View MN15G1601_318778.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MN15G1601
Type ROM (x8-bit) x RAM (x4-bit) x Package Number of Instructions Minimum Instruction Execution Time
MN15G1601 16 K 512 LQFP064-P-1414 *Pb free 103 0.5 s at 1/4 frequency dividing (at 3.0 V to 5.5 V, 8 MHz) 1.0 s at 1/4 frequency dividing (at 2.4 V to 5.5 V, 4 MHz) 2.0 s at 1/8 frequency dividing (at 2.0 V to 5.5 V, 4 MHz)* * The lower limit for operation guarantee for EPROM built-in type is 2.3 V. * RESET * IRQ1 * IRQ2 * IRQ3 Timer counter 0 : 8-bit x 1 (event count, pulse output, simple pulse width meausurement, PWM output, remote control carrier output) Clock source ********************* 1/2, 1/8, 1/32, 1/128 of system clock frequency; 1/1, 1/4, 1/16, 1/64 of XI(OSC) oscillation clock frequency Timer counter 1 : 8-bit x 1 (event count, pulse output, remote control carrier output) Clock source ********************* 1/2 of system clock frequency; 1/1, 1/214 of OSC oscillation clock frequency; 1/1, 1/26 of XI oscillation clock frequency Possible 16-bit cascade connection with timer counter 0 Timer counter 2 : 8-bit x 1 (event count, pulse output, simple pulse width meausurement, PWM output, remote control carrier output, one-shot timer output, trigger start PWM output, trigger start timer output) Clock source ********************* 1/2 of system clock frequency; 1/1, 1/2 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; TCI input Timer counter 3 : 8-bit x 1 (event count, pulse output, remote control carrier output, high-functional PWM output) Clock source ********************* 1/2 of system clock frequency; 1/1, 1/2 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; TCI input Possible 16-bit cascade connection with timer counter 2 Watchdog timer
Interrupts Timer Counter
Serial Interface I/O Pins A/D Inputs LCD Zero-Cross Inputs Special Ports I/O
Serial : 8-bit x 1 (synchronous type) Clock source ********************* 1/1, 1/2 of system clock frequency; SBT pin input 35 * Common use : 31 * Specified pull-up resistor available : 27 (software programmable) * Specified output architecture available : Nch open drain / push-pull : 31 (software programmable)
10-bit x 8-ch. (with S/H) 30 segments x 4 commons (1/2 , 1/3 , 1/4 duty) 1 Buzzer output (1 kHz, 2 kHz, 4 kHz : fosc = at 4 MHz)
212
MAC00001BEM
MN15G1601
Electrical Characteristics
Supply current
Limit Parameter Symbol IDD1 Operating supply current IDD2 IDD3 Supply current at HALT IDD4 IDD5 IDD6 Supply current at STOP IDD7 IDD8 IDD9 Condition min fosc = 8 MHz (1/8 dividing) fosc = 4 MHz (1/8 dividing) fosc = 32.768 kHz (1/8 dividing) fosc = 4 MHz (1/8 dividing) fosc = 32.768 kHz (1/8 dividing) ACZ = 1/2 VDD, Ta = 25C ACZ = 1/2 VDD, Ta = -40C to +85C Ta = 25C Ta = -40C to +85C typ 1.8 1.2 9.0 0.3 1.5 4.0 max 3.5 2.5 20 0.6 8.0 10 30 1.0 5.0 mA mA A mA A A A A A Unit
(Ta = -40C to +85C, VDD = 5.0 V, VSS = 0 V)
Pin Assignment
PB3/SEG15 PB2/SEG14 PB1/SEG13 PB0/SEG12 PA3/SEG11 PA2/SEG10 PA1/SEG9 PA0/SEG8 P93/SEG7 P92/SEG6 P91/SEG5 P90/SEG4 P83/SEG3 P82/SEG2 P81/SEG1 P80/SEG0 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 COM0 COM1 COM2 COM3 SEG22/AD0 SEG23/AD1 SEG24/AD2 SEG25/AD3 SEG26/AD4 SEG27/AD5
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
MN15G1601 MN15G1601
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
P62/TCO P61/START P60/NIRQ P33/key7 P32/BZ/key6 P31/NTCI/key5 P30/ACZ/key4 P23/SBT/key3 P22/SBO/key2 P21/SBI/key1 P20/NSYNC/key0 P13/PWMO3 P12/PWMO2 P11/PWMO1 P10/PWMO0 P03
Support Tool
In-circuit Emulator EPROM Built-in Type
Type ROM (x 8-bit) RAM (x 4-bit)
PX-ICE1500 + PX-PRB15G1601-LQFP064-P-1414 MN15GP1601 16 K 512 0.5 s at 1/4 frequency dividing (at 3.0 V to 5.5 V, 8 MHz) 1.0 s at 1/4 frequency dividing (at 2.4 V to 5.5 V, 4 MHz) 2.0 s at 1/8 frequency dividing (at 2.3 V to 5.5 V, 4 MHz) Package LQFP064-P-1414 *Pb free
Minimum instruction execution time
SEG28 / AD6 SEG29 / AD7 VREF+ VDD VLC1 VLC2 VLC3 OSC1 OSC2 XI XO NRST VSS P00 P01 P02
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
LQFP064-P-1414 *Pb free
MAC00001BEM
213
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company.
Please read the following notes before using the datasheets
A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.
2001 MAR

▲Up To Search▲

Price & Availability of MN15G1601

	To Download MN15G1601 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .