|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
INTEGRATED CIRCUITS DATA SHEET UMA1016xT Frequency synthesizer for radio communication equipment Product specification Supersedes data of June 1992 File under Integrated Circuits, IC03 1995 Jul 12 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment FEATURES * RF input frequencies to 1 GHz * Fully programmable RF divider * 3-wire serial bus interface * On-chip 3 to 16 MHz crystal oscillator * Mask programmable /2 to /31 reference divider ratio * Up to 1 MHz channel spacing * Crystal frequency buffered output * Dual register architecture for fast Tx/Rx switching in TDD single synthesizer systems * Phase detector compensated for supply and temperature variations * Power-down mode. APPLICATIONS * 900 MHz cordless telephones * Portable battery-powered radio equipment. GENERAL DESCRIPTION UMA1016xT The UMA1016xT is a low power synthesizer for radio communications. Manufactured in bipolar technology, it is designed for a 70 to 1000 kHz channel spacing in the 500 to 1000 MHz band. The channel is programmed via a 3-wire serial bus. The internal dual register architecture allows a single synthesizer to be used in TDD systems. Fast switching between transmit and receive frequencies is achieved without the need for bus overhead. It also incorporates a sensitive, low power RF divider and a dead-zone-eliminated 3-state phase comparator. A power-down mode enables the circuit to be idled. QUICK REFERENCE DATA SYMBOL Supply VCC VDD ICC + IDD IDD(pd) fref RFI Tamb supply voltage supply voltage supply current digital supply current in power-down phase comparator frequency RF input frequency operating ambient temperature Tamb = -10 to +70C Tamb = 0 to +70C 4.5 4.5 - - 70 500 500 -10 - - 12 0.8 250 - - - 5.5 5.5 - - 1000 800 1000 +70 V V mA mA kHz MHz MHz C PARAMETER CONDITIONS MIN. TYP. MAX. UNIT ORDERING INFORMATION TYPE NUMBER UMA1016AT(1) UMA1016BT(2) UMA1016xT(3) Notes 1. UMA1016AT has a Reference Division Factor of 27. 2. UMA1016AT has a Reference Division Factor of 16. 3. UMA1016xT is a customized version. 1995 Jul 12 2 PACKAGE NAME SO16 SO16 SO16 PIN POSITION plastic small outline package; 16 leads; body width 3.9 mm plastic small outline package; 16 leads; body width 3.9 mm plastic small outline package; 16 leads; body width 3.9 mm VERSION SOT109-1 SOT109-1 SOT109-1 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment BLOCK DIAGRAM UMA1016xT Tx/Rx handbook, full pagewidth 12 CK DATA 10 9 Ck REGISTER D Q REGISTER UMA1016XT INTERFACE EN 11 Tx LATCH Tx LATCH RFI 7 AMPLIFIER RF DIVIDER MAIN DIVIDER HPDN VDD DGND 5 3 BIAS GENERATORS Rx LATCH Rx LATCH 6 BUFFER OSCILLATOR DIVIDER 2 - 31 . . PHASE DETECTOR 15 V 14 CC AGND 16 CP 4 MGA193 - 1 1 RO1 2 RO2 REFCK Fig.1 Block diagram. 1995 Jul 12 3 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment PINNING SYMBOL RO1 RO2 VDD REFCK HPDN DGND RFI i.c. DATA CK EN TX/RX i.c. AGND VCC CP PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DESCRIPTION crystal oscillator input or TCXO input oscillator output to crystal circuit 5 V supply to digital section reference crystal frequency buffered output Hardware Power-Down Not; IC operates when pin is HIGH digital ground 1 GHz RF signal input internally connected programming bus data input programming bus clock input programming bus enable input (active LOW) transmit (HIGH)/receive (LOW) mode select input internally connected analog ground 5 V supply to charge pump circuit charge pump output handbook, halfpage UMA1016xT RO1 1 RO2 VDD REFCK HPDN DGND RFI i.c. 2 3 4 UMA1016XT 5 6 7 8 MGA192 - 1 16 CP 15 VCC 14 AGND 13 i.c. 12 TX/RX 11 EN 10 CK 9 DATA Fig.2 Pin configuration. FUNCTIONAL DESCRIPTION General The UMA1016xT is a low power synthesizer for radio communications in the range 500 to 1000 MHz. It includes an oscillator circuit, reference divider, RF divider, 3-state phase and frequency comparator, charge pump and main control circuit for the transfer of serial data into two internal registers. VDD supplies power to the digital circuits while VCC powers the charge pump. VDD and VCC are nominally 5 V but will operate in the range 4.5 V to 5.5 V. Reduced noise coupling is facilitated by separate digital and analog ground pins which must always be externally connected to the same DC potential to prevent the flow of large currents across the die. The synthesizer is placed in idle mode during power-down but the oscillator and buffer remain operative and may be used as a clock for system timing. Main divider The main divider is a fully programmable pulse-swallow type. Following a sensitive (50 mV, -13 dBm) input amplifier, the RF signal is applied to a 13-bit divider (MD13 to MD1). The division ratio is provided via the serial bus to two 13-bit latches, corresponding to transmit and receive frequencies. The serial programming register is written to under processor control, independently of divider operation. This removes difficulty if using a low data bus transmission speed. The new ratio is transferred to the appropriate latch when the programming enable signal (EN) returns HIGH. The last register bit (PB0) is used to determine whether the new value is loaded into the transmit (PB0 = 1) or receive (PB0 = 0) frequency latch. To avoid spurious phase changes, the divider incorporates the new ratio only at the end of the on-going reference period. The minimum division ratio is 512. One reference cycle is required to update a new ratio. Internal power-on occurs rapidly. 1995 Jul 12 4 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment Oscillator External capacitive feedback is applied to the common collector Colpitts oscillator which has high voltage supply rejection and negligible temperature drift. It is designed to function as an input buffer without the need for external components when a TCXO or other clock is used. A separate output buffer, which remains active during power-down (HPDN taken LOW), provides a TTL compatible signal to drive external logic circuits (REFCK). Reference divider The reference divider has a fixed divider ratio set by metal masking between 2 and 31. For example, a 4 MHz crystal connected to the oscillator and a /16 ratio allows a channel spacing of 250 kHz. Other frequencies and ratios are possible. Phase comparator The phase comparator combines a phase and frequency detector and charge pump (see Fig.3). The charge pump current is internally fixed and determined for fast switching. It is compensated against power supply and temperature variation. The detector is assembled from dual D-type flip-flops which, together with feedback, remove the `dead' zone. Upon the detection of a phase error, either UP or DO go HIGH. This gates the appropriate current generator to source or sink 1.75 mA at the output pin. When no phase error is detected, CP becomes 3-state. The tuning voltage of the VCO is established from the sum of the current pulses into the loop filter. A simple passive loop filter may be used to offer high performance without requiring an operational-amp. The phase comparator function is summarized in Table 2. Main control interface The programming control interface permits access to two internal latches, denoted Tx and Rx. The serial input bits on DATA, entered MSB first, are converted to a parallel word and stored in the appropriate latch under the control of the last entered register bit (PB0). When this is set UMA1016xT HIGH, data serially fed to the register is loaded into the transmit (Tx) latch; when PB0 is LOW, the data is transferred to the receive latch (Rx). The data sent to the synthesizer is loaded in bursts framed by the signal EN. Programming clock edges, together with their appropriate data bits, are ignored until EN becomes active (LOW). The internal latches are updated with the latest programming data when EN returns inactive (HIGH). Only the last 15 bits serially clocked into the device are retained within the programming register. One extra shift register bit (PB7) can be internally added via metal masking to allow direct software compatibility with a 7-bit swallow counter and a 64/65 dual-modulus prescaler. No check is made on the number of clock pulses received during the time that programming is enabled. EN going HIGH while CLOCK is still LOW generates an active clock edge causing a shift of the data bits. Data programmed into the register is lost during power-down (HPDN taken LOW). The maximum serial bus clock speed is specified as 5 MHz. Minimum speed is limited by the clock edge rise and fall times to ensure that no data transparency condition can exist. Independent of any serial programming activity, the RF divider chain uses the data previously stored within the selected latch to determine the synthesized channel frequency. The Tx/Rx signal controls which latch is read to preload the counter bits at each division cycle. When new data is updated into the device, it is used during the cycle following latch selection by the Tx/Rx control line. If the Tx/Rx line is tied LOW, only data loaded into the Rx latch is used. In this event the serial data stream clocked into the synthesizer must terminate with an `0'. The logic diagram for the first bits of the programming interface is shown in Fig.3. The other bits are processed in a similar manner by a further 9 stages of the shift register-latches-multiplexer. The signals supplied to the circuit are described by the timing diagram. The table of values has been specified for maximum bus speed. Under slow clocking conditions, rise and fall times must not be excessively slow. 1995 Jul 12 5 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment Table 1 Main divider division ratio MAIN COUNTER MD1 LSB Table 2 Operation of phase comparator SYMBOL UP DO Ipcd Table 3 FIRST pb14 md13 Note 1. pb7; see Section "Main control interface". pb13 pb12 pb11 md12 md11 md10 Fref < Fvar 0 1 -1.75 mA Fref > Fvar 1 0 +1.75 mA MD2 ../.. MD7 MD8 ../.. UMA1016xT MD12 MD13 MSB Fref = Fvar 0 0 <5 nA Register and latch bit allocations REGISTER AND LATCH BIT ALLOCATIONS pb10 md9 pb9 md8 pb8 md7 pb7(1) X pb6 md6 pb5 md5 pb4 md4 pb3 md3 pb2 md2 pb1 md1 LAST IN pb0 address VCC handbook, full pagewidth var UP PHASE AND FREQUENCY DETECTOR on/off 1.75 mA pump output on/off 1.75 mA ref DO AGND MGA194 Fig.3 Phase comparator block diagram. 1995 Jul 12 6 Fig.4 Simplified interface logic diagram. handbook, full pagewidth 1995 Jul 12 DATA D Philips Semiconductors Frequency synthesizer for radio communication equipment programming shift register Q D Q D Q D Q D Q DATA out FLIPFLOP CK FLIPFLOP CK FLIPFLOP CK FLIPFLOP CK FLIPFLOP CK Shift CK CK PB0 D Q D Q D Q D Q LATCH transmit frequency latch LATCH EN LATCH EN LATCH EN EN Tx Ld EN D Q FLIPFLOP CK D Q D Q D Q D Q receive frequency latch 7 LATCH EN End_Count_CK Rx Ld LATCH EN LATCH EN LATCH EN Not_End_Count MUX R OUT SEL Tx / Rx D Q MGA195 MUX R OUT B SEL B MUX R OUT SEL B MUX R OUT SEL B coefficient select multiplexer Select LATCH EN Bit 0 Bit 1 Bit 2 Bit 3 main divider coefficient UMA1016xT Product specification Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment UMA1016xT handbook, full pagewidth t su t h1 t cyc tf tr t end t new CK DATA msb lsb ladrs next EN t start t wid MGA196 Fig.5 Logic interface signals. 1995 Jul 12 8 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VDD VCC Vi Tstg Tamb HANDLING PARAMETER digital supply voltage range analog supply voltage range input voltage range storage temperature range operating ambient temperature to ground CONDITIONS MIN. -0.2 -0.2 0 -55 -10 UMA1016xT TYP. - - - - - MAX. UNIT 7 7 VDD 125 70 V V V C C Inputs and outputs are protected against electrostatic discharges in normal handling. However, to be totally safe, it is desirable to take normal precautions appropriate to handling integrated circuits. TIMING CHARACTERISTICS VDD and VCC = 5 V; Tamb = -10 to +70 C; unless otherwise specified; typical values measured at VCC and VDD = 5 V; Tamb = 25 C; note 1. SYMBOL Serial programming clock (pin 10) fck tr tf Tcy tstart tend twidth tnew tsu th1 Note 1. Minimum and maximum values are for maximum clock speed. clock frequency rise time fall time clock period 200 0.01 - 4 5 5 - - - - - - - 5 50 50 - - - - - - - MHz ns ns ns PARAMETER MIN. TYP. MAX. UNIT Enable programming (pin 11) delay to rising clock edge delay from last clock edge minimum inactive pulse width delay from EN inactive to new data 30 0 200 300 ns ns ns ns Register serial input data (pin 9) input data to CK set-up time input data to CK hold time 10 10 ns ns 1995 Jul 12 9 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment CHARACTERISTICS VDD and VCC = 5 V; Tamb = 25 C; unless otherwise specified. SYMBOL Power supply VDD VCC IDD ICC IDD(pd) fvco Vrf(rms) RiRF CiRF N digital voltage supply analog voltage supply digital supply current analog supply current digital supply current in power-down mode Tamb = -10 to +70C Tamb = 0 to +70C input signal voltage level (RMS value) input resistance input capacitance main divider division ratio RF = 1 GHz indicative; not tested VCC = 5.5 V; pump off VCC = VDD 4.5 4.5 VDD = 5.5 V; REFCK off - - - 5 5 10.1 1.9 0.8 - - - 350 1.5 - - - 5 2 5 PARAMETER CONDITIONS MIN. UMA1016xT TYP. MAX. UNIT 5.5 5.5 10.8 2.1 1.5 V V mA mA mA RF divider input (RFI) RF frequency range 500 500 50 - - 512 800 1000 200 - - 8191 MHz MHz mV pF Oscillator and reference divider (RO1, RO2) fref Vosc(rms) Co1 Zo2 Co2 fcp Icp(source) Icp(sink) Icp(leak) Vcp oscillator frequency range sinusoidal input level at pin 1 (RMS value) parasitic capacitance at pin 1 output impedance at pin 2 output capacitance indicative; not tested indicative; not tested indicative; not tested Rref(ck) used 3 0.1 - - - 16 0.5 - - - MHz V pF k pF Phase comparator and charge pump output (CP) phase detector frequency range charge pump source current charge pump sink current charge pump off leakage current charge pump voltage compliance range Icp within specified range VCC = 4.5 to 5.5 V VCC = 4.5 to 5.5 V 70 -2.2 1.3 -10 0.5 250 1.75 - - 1000 2.2 +10 kHz mA mA nA -1.75 -1.3 VCC - 0.5 V 1995 Jul 12 10 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment SYMBOL PARAMETER CONDITIONS MIN. UMA1016xT TYP. - - - - - 3 MAX. UNIT Interface logic input signal levels (HPDN, EN, DATA, CK, Tx/Rx) VIH VIL(PD) VIL Ibias Ci Voh Vol Io(sink) tr tf HIGH level input voltage LOW level input voltage LOW level input voltage input bias current input capacitance all inputs HPDN except HPDN logic 1 logic 0 indicative; not tested Oscillator buffered logic output signal (REFCK) HIGH level driven output voltage LOW level driven output voltage output sink current reference clock output rise time reference clock output fall time VCL = 0.5 V CI = 25 pF CL = 25 pF VDD = 5 V 3.5 0 -0.4 - - 4.0 - - 50 50 VDD - 0.5 V 0.4 - - - V mA ns ns 3 -0.3 -0.3 - -5 - VDD + 0.3 V 0.6 1 5 - - V V A A pF 1995 Jul 12 11 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment APPLICATION INFORMATION In a typical single-synthesizer application, the circuit is connected as shown in Fig.6. Both analog and digital supplies are decoupled to ground with HF and LF filter capacitors. Correct oscillator operation requires capacitors both to ground and to provide feedback across the amplifier. Five signals are shown fed from a microcontroller to provide serial programming, control TDD frequency selection and initiate the power-down mode. Other system logic may also be clocked by a crystal frequency output from the synthesizer. UMA1016xT A passive 2nd-order loop filter giving a 3rd-order system response is shown in Fig.6. Indicated values are intended for rapid frequency switching (500 s), 200 kHz channel spacing (reference /27) and breakthrough levels below -60 dB. The VCO output shows a power splitter supplying both the synthesizer RF input and drive buffer for other system components (RF amplifier in transmit mode, input mixer in receive mode). The minimizing of loop filter node leakage currents requires careful board layout. handbook, full pagewidth VP 220 pF 68 pF 33 pF 5.4 MHz 33 1 VP 2 3 REFCK 47 F 4 10 nF 5 6 7 1 nF 8 16 15 14 13 10 nF 47 F UMA1016XT 12 11 10 9 P4 P3 P2 P1 100 P0 82 12 VCO 18 k RFout 12 330 pF 4.7 nF MGA197 - 2 Fig.6 Application diagram. 1995 Jul 12 12 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment PACKAGE OUTLINES SO16: plastic small outline package; 16 leads; body width 3.9 mm UMA1016xT SOT109-1 D E A X c y HE vMA Z 16 9 Q A2 A1 pin 1 index Lp 1 e bp 8 wM L detail X (A 3) A 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3 0.010 0.057 0.069 0.004 0.049 0.019 0.0100 0.39 0.014 0.0075 0.38 0.244 0.050 0.041 0.228 0.028 0.004 0.012 8 0o o Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07S JEDEC MS-012AC EIAJ EUROPEAN PROJECTION ISSUE DATE 95-01-23 97-05-22 1995 Jul 12 13 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment SOLDERING SO or SSOP Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these cases reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Reflow soldering Reflow soldering techniques are suitable for all SO and SSOP packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. Wave soldering SO Wave soldering techniques can be used for all SO packages if the following conditions are observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The longitudinal axis of the package footprint must be parallel to the solder flow. * The package footprint must incorporate solder thieves at the downstream end. SSOP UMA1016xT Wave soldering is not recommended for SSOP packages. This is because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices. If wave soldering cannot be avoided, the following conditions must be observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The longitudinal axis of the package footprint must be parallel to the solder flow and must incorporate solder thieves at the downstream end. Even with these conditions, only consider wave soldering SSOP packages that have a body width of 4.4 mm, that is SSOP16 (SOT369-1) or SSOP20 (SOT266-1). METHOD (SO OR SSOP) During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Repairing soldered joints Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds at 270 to 320 C. 1995 Jul 12 14 Philips Semiconductors Product specification Frequency synthesizer for radio communication equipment DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Application information Where application information is given, it is advisory and does not form part of the specification. Limiting values UMA1016xT This data sheet contains target or goal specifications for product development This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1995 Jul 12 15 Philips Semiconductors - a worldwide company Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428) BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367 Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. (02)805 4455, Fax. (02)805 4466 Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213, Tel. (01)60 101-1236, Fax. (01)60 101-1211 Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands, Tel. (31)40 783 749, Fax. (31)40 788 399 Brazil: Rua do Rocio 220 - 5th floor, Suite 51, CEP: 04552-903-SAO PAULO-SP, Brazil. P.O. Box 7383 (01064-970), Tel. (011)821-2333, Fax. (011)829-1849 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS: Tel. (800) 234-7381, Fax. (708) 296-8556 Chile: Av. Santa Maria 0760, SANTIAGO, Tel. (02)773 816, Fax. (02)777 6730 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. (852)2319 7888, Fax. (852)2319 7700 Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17, 77621 BOGOTA, Tel. (571)249 7624/(571)217 4609, Fax. (571)217 4549 Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. (032)88 2636, Fax. (031)57 1949 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. (358)0-615 800, Fax. (358)0-61580 920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. (01)4099 6161, Fax. (01)4099 6427 Germany: P.O. Box 10 63 23, 20043 HAMBURG, Tel. (040)3296-0, Fax. (040)3296 213. Greece: No. 15, 25th March Street, GR 17778 TAVROS, Tel. (01)4894 339/4894 911, Fax. (01)4814 240 India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, Bombay 400 018 Tel. (022)4938 541, Fax. (022)4938 722 Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4, P.O. Box 4252, JAKARTA 12950, Tel. (021)5201 122, Fax. (021)5205 189 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. (01)7640 000, Fax. (01)7640 200 Italy: PHILIPS SEMICONDUCTORS S.r.l., Piazza IV Novembre 3, 20124 MILANO, Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2 -chome, Minato-ku, TOKYO 108, Tel. (03)3740 5130, Fax. (03)3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. (02)709-1412, Fax. (02)709-1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905, Tel. 9-5(800)234-7381, Fax. (708)296-8556 Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. (040)783749, Fax. (040)788399 (From 10-10-1995: Tel. (040)2783749, Fax. (040)2788399) New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. (09)849-4160, Fax. (09)849-7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. (022)74 8000, Fax. (022)74 8341 Pakistan: Philips Electrical Industries of Pakistan Ltd., Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton, KARACHI 75600, Tel. (021)587 4641-49, Fax. (021)577035/5874546 Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc, 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474 Portugal: PHILIPS PORTUGUESA, S.A., Rua dr. Antonio Loureiro Borges 5, Arquiparque - Miraflores, Apartado 300, 2795 LINDA-A-VELHA, Tel. (01)4163160/4163333, Fax. (01)4163174/4163366 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. (65)350 2000, Fax. (65)251 6500 South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430, Johannesburg 2000, Tel. (011)470-5911, Fax. (011)470-5494. Spain: Balmes 22, 08007 BARCELONA, Tel. (03)301 6312, Fax. (03)301 42 43 Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM, Tel. (0)8-632 2000, Fax. (0)8-632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. (01)488 2211, Fax. (01)481 77 30 Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978, TAIPEI 100, Tel. (02)388 7666, Fax. (02)382 4382 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, Bangkok 10260, THAILAND, Tel. (662)398-0141, Fax. (662)398-3319 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. (0 212)279 27 70, Fax. (0212)282 67 07 United Kingdom: Philips Semiconductors LTD., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. (0181)730-5000, Fax. (0181)754-8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556 Uruguay: Coronel Mora 433, MONTEVIDEO, Tel. (02)70-4044, Fax. (02)92 0601 Internet: http://www.semiconductors.philips.com/ps/ For all other countries apply to: Philips Semiconductors, International Marketing and Sales, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Telex 35000 phtcnl, Fax. +31-40-724825 (from 10-10-1995: +31-40-2724825) SCD41 (c) Philips Electronics N.V. 1995 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 413061/1500/03/pp16 Document order number: Date of release: 1995 Jul 12 9397 750 00206 |
Price & Availability of UMA1016AT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |