J12 J13 J7 Int Fan Power J6 Vb Sense J3 Vb-d Power 1.825 (46.355) 3.00 (76.20) J2
J7 J6 J3
Pin # 1 Typ. (*) 0.138-32-UNC-2B (10 Places) (3 Each Side, 4 on Bottom) 1/4" (6.35) Max. Thread Penetration - Typ.
5.625 (142.875)
0.35 (8.89)
1.750 (44.45) Third Angle Projection 0.94 (23.876)
Input pin assignment (J1) (Open-frame only)
The input connector is a standard Leoco 5-pin polarized header type connector with 0.156 inch spacing (3940P05V000) or equivalent. The recommended mating connector socket is the Leoco 3940 series (3940S050000) or equivalent. The pin assignment is summarized below. Pin numbering is from right to left facing the connector.
5.500 (139.7) 5.175 (131.445)
0.45 (11.43)
0.156 (4 Places) (4.191)
2.275 (57.785)
1.775 (45.085)
INPUT PIN CONNECTIONS J1 Pin 1 Ground Pin 2 No Pin Pin 3 Neutral (AC Low) Pin 4 No Pin Pin 5 Line (AC High) Output pin assignment (J2, J3)
The output power connectors are two standard Leoco 6-pin polarized header type connectors with 0.156 inch spacing (3940P06V000) or equivalent. The recommended mating connector sockets are the Leoco 3940 series (3940S060000) or equivalents. The pin assignment is summarized below. Pin numbering is from right to left facing the connector. For single output models, J2 and J3 must be connected in parallel for proper operation.
6.085 (154.559) 0.19 (4.826) ALL DIMENSIONS IN INCHES (mm) Tolerances unless otherwise specified .xx = 0.02 .xxx = 0.010
0.37 Ref. (9.398)
PIN CONNECTIONS J2 (ALL MODELS) Pin 1 VA Pin 2 VA Pin 3 VA Pin 4 Return Pin 5 Return Pin 6 Return
J3 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6
OUTPUT PIN CONNECTIONS SINGLE (9) DUAL TRIPLE VA VB VC VA VB VB VA VB VB Return Return Return Return Return Return Return Return No Pin
QUAD VD VB VB Return Return VC
Signal pin assignment (J6, J12, J13)
Three two-pin Molex 6373 type connectors (P/N: 22-23-2021) with 0.100 inch spacing or equivalent are used for remote sensing and power good signal. The pin assignment is summarized in the following tables. Pin numbering is from right to left facing the connector.
PIN CONNECTIONS J13 (ALL MODELS) Pin 1 VA Return Pin 2 Power Good
PIN CONNECTIONS J12 (ALL MODELS) Pin 1 - Sense VA Pin 2 + Sense VA
PIN CONNECTIONS J6 (ALL MODELS) Pin 1 - Sense VB Pin 2 + Sense VB
PAGE 60
LOW TO MEDIUM POWER AC/DC POWER SUPPLIES
|
125-150W AC/DC
125 to 150 Watt AC/DC universal input switch mode power supplies
Enclosed mechanical drawing
0.691 (17.55) IEC - 380 AC INLET 40mm INTERNAL FAN 0.35 (8.89) 7.50 (190.50) 5.175 (131.445) 0.48 (12.19) 5.500 (139.70) 0.38 (9.65) 0.59 (14.99) 3.10 (78.74)
0.50 (12.70)
1.50 (38.10) 2.000 (50.8) 2.80 (71.12) 2.275 2.300 (57.785) (58.42) AIR FLOW 1.775 1.825 (45.09) (46.36) 3.00 (76.20)
1
2.09 (53.09) 0.138 (3.505) 32-UNC-2B (2 PLACES)
0.138 (3.505) 32-UNC-2B (10 PLACES) (3 EACH SIDE, 4 ON BOTTOM) 1/4" max. Thread penetration -Typ.
6.05 (153.67)
0.22 (5.59) 0.41 (10.41)
0.156 (3.96) (4 PLS)
2.57 (65.28)
0.63 (16.00)
5.625 (142.875)
THIRD ANGLE PROJECTION
1.750 (44.45)
OUTPUT CABLE ASSEMBLY P1 MAIN OUTPUT - 6 INCHES LONG P4-6 SIG OUTPUTS - 8 INCHES LONG
0.94 (23.88)
0.14 (3.56)
6.50 (165.1)
ALL DIMENSIONS IN INCHES (mm) Tolerances unless otherwise specified .xx = 0.02 .xxx = 0.010
P1 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14
OUTPUT PIN CONNECTIONS SINGLE DUAL TRIPLE Return Return Return Return Return Return Return Return Return VA VB VB VA VB VB VA VB VB VA VB VC Return Return No Connect. Return Return Return Return Return Return Return Return Return VA VA VA VA VA VA VA VA VA
Output pin assignment (P1) QUAD Return Return Return VB VB VB VD VC Return Return Return VA VA VA
Molex mini-fit connector (P/N: 39-01-2145) or equivalent with Molex crimp terminals (P/N: 39-00-0059) or equivalent. The pin assignment is summarized below.
P1 OUTPUT POWER CONNECTOR 8 1 14 7
MATING END OF CONNECTOR SHOWN
Signal pin assignment (P4, P5, P6)
Three two-pin Molex mini-fit connectors (P/N: 39-01-4031) with 0.165 inch spacing or equivalent with Molex crimp terminals (P/N: 39-00-0039) or equivalent. The pin assignment is summarized in the following tables. Pin numbering is from right to left facing the connector.
P4 Va Sense
P5 Power Good
P6 Vb Sense
1
3
1
3
1
3
PIN CONNECTIONS P4 (ALL MODELS) Pin 1 Pin 2 Pin 3 - Sense VA + Sense VA No Connection
PIN CONNECTIONS P5 (ALL MODELS) Pin 1 Pin 2 Pin 3 VA Return No Connection Power Good
PIN CONNECTIONS P6 (ALL MODELS) Pin 1 Pin 2 Pin 3 No Connection - Sense VB + Sense VB
DS_NLP150H_20010226PDF
Data Sheet (c) Artesyn Technologies(R) 2000 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
http://www.artesyn.com
PAGE 61

▲Up To Search▲

Price & Availability of NLP150H-9610

	To Download NLP150H-9610 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .