Part Number Hot Search : 
RF081 SDA294D STPS8L30 S18LA ST16600 MAX8563 080207R0 3SK0270
Product Description
Full Text Search
 

To Download IS62WV10248BLL-70BI Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 IS62WV10248BLL
1M x 8 LOW VOLTAGE, ULTRA LOW POWER CMOS STATIC RAM
FEATURES
* High-speed access time: 55ns, 70ns * CMOS low power operation: 36 mW (typical) operating 12 W (typical) CMOS standby * TTL compatible interface levels * Single power supply: 2.5V--3.6V VDD (IS62WV10248BLL) * Fully static operation: no clock or refresh required * Three state outputs * Industrial temperature available * Lead-free available
ISSI
MARCH 2006
(R)
DESCRIPTION
The ISSI IS62WV10248BLL is a high-speed, 8M bit static RAMs organized as 1M words by 8 bits. It is fabricated using ISSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields high-performance and low power consumption devices. When CS1 is HIGH (deselected) or when CS2 is LOW (deselected), the device assumes a standby mode at which the power dissipation can be reduced down with CMOS input levels. Easy memory expansion is provided by using Chip Enable and Output Enable inputs. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IS62WV10248BLL is packaged in the JEDEC standard 48-pin mini BGA (7.2mm x 8.7mm).
FUNCTIONAL BLOCK DIAGRAM
A0-A19
DECODER
1M x 8 MEMORY ARRAY
VDD GND I/O DATA CIRCUIT
I/O0-I/O7
COLUMN I/O
CS2 CS1 OE WE
Copyright (c) 2006 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products.
CONTROL CIRCUIT
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
1
IS62WV10248BLL
ISSI
(R)
PIN DESCRIPTIONS
A0-A19 CS1 CS2 OE WE I/O0-I/O7 NC VDD GND Address Inputs Chip Enable 1 Input Chip Enable 2 Input Output Enable Input Write Enable Input Input/Output No Connection Power Ground
PIN CONFIGURATION 48-pin mini BGA (B) (7.2mm x 8.7mm)
1
A B C D E F G H
NC
2
OE
3
A0
4
A1
5
A2
6
CS2
NC
NC
A3
A4
CS1
NC
I/O0
NC
A5
A6
NC
I/O4
GND
I/O1
A17
A7
I/O5
VDD
VDD
I/O2
NC
A16
I/O6
GND
I/O3
NC
A14
A15
NC
I/O7
NC
NC
A12
A13
WE
NC
A18
A8
A9
A10
A11
A19
2
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
IS62WV10248BLL
ISSI
CS1 H X L L L CS2 X L H H H OE X X H L X I/O Operation High-Z High-Z High-Z DOUT DIN VDD Current ISB1, ISB2 ISB1, ISB2 ICC ICC ICC
(R)
TRUTH TABLE
Mode Not Selected (Power-down) Output Disabled Read Write WE X X H H L
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VTERM VDD TSTG PT Parameter Terminal Voltage with Respect to GND VDD Related to GND Storage Temperature Power Dissipation Value -0.2 to VDD+0.3 -0.2 to +3.8 -65 to +150 1.0 Unit V V C W
Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
OPERATING RANGE (VDD)
Range Commercial Industrial Ambient Temperature 0C to +70C -40C to +85C IS62WV10248BLL 2.5V - 3.6V 2.5V - 3.6V
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Symbol VOH VOL VIH VIL(1) ILI ILO Parameter Output HIGH Voltage Output LOW Voltage Input HIGH Voltage Input LOW Voltage Input Leakage Output Leakage GND VIN VDD GND VOUT VDD, Outputs Disabled Test Conditions IOH = -1 mA IOL = 2.1 mA VDD 2.5-3.6V 2.5-3.6V 2.5-3.6V 2.5-3.6V Min. 2.2 -- 2.2 -0.2 -1 -1 Max. -- 0.4 VDD + 0.3 0.6 1 1 Unit V V V V A A
Notes: 1. VIL (min.) = -1.0V for pulse width less than 10 ns.
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
3
IS62WV10248BLL
ISSI
Conditions VIN = 0V VOUT = 0V Max. 8 10 Unit pF pF
(R)
CAPACITANCE(1)
Symbol CIN COUT Parameter Input Capacitance Input/Output Capacitance
Note: 1. Tested initially and after any design or process changes that may affect these parameters.
AC TEST CONDITIONS
Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load IS62WV10248BLL (Unit) 0.4 to VDD-0.3V 5 ns VREF See Figures 1 and 2
IS62WV10248BLL 2.5V - 3.6V R1() R2() VREF VTM 1029 1728 1.5V 2.8V
AC TEST LOADS
R1 VTM
VTM R1
OUTPUT 30 pF Including jig and scope R2
OUTPUT 5 pF Including jig and scope R2
Figure 1
Figure 2
4
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
IS62WV10248BLL
ISSI
Test Conditions VDD = Max., IOUT = 0 mA, f = fMAX VDD = Max., CS1 = 0.2V WE = VDD -0.2V CS2 = VDD -0.2V, f = 1MHz VDD = Max., VIN = VIH or VIL CS1 = VIH , CS2 = VIL, f = 1 MHZ VDD = Max., CS1 VDD - 0.2V, CS2 0.2V, VIN VDD - 0.2V, or VIN 0.2V, f = 0 Com. Ind. Com. Ind. Com. Ind. Max. 55 30 35 5 5 0.3 0.3 Max. 70 25 30 5 5 0.3 0.3 Unit mA mA
(R)
POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) IS62WV10248BLL
Symbol Parameter ICC ICC1 VDD Dynamic Operating Supply Current Operating Supply Current TTL Standby Current (TTL Inputs)
ISB1
mA
ISB2
CMOS Standby Current (CMOS Inputs)
Com. Ind. typ.(1)
20 25 3
20 25 3
A
Note: 1. Typical Values are measured at VDD = 3.0V, TA = 25oC and not 100% tested.
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
5
IS62WV10248BLL
READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range)
Symbol Parameter Read Cycle Time Address Access Time Output Hold Time CS1/CS2 Access Time OE Access Time
(2)
ISSI
55 ns Min. Max. 55 -- 10 -- -- -- 5 0 10 -- 55 -- 55 25 20 -- 20 -- 70 ns Min. Max. 70 -- 10 -- -- -- 5 0 10 -- 70 -- 70 35 25 -- 25 -- Unit ns ns ns ns ns ns ns ns ns
(R)
tRC tAA tOHA tACS1/tACS2 tDOE tHZOE tLZOE(2) tHZCS1/tHZCS2 tLZCS1/tLZCS2
(2) (2)
OE to High-Z Output OE to Low-Z Output CS1/CS2 to High-Z Output CS1/CS2 to Low-Z Output
Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0.4V to VDD-0.3V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured 500 mV from steady-state voltage. Not 100% tested.
AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CS1 = OE = VIL, CS2 = WE = VIH)
tRC
ADDRESS
tAA tOHA tOHA
DATA VALID
DOUT
PREVIOUS DATA VALID
6
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
IS62WV10248BLL
AC WAVEFORMS READ CYCLE NO. 2(1,3) (CS1, CS2, OE Controlled)
tRC
ISSI
(R)
ADDRESS
tAA tOHA
OE
tDOE tHZOE
CS1
tACS1/tACS2
tLZOE
CS2
tLZCS1/ tLZCS2
HIGH-Z
tHZCS
DATA VALID
DOUT
Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CS1= VIL. CS2=WE=VIH. 3. Address is valid prior to or coincident with CS1 LOW and CS2 HIGH transition.
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
7
IS62WV10248BLL
ISSI
55 ns Min. Max. 55 45 45 0 0 40 25 0 -- 5 -- -- -- -- -- -- -- -- 25 -- 70 ns Min. Max. 70 60 60 0 0 50 30 0 -- 5 -- -- -- -- -- -- -- -- 25 -- Unit ns ns ns ns ns ns ns ns ns ns
(R)
WRITE CYCLE SWITCHING CHARACTERISTICS(1,2) (Over Operating Range)
Symbol Parameter Write Cycle Time
tWC
tSCS1/tSCS2 CS1/CS2 to Write End tAW Address Setup Time to Write End tHA tSA tPWE tSD
(4)
Address Hold from Write End Address Setup Time WE Pulse Width Data Setup to Write End Data Hold from Write End WE LOW to High-Z Output WE HIGH to Low-Z Output
tHD tHZWE(3) tLZWE
Notes:
(3)
1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0.4V to VDD0.3V and output loading specified in Figure 1. 2. The internal write time is defined by the overlap of CS1 LOW, CS2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 3. Tested with the load in Figure 2. Transition is measured 500 mV from steady-state voltage. Not 100% tested. 4. tPWE > tHZWE + tSD when OE is LOW.
AC WAVEFORMS WRITE CYCLE NO. 1 (CS1/CS2 Controlled, OE = HIGH or LOW)
tWC
ADDRESS
tSCS1 tHA
CS1
tSCS2
CS2
tAW tPWE tSA tHZWE
HIGH-Z
WE
tLZWE
DOUT
DATA UNDEFINED
tSD
tHD
DIN
DATA-IN VALID
8
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
IS62WV10248BLL
ISSI
tWC
(R)
WRITE CYCLE NO. 2 (WE Controlled: OE is HIGH During Write Cycle)
ADDRESS
OE
tSCS1 tHA
CS1
tSCS2
CS2
tAW tPWE tSA tHZWE
HIGH-Z
WE
tLZWE
DOUT
DATA UNDEFINED
tSD
tHD
DIN
DATA-IN VALID
WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle)
tWC
ADDRESS
OE
tSCS1 tHA
CS1
tSCS2
CS2
tAW tPWE tSA tHZWE
HIGH-Z
WE
tLZWE
DOUT
DATA UNDEFINED
tSD
tHD
DIN
DATA-IN VALID
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
9
IS62WV10248BLL
ISSI
Test Condition See Data Retention Waveform VDD = 1.2V, CS1 VDD - 0.2V See Data Retention Waveform See Data Retention Waveform Min. 1.2 -- 0 tRC Max. 3.6 20 -- -- Unit V A ns ns
(R)
DATA RETENTION SWITCHING CHARACTERISTICS
Symbol VDR IDR tSDR tRDR Parameter VDD for Data Retention Data Retention Current Data Retention Setup Time Recovery Time
DATA RETENTION WAVEFORM (CS1 Controlled) CS1
tSDR VDD 3.0V Data Retention Mode tRDR
2.2V
VDR CS1 VDD
CS1 GND
- 0.2V
DATA RETENTION WAVEFORM (CS2 Controlled)
Data Retention Mode VDD 3.0 CS2 2.2V VDR 0.4V GND CS2 0.2V tSDR tRDR
10
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
IS62WV10248BLL
ISSI
(R)
ORDERING INFORMATION: IS62WV10248BLL (2.5V - 3.6V)
Industrial Range: -40C to +85C
Speed (ns) 55 70 70 Order Part No. IS62WV10248BLL-55BI IS62WV10248BLL-55BLI IS62WV10248BLL-70BI IS62WV10248BLL-70XI Package mini BGA (7.2mm x 8.7mm) mini BGA (7.2mm x 8.7mm), Lead-free mini BGA (7.2mm x 8.7mm) DIE
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06
11
IS62WV10248BLL Mini Ball Grid Array Package Code: B (48-pin)
Top View 1 2 3 4 56 6 Bottom View
b (48x)
ISSI
(R)
5
4
3
2
1
A B C D D E F G H D1
e
A B C D E F G H
e E E1
A2 SEATING PLANE A1
A
mBGA - 7.2mm x 8.7mm
MILLIMETERS Sym.
N0. Leads A A1 A2 D D1 E E1 e b 7.10 -- 0 .24 0.60 8.60
INCHES Min. Typ. Max.
Notes: 1. Controlling dimensions are in millimeters.
Min. Typ. Max.
48 -- -- -- 8.70 5.25BSC 7.20 7.30 3.75BSC 0.75BSC 0.30 0.35 0.40 1.20 0.30 -- 8.80
-- 0.009 0.024
-- -- --
0.047 0.012 --
0.339 0.343 0.346 0.207BSC 0.280 0.283 0.287 0.148BSC 0.030BSC 0.012 0.014 0.016
12
Integrated Silicon Solution, Inc. -- www.issi.com -- 1-800-379-4774
Rev. C 03/17/06


▲Up To Search▲   

 
Price & Availability of IS62WV10248BLL-70BI

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X