Part Number Hot Search : 
85HF60R S10430 NJU7771F 00146 2SD0874 4HC25 RL4ZZ Z2SMB33
Product Description
Full Text Search
 

To Download IL2411 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 TECHNICAL DATA
Tone Ringer
The IL2411 is a bipolar integrated circuit designed for telephone bell replacement. * Designed for Telephone Bell Replacement * Low Current Drain * Adjustable 2-frequency Tone * Adjustable Warbling Rate * Extension Tone Ringer Modules * Alarms or Other Alerting Devices * Adjustable for Reduced Supply Initiation Current. * Built-in hysteresis prevents false triggering and rotary dial `Chirps'
IL2411N/D
8-SOP
8-DIP
TA = -45 to 65 C
LOGIC DIAGRAM PIN ASSIGNMENT
V CC R SL
OUT HFI HF0 GND
LFI LF0
1. 2. 3. 4.
PIN 1 = VCC PIN 5 = GND Output amplifier High frequency oscillator Low frequency oscillator Hysteresis regulator (Regulator circuit has built-in hysteresis to prevent false triggering and rotary dial "Chirps")
1
IL2411
PIN DESCRIPTION
Name VCC RSL LFI LF0 GND HF0 HFI Out Pin 1 2 3 4 5 6 7 8 Positive power supply. External resistor Input low frequency oscillator Output low frequency oscillator Negative power supply High frequency oscillator output High frequency oscillator input Tone output Description
MAXIMUM RATINGS*
Symbol VCC PD Parameter DC Supply Voltage (Referenced to GND) Power Dissipation in Still Air, Plastic DIP Value to +30.0 400 Unit V mW
Tstg
*
Storage Temperature
-65 to +150
C
Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC TA Parameter DC Supply Voltage (Referenced to GND) Operating Temperature Min 13.0 -45 Max 29.0 +65 Unit V C
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open.
2
IL2411
ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND, TA = -20 to +70C)
Guaranteed Limits Symbol VSI ISI VSUS ISUS VOH VOL IIN Parameter Initiation Supply Voltage (1) Initiation Supply Current (1) Sustaining Voltage (2) Sustaining Current (2) High-Level Output Voltage Low-Level Output Voltage Maximun Input Leakage Current (Pin 3) (Pin 7) fH1 fH2 fL High Frequency 1 High Frequency 2 Low Frequency See Figure 1 No Load VCC=VSUS See Figure 1 VCC=21V, IOH=-15mA, Pin 6=6V, Pin 7=GND VCC=21V, IOL=15mA, Pin 6=GND, Pin 7=6V Pin 3=6V,Pin 4=GND, VCC=21V Pin 7=6V,Pin 6=GND, VCC=21V R3=191K,C3=6800pF R3=191K,C3=6800pF R2=165K,C2=0.47F Test Conditions See Figure 1 Min 16.8 1.4 9.5 0.7 16.7 461 576 9.0 Typ Max 21.2 4.2 12.2 2.5 21.0 1.8 1.0 1.0 563 704 11.0 Unit V mA V mA V V A A Hz Hz Hz
Notes: 1. Initiation supply voltage (VSI) is the supply voltage required to start the tone ringer oscillating. 2. Sustaining voltage (VSUS) is the supply voltage required to maintain oscillation.
3
IL2411
CIRCUIT CURRENT-SUPPLY VOLTAGE (NO LOAD)
Figure 1 SUPPLY CURRENT (NO LOAD) VC. SUPPLY VOLTAGE
Figure 2
4
IL2411
APPLICATION CIRCUIT
F igure 3
APPLICATION NOTE
The application circuit illustrates the use of the IL2411 devices in typical telephone or extension tone ringer application. The AC ringer signal voltage appears across the TIP and RING inputs of the circuit and is attenuated by capacitor C1 and resistor R1. C1 also provides isolation from DC voltages (48V) on the exchange line. After full wave rectification by the bridge diode, the waveform is filtered by capacitor C4 to provide a DC supply for the tone ringer chip. As this voltage exceeds the initiation voltage (VSI), oscillation starts. With the components shown, the ouptut frequency chops between 512(fh1) and 640Hz(fh2) at a 10Hz(fL) rate. The loudspeaker load is coupled through a 1300 to 8 transformer. The output coupling capacitor C5 is required with transformer coupled loads. When driving a piezo-ceramic transducer type load, the coupling C5 and transformer (1300:8) are not required. However, a current limiting resistor is required. The low frequency oscillator oscillates at a rate (fL) controlled by an external resistor (R2) and capacitor (C2). The frequency can be determined using the relation fL=1/1.289R2*C2. The high frequency oscillates at a fH1, fH2 controlled by an external resistor (R3) and capacitor (C3). The frequency can be determined using the relation fH1=1/1.504R3*C3, fH2=1/1.203R3*C3. Pin 2 allows connection of an external resistor RSL, which is used to program the solpe of the supply current vs supply voltage characteristics (see Fig2), and hence the supply current up to the initiation voltage ( VSI ). This initiation voltage remains constant independent of RSL. The supply current drawn prior to triggering varies inversely with RSL, decreasing for increasing value of resistance. Thus, increasing the value of RSL will decrease the amount of AC ringing current required to trigger the device. As such, longer sucribser loops are possible since less voltage is dropped per unit length of loop wire due to the lower current level. RSL can also be used to compensated for smaller AC couplin capacitors (C5 on Fig 3) (higher impedance) to the line which can be used to alter the ringer equivalence number of a tone ringer circuit. The graph in Fig2 illustrates the variation of supply current with supply voltage. Three curves are drawn to show the variation of initiation current with RSL. Curve B( RSL=6.8K) shows the I-V characteristic for the IL2411 tone ringer. Curve A is a plot with RSL<6.8K and shows an increase in the current drawn up to the initiation voltageVSI. The I-V characteristic after initiation remains unchanged. Curve C illustrates the effect of increasing RSL above 6.8K initiation current decreases but again current after triggering is unchanged.
5
IL2411
N SUFFIX PLASTIC DIP (MS - 001BA)
A 8 5 B 1 4
Dimension, mm Symbol A B MIN 8.51 6.1 MAX 10.16 7.11 5.33 0.36 1.14 2.54 7.62 0 2.92 7.62 0.2 0.38 10 3.81 8.26 0.36 0.56 1.78
F
L
C D
C -T- SEATING
PLANE
F G
M H J
N G D 0.25 (0.010) M T K
H J K L M N
NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side.
D SUFFIX SOIC (MS - 012AA) Dimension, mm
5
A 8
Symbol A
B P
MIN 4.8 3.8 1.35 0.33 0.4 1.27 5.72 0 0.1 0.19 5.8 0.25
MAX 5 4 1.75 0.51 1.27
H
B C
1
G
4 C R x 45
D F
-TD 0.25 (0.010) M T C M K
SEATING PLANE
G
J F M
H J K M P R
8 0.25 0.25 6.2 0.5
NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B 0.25 mm (0.010) per side.
6


▲Up To Search▲   

 
Price & Availability of IL2411

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X