View BGM1014_355042.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BGM1014
MMIC wideband amplifier
Rev. 01 -- 11 March 2005 Product data sheet
1. Product profile
1.1 General description
Silicon Monolithic Microwave Integrated Circuit (MMIC) wideband amplifier with internal matching circuit in a 6-pin SOT363 SMD plastic package.
CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Therefore care should be taken during transport and handling.
MSC895
1.2 Features
s s s s s Internally matched to 50 Good output match to 75 32 dB to 34 dB positive sloped gain for Low Noise Block (LNB) application 12.9 dBm saturated load power at 1 GHz 40 dB isolation
1.3 Applications
s LNB Intermediate Frequency (IF) amplifiers s Cable systems s General purpose
1.4 Quick reference data
Table 1: Symbol VS IS |s21|2 NF PL(sat) Quick reference data Parameter DC supply voltage DC supply current insertion power gain noise figure saturated load power f = 1 GHz f = 1 GHz f = 1 GHz Conditions RF input; AC coupled Min 17 31.5 12.5 Typ 5 21.0 32.3 4.2 12.9 Max 6 25 33.0 4.3 Unit V mA dB dB dBm
Philips Semiconductors
BGM1014
MMIC wideband amplifier
2. Pinning information
Table 2: Pin 1 2, 5 3 4 6 Pinning Description VS GND2 RF_OUT GND1 RF_IN
1 2 3 6 4 2, 5
sym062
Simplified outline
6 5 4
Symbol
1
3
3. Ordering information
Table 3: Ordering information Package Name BGM1014 SC-88 Description plastic surface mounted package; 6 leads Version SOT363 Type number
4. Marking
Table 4: BGM1014 Marking Marking code C5Type number
5. Limiting values
Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VS IS Ptot Tstg Tj PD Parameter DC supply voltage supply current total power dissipation storage temperature junction temperature maximum drive power Tsp 90 C Conditions RF input; AC coupled Min -65 Max 6 30 200 +150 150 -10 Unit V mA mW C C dBm
6. Recommended operating conditions
Table 6: Symbol VS Tamb Operating conditions Parameter DC supply voltage ambient temperature Conditions Min 4.5 -40 Typ 5.0 +25 Max 5.5 +85 Unit V C
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
2 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
7. Thermal characteristics
Table 7: Symbol Rth(j-sp) Thermal characteristics Parameter thermal resistance from junction to solder point Conditions Ptot = 200 mW; Tsp 90 C Typ 300 Unit K/W
8. Characteristics
Table 8: Characteristics VS = 5 V; IS = 21.1 mA; Tj = 25 C; measured on demo board; unless otherwise specified. Symbol Parameter VS IS |s21|2 DC supply voltage supply current insertion power gain see Figure 4 f = 100 MHz f = 1 GHz f = 1.8 GHz f = 2.2 GHz f = 2.6 GHz f = 3 GHz |s11|2 |s22|2 input return loss output return loss f = 1 GHz f = 2.2 GHz ZL = 50 f = 1 GHz f = 2.2 GHz ZL = 75 f = 1 GHz f = 2.2 GHz |s12|2 isolation see Figure 3 f = 1 GHz f = 2.2 GHz NF noise figure see Figure 7 f = 1 GHz f = 2.2 GHz B K bandwidth stability factor 3 dB below flat gain at f = 1 GHz see Figure 8 f = 1 GHz f = 2.2 GHz PL(sat) PL(1dB) saturated load power load power at 1 dB gain compression f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz 1.5 0.9 12.5 8.8 10.5 5.0 1.6 1.0 12.9 9.3 11.2 5.7 dBm dBm dBm dBm 4.2 4.1 2.5 4.3 4.3 dB dB GHz 40 35 42 37 dB dB 12 12 16.8 17.7 dB dB 15 12 18.9 16.7 dB dB 29.0 31.5 34.0 33.0 29.0 25.0 11 7.5 30.0 32.3 35.2 34.1 30.5 26.4 12.2 8.8 31.0 33.0 36.5 35.5 32.0 28.0 dB dB dB dB dB dB dB dB Conditions RF input; AC coupled Min 17 Typ 5 21.0 Max 6 25 Unit V mA
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
3 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
Table 8: Characteristics ...continued VS = 5 V; IS = 21.1 mA; Tj = 25 C; measured on demo board; unless otherwise specified. Symbol Parameter IP3in IP3out IM2 input third order intercept point Conditions f = 1 GHz f = 2.2 GHz output third order intercept point f = 1 GHz f = 2.2 GHz second order intermodulation distortion f0 = 1 GHz; PL = -10 dBm f0 = 1 GHz; PL = -5 dBm Min -13 -21 19.5 14 36 33 Typ -11.8 -19 20.5 15.1 37 34 Max Unit dBm dBm dBm dBm dBc dBc
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 +0.2
100MHz
+5
0.4 0.2
180
0
0.2
0.5
1
3GHz
2
5
10
0
0
-0.2
-5
-135
-0.5 -1 -90
-2
-45 1.0
001aac489
IS = 21.1 mA; VS = 5 V; PD = -35 dBm; Zo = 50
Fig 1. Input reflection coefficient (s11); typical values
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
4 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 +0.2
100MHz
+5
0.4 0.2
180
0
0.2
0.5
3GHz
1
2
5
10
0
0
-0.2
-5
-135
-0.5 -1 -90
-2
-45 1.0
001aac490
IS = 21.1 mA; VS = 5 V; PD = -35 dBm; Zo = 50
Fig 2. Output reflection coefficient (s22); typical values
0 s12 2 (dB) -10
001aac491
50 s21 2 (dB) 40
001aac492
-20 30 -30 20
(1) (2) (3)
-40
-50 0 1000 2000 f (MHz) 3000
10 0 1000 2000 f (MHz) 3000
IS = 21.1 mA; VS = 5 V; PD = -35 dBm; Zo = 50
PD = -35 dBm; Zo = 50 (1) IS = 25.6 mA; VS = 5.5 V (2) IS = 21.5 mA; VS = 5 V (3) IS = 16.6 mA; VS = 4.5 V
Fig 3. Isolation (|s12 typical values
|2)
as a function of frequency;
Fig 4. Insertion gain (|s21|2) as a function of frequency; typical values
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
5 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
20 PL (dBm) 15
001aac493
15 PL (dBm) 5
(1) (2) (3)
001aac494
(1) (2) (3)
10
5 -5 0
-5 -40
-30
-20 PD (dBm)
-10
-15 -50
-40
-30
-20 -10 PD (dBm)
f = 1 GHz; Zo = 50 (1) VS = 5.5 V (2) VS = 5 V (3) VS = 4.5 V
f = 2.2 GHz; Zo = 50 (1) VS = 5.5 V (2) VS = 5 V (3) VS = 4.5 V
Fig 5. Load power as a function of drive power at 1 GHz; typical values
5 NF (dB) 4.5
(1) (2) (3)
Fig 6. Load power as a function of drive power at 2.2 GHz; typical values
5 K 4
001aac496
001aac495
3
2 4 1
3.5 0 500 1000 1500 2000 2500 f (MHz)
0 0 1000 2000 3000 f (MHz) 4000
Zo = 50 (1) VS = 5.5 V (2) VS = 5 V (3) VS = 4.5 V
IS = 21.1 mA; VS = 5 V; Zo = 50
Fig 7. Noise figure as a function of frequency; typical values
Fig 8. Stability factor as a function of frequency; typical values
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
6 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
9. Application information
Figure 9 shows a typical application circuit for the BGM1014 MMIC. The device is internally matched to 50 and therefore does not need any external matching. Good impedance matching is also achieved with a 75 load. The value of the input and output DC blocking capacitors C1 and C2 should be not more than 100 pF for applications above 100 MHz. Their values can be used to fine-tune the input and output impedance. For the RF choke, optimal results are obtained with a good quality chip inductor like the TDK MLG1608 (0603) or a wire-wound SMD. The value of the inductor can be used to fine-tune the output impedance. The RF choke and supply decoupling components should be located as close as possible to the MMIC. Ground paths must be as short as possible. The printed-circuit board (PCB) top ground plane must be as close as possible to the MMIC, and ideally directly beneath it. When using vias, use at least 3 vias for the top ground plane in order to limit ground path inductance. Supply decoupling with C3 should be from pin 1 to the same top ground plane.
VS 1 IN 6
C1 L1 C3 C2
VS
RF in
3 OUT
RF out
BGM1014
SOT363 4 2, 5
GND1
GND2
001aac488
Fig 9. Typical application circuit
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
7 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
Figure 10 shows the PCB layout used for the typical application.
30 mm
PH
30 mm IN OUT
V+
PH
IC1 C1 C2 L1 C3
IN
OUT
V+
001aab395
Material = FR4; thickness = 0.6 mm; r = 4.6
Fig 10. Printed-circuit board layout and component view for typical application Table 9: C1, C2 C3 L1 List of components used for the typical application Description multilayer ceramic chip capacitor multilayer ceramic chip capacitor SMD inductor Value 100 pF 22 nF 100 nH Dimensions 0603 0603 0603
Component
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
8 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
Table 10: Scattering parameters VS = 5 V; IS = 21.1 mA; PD = -35 dBm; Zo = 50 ; Tamb = 25 C; measured on demo board. f (MHz) 100 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 s11 Magnitude (ratio) 0.287 0.328 0.319 0.299 0.272 0.243 0.225 0.229 0.261 0.317 0.364 0.362 0.354 0.325 0.282 0.231 Angle (deg) 16.1 -3.9 -28.8 -50.3 -68.6 -84.7 -98.9 -106.9 -127.8 -154.4 167.7 126.7 87.5 47.6 7.7 -32.0 s21 Magnitude (ratio) 31.28 32.14 33.57 35.61 38.05 41.37 45.48 49.78 54.37 57.96 56.65 50.11 41.68 33.47 26.34 20.81 Angle (deg) 9.1 -7.1 -30.9 -52.3 -73.3 -95.5 -119.1 -144.8 -173.0 154.4 120.1 85.0 54.6 25.9 1.4 -20.3 s12 Magnitude (ratio) 0.02196 0.01734 0.01287 0.00969 0.00808 0.00751 0.00711 0.00792 0.00991 0.01171 0.01302 0.01493 0.01647 0.01878 0.02094 0.02184 Angle (deg) 9.4 -3.3 -21.1 -35.3 -42.7 -44.8 -43.7 -37.3 -37.9 -37.2 -45.7 -60.5 -69.8 -81.7 -94.0 -112.2 s22 Magnitude (ratio) 0.355 0.258 0.208 0.179 0.149 0.113 0.084 0.042 0.042 0.059 0.123 0.130 0.130 0.137 0.135 0.112 Angle (deg) 125.5 115.3 87.6 62.1 34.7 10.3 -8.1 -4.5 34.4 41.5 15.9 -4.6 -32.5 -57.1 -74.9 -104.3 1.0 1.1 1.2 1.5 1.6 1.6 1.6 1.4 1.1 1.0 1.0 1.0 1.0 1.0 1.1 1.2 K-factor
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
9 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
10. Package outline
Plastic surface mounted package; 6 leads SOT363
D
B
E
A
X
y
HE
vMA
6
5
4
Q
pin 1 index
A
A1
1
e1 e
2
bp
3
wM B detail X Lp
c
0
1 scale
2 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1
OUTLINE VERSION SOT363
REFERENCES IEC JEDEC JEITA SC-88
EUROPEAN PROJECTION
ISSUE DATE 97-02-28 04-11-08
Fig 11. Package outline SOT363 (SC-88)
9397 750 14499 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
10 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
11. Revision history
Table 11: Revision history Release date 20050311 Data sheet status product data sheet Change notice Doc. number 9370 750 14499 Supersedes Document ID BGM1014_1
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
11 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
12. Data sheet status
Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
13. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
14. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
15. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
9397 750 14499
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 -- 11 March 2005
12 of 13
Philips Semiconductors
BGM1014
MMIC wideband amplifier
16. Contents
1 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description. . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data. . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Recommended operating conditions. . . . . . . . 2 Thermal characteristics. . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application information. . . . . . . . . . . . . . . . . . . 7 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 12 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Contact information . . . . . . . . . . . . . . . . . . . . 12
(c) Koninklijke Philips Electronics N.V. 2005
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 11 March 2005 Document number: 9397 750 14499
Published in The Netherlands

▲Up To Search▲

Price & Availability of BGM1014

	To Download BGM1014 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .