View HFA08SD60S_365104.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Bulletin PD-20618 rev. B 07/02
HFA08SD60S
Ultrafast, Soft Recovery Diode
Features
* * * * * * Ultrafast Recovery Time Ultrasoft Recovery Very Low IRRM Very Low Qrr Guaranteed Avalanche Specified at Operating Temperature
t rr = 18ns IF(AV) = 8Amp VR = 600V
Benefits
* Reduced RFI and EMI * Reduced Power Loss in Diode and Switching Transistor * Higher Frequency Operation * Reduced Snubbing * Reduced Parts Count
Description/ Applications
These diodes are optimized to reduce losses and EMI/RFI in high frequency power conditioning systems. The softness of the recovery eliminates the need for a snubber in most applications. These devices are ideally suited for freewheeling, flyback, power converters, motor drives, and other applications where high speed and reduced switching losses are design requirements.
Package Outline
D - PAK Absolute Maximum Ratings Parameters
VRRM IF(AV) IFSM IFRM PD TJ, TSTG Cathode-to-Anode Voltage Continuous Forward Current TC = 100C Single Pulse Forward Current Peak Repetitive Forward Current Maximum Power Dissipation TC = 100C Operating Junction and Storage Temperatures - 55 to 150 C 60 24 14 W
Max
600 8
Units
V A
www.irf.com
1
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
Electrical Characteristics @ TJ = 25C (unless otherwise specified)
Parameters
VBR, Vr VF Breakdown Voltage, Blocking Voltage Forward Voltage See Fig. 1
Min Typ Max Units Test Conditions
600 1.4 1.7 1.4 0.3 100 10 8.0 1.7 2.1 1.7 5.0 500 25 V V V V A A pF nH IR = 100A IF = 8A IF = 16A IF = 8A, TJ = 125C VR = VR Rated TJ = 125C, VR = 0.8 x VR Rated VR = 200V Measured lead to lead 5mm from package body
IR
Max. Reverse Leakage Current
-
CT LS
Junction Capacitance Series Inductance
-
Dynamic Recovery Characteristics @ TJ = 25C (unless otherwise specified)
Parameters
trr Reverse Recovery Time
Min Typ Max Units Test Conditions
-
18
37 55 3.5 4.5 65 124 240 210
55 90 5.0 8.0 138 360 -
ns
IF = 1.0A, diF/dt = 200A/A, VR = 30V TJ = 25C TJ = 125C IF = 8A VR = 200V diF /dt = 200A/s
IRRM
Peak Recovery Current
-
A
TJ = 25C TJ = 125C
Qrr
Reverse Recovery Charge
-
nC
TJ = 25C TJ = 125C
di(rec)M/dt Rate of Fall of recovery Current
-
A/s
TJ = 25C TJ = 125C
Thermal - Mechanical Characteristics
Parameters
TJ TStg Tlead RthJC RthJA ! Wt Max. Junction Temperature Range Max. Storage Temperature Range Lead Temperature Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient Weight
Min
-
Typ
2.0 0.07
Max
- 55 to 150 - 55 to 150 300 3.5 80 -
Units
C
C/ W
g (oz)
!
Typical Socket Mount
2
www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
00
1000 100
T J = 150C 125C
Reverse Current - I R (A)
10 1
25C
0.1 0.01 0.001
0 100 200 300 400 500 600
Reverse Voltage - VR (V) Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage
Instantaneous Forward Current - I
F
(A)
10
100
1
T = 150C J T = 125C J T = 25C J
Junction Capacitance - C T (pF)
T J = 25C
10
0.1 0.4 0.8 1.2 1.6
1
2 2.4 2.8 3.2 3.6 4
1
10
100
1000
Forward Voltage Drop - V FM (V) Fig. 1 - Typical Forward Voltage Drop Characteristics
Reverse Voltage - V R (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage
10
(C/W)
Thermal Impedance Z
1
D = 0.50 D = 0.20 D = 0.10 D = 0.05 D = 0.02 D = 0.01 Single Pulse (Thermal Resistance)
thJC
PDM
t1 t2
0.1
Notes: 1. Duty factor D = t1/ t2 2. Peak Tj = Pdm x ZthJC + Tc
.01 0.00001
t1, Rectangular Pulse Duration (Seconds) Fig. 4 - Max. Thermal Impedance Z thJC Characteristics
0.0001
0.001
0.01
0.1
1
www.irf.com
3
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
80 70 60 50 40 30 20 10 100
diF /dt (A/ s) Fig. 5 - Typical Reverse Recovery vs. di F /dt
Vr = 200V Tj = 125C Tj = 25C
20
If = 16A If = 8A If = 4A
15
If = 16A If = 8A If = 4A
trr (ns)
Irr (A)
10
5
Vr = 200V Tj = 125C Tj = 25C
1000
0 100
1000
Average Forward Current - IF(AV) (A) Fig. 6 - Typical Recovery Current vs. di F /dt
500
Vr = 200V Tj = 125C Tj = 25C
10000
Vr = 200V Tj = 125C Tj = 25C
400
Qrr ( nC )
300
di (rec)M / dt (A/ s)
If = 16A If = 8A If = 4A
If = 16A If = 8A If = 4A
1000
200
100
0 100
di F /dt (A/s )
1000
100 100
di F /dt (A/s )
1000
Fig. 8 - Typical di (rec)M /dt vs. di F /dt
Fig. 7 - Typical Stored Charge vs. di F /dt
4
www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
Reverse Recovery Circuit
VR = 200V
0.01 L = 70H D.U.T.
di F /dt dif/dt ADJUST
D G IRFP250 S
Fig. 9- Reverse Recovery Parameter Test Circuit
3
IF 0
trr ta tb
4
2
Q rr I RRM
0.5 I RRM di(rec)M/dt 0.75 I RRM
5
1
/dt di fF/dt
1. diF/dt - Rate of change of current through zero crossing 2. IRRM - Peak reverse recovery current 3. trr - Reverse recovery time measured from zero crossing point of negative going IF to point where a line passing through 0.75 IRRM and 0.50 IRRM extrapolated to zero current
4. Qrr - Area under curve defined by t rr and IRRM t rr x I RRM Q rr = 2 5. di (rec)M /dt - Peak rate of change of current during t b portion of t rr
Fig. 10 - Reverse Recovery Waveform and Definitions
www.irf.com
5
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
Outline Table
2.38 (0.09) 6.73 (0.26) 6.35 (0.25) 5.46 (0.21) 5.21 (0.20)
4
2.19 (0.08) 1.27 (0.05) 0.88 (0.03)
1.14 (0.04) 0.89 (0.03) 0.58 (0.02) 0.46 (0.02)
MINIMUM RECOMMENDED FOOTPRINT 5.97 (0.24)
6.45 (0.24) 6.22 (0.24) 1.64 (0.02)
1 2 3
5.68 (0.22) 10.42 (0.41) 9.40 (0.37) 0.51 (0.02) MIN.
6.48 (0.26) 10.67 (0.42)
5.97 (0.23)
1.52 (0.06) 1.15 (0.04) 2x 1.14 (0.04) 0.76 (0.03) 2.28 (0.09) 2x 3x 0.89 (0.03) 0.64 (0.02) 1 - Anode 1 -- Cathode 2 Cathode 3 Anode 2 -- Cathode 4 - Cathode
2x 2.54 (0.10) 1.65 (0.06) 2x
Base Common Cathode
4
0.58 (0.02) 0.46 (0.02)
2.28 (0.09) 2x
4.57 (0.18)
3 - Anode 4 - Cathode
2
Conform to JEDEC outline D-Pak Dimensions in millimeters and (inches)
1
3
Cathode
Anode
Tape & Reel Information
TRR
1.60 (0.063) 1.50 (0.059)
4.10 (0.161) 3.90 (0.153) FEED DIR ECTION
1.60 (0.063) 1.50 (0.059)
DIA. 0.368 (0.0145) 0.342 (0.0135)
1.85 (0.073) 1.65 (0.065)
11.60 (0.457) 11.40 (0.449)
15.42 (0.609) 15.22 (0.601) 1.75 (0 .069)
24.30 (0.957) 23.90 (0.941)
TRL
10.90 (0.429) 10.70 (0.421)
1.25 (0 .049) 16.10 (0.634) 15.90 (0.626)
DIA.
4.72 (0.186) 4.52 (0.178)
FEED DIRECTION
13.50 (0.532) 12.80 (0.504) DIA.
26.40 (1.039) 24.40 (0.961)
SMD-220 Tape & Reel When ordering, indicate the part
360 (14.173) DIA. MAX.
60 (2.36 2) D IA. MIN .
number,SMD-220 Tape & Reel part orientation, and the quantity. Quantities are in multiples When ordering, indicate the part of 800 pieces per reel for both number, part orientation and the TRL and TRR.
quantity. Quantities are in multiples of 800 pieces per reel for both TRL and TRR.
6
www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. B 07/02
Marking Information
EXAMPLE: THIS IS AN HFA08SD60S
INTERNATIONAL RECTIFIER LOGO 2 (K) PART NUMBER
HFA08SD60S 9812 5K3A
ASSEMBLY LOT CODE 1 (K) 3 (A) DATE CODE (YYWW) YY = YEAR WW = WEEK
Ordering Information Table
Device Code
HF
1
A
2
08
3
SD
4
60
5
S
6
1 2 3 4 5 6
-
Hexfred Family Electron Irradiated Current Rating (08 = 8A) D-PAK Voltage Rating (60 = 600V) Suffix S = D2PAK/ Dpak
TR = Tape & Reel TRL = Tape & Reel Left TRR= Tape & Reel Right
Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 07/02
www.irf.com
7

▲Up To Search▲

Price & Availability of HFA08SD60S

	To Download HFA08SD60S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .