 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector General Description The ME70XXA series is a set of three-terminal low power voltage detectors implemented in CMOS technology. Each voltage detector in the series detects a particular fixed voltage ranging from 2.4V to 5V. The voltage detectors consist of a high-precision voltage divider circuit, band gap voltage source, a comparator and an output driver. CMOS technology ensures low power consumption. Although designed primarily as fixed voltage detectors, these devices can be used with external components to detect user specified threshold voltages (NMOS open drain type only). Features Low power consumption Low temperature coefficient Built-in high-stability reference source Built-in hysteresis characteristic TO-92 and SOT-23 package Applications Battery checkers Level selectors Power failure detectors Microcomputer reset Battery memory backup Non-volatile RAM signal storage protector Selection Table Part No. ME7027A ME7044A Detectable Voltage 2.7V 4.4V Hysteresis Width 0.13V 0.22V Tolerance 3% 3% Package TO-92 SOT-23 Marking 70XX (for TO-92) 0XX (for SOT-23) Note: The output type selection codes are: NMOS open drain normal open, active low For example: The ME7044A is a 4.4V, NMOS open drain active low output Output Type Selection Table Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector Block Diagram N Channel Open Drain Output (Normal Open; Active Low) A Type Pin Assignment Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector Absolute Maximum Ratings Supply Voltage ..........................VSS-0.3V to VSS+10V Output Voltage ........................VSS-0.3V to VDD+0.3V Storage Temperature ............................-50ae to 125ae Operating Temperature..............................0ae to 70ae Output Current...................................................50mA Power Consumption ........................................200mW Note: These are stress ratings only. Stresses exceeding the range specified under "Absolute Maximum Ratings" may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Electrical Characteristics ME7027A Symbol VDET VHYS IDD VDD IOL Parameter Detection Voltage Hysteresis Width Operating Current Operating Voltage Output Sink Current Test Conditions VDD Conditions Min. 2.619 0.02 VDET Typ. 2.700 0.05 VDET 2 Max. 2.781 0.1 VDET 3 10 Unit V V 8V No load 1.5 0.5 A V mA 2V VOUT=0.2V 1 VDET Ta ME7044A Symbol VDET VHYS IDD VDD IOL Temperature Coefficient 0ae mV/ae Parameter Detection Voltage Hysteresis Width Operating Current Operating Voltage Output Sink Current Test Conditions VDD Conditions Min. 4.268 0.02 VDET Typ. 4.400 0.05 VDET 2 Max. 4.532 0.1 VDET 3 10 Unit V V 8V No load 1.5 3 A V mA 3.6V VOUT=0.2V 6 VDET Ta Temperature Coefficient 0 0.2 mV/ae Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector Functional Description The ME70XXA series is a set of voltage detectors equipped with a high stability voltage reference which is connected to the negative input of a comparatordenoted as VREF in the following figure for NMOS output voltage detector. When the voltage drop to the positive input of the comparator (i,e,VB) is higher than VREF, VOUT goes high, and VB is expressed as VBH=VDDxRB / (RA +RB). If VDD is decreased so that VB falls to a value less than VREF, the comparator output inverts from high to low, VOUT goes low, VC is high. If VDD falls below the minimum operating voltage, the output becomes undefined. The figure demonstrates the NMOS output type with positive output polarity (VOUT is normally open, active low). Application circuits shown are examples of positive output polarity (normally open, active low) unless otherwise specified. NMOS open drain output application with R-C delay Application Circuits Microcomputer Reset Circuit Normally a reset circuit is required to protect the microcomputer system from malfunctions due to power fail . The following examples show how different output configurations perform a reset function in various systems. NMOS open drain output application for separate power supply NMOS Output Voltage Detector (ME70XXA) Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector Power-on Reset Circuit With several external components, the NMOS open drain type of the ME70XXA series can be used to perform a power-on reset function as shown. 5V Power Line Monitoring Circuit Generally, a minimum operating voltage of 4.5V is guaranteed in a 5V power line system. The ME7044A is recommended for use as 5V power line monitoring circuit. 5V power line monitor with power-on reset Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector Package Information 3-Pin TO-92 Outline Dimensions Shanghai Union Microsystems, Inc www.union-ic.com Rev 0.0.1. SEP. 2003 ME70XXA Voltage Detector 3-Pin SOT-23 Outline Dimensions Shanghai Union Microsystems, Inc www.union-ic.com |
Price & Availability of ME7044A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |