Part Number Hot Search : 
DC100210 7447040 D5331M CM7257 CM7257 IC16F8 20101 SIP2805
Product Description
Full Text Search
 

To Download V23809-J307-C13 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 without cutout
V23809-J307-C10 with cutout V23809-J307-C13
Preliminary
AC/DC Coupled Multimode 850 nm 1.0625 GBd Fibre Channel 1x9 Transceiver
Dimensions in (mm) inches
View Z (Lead cross section and standoff size) (0.730.1) .028.004 (1.50.1) .06.004
(40.2) .158.008 (a)
(11.5 max) .453 max. (2) .080 Optical Centerline (0.750.1) .030.004
(7 .42-0.15) .292-.006 (9.6+0.1) .378+.004 6.375 .251
9x (0.8) min. .032 min. 11x 0.1 M .004 M
PC board 2x
PC board thickness 11x (0.5) typ. .020 typ. (0.25) typ. .010 typ. (25.40.1) 9x 1.004 A 0.3 M 8x 2.54=20.32 .012 M A 8x .100 =.800
Z
123456789
0.1 M .004 M
0.3 M A .012 M A Top View (2.50.1) 8x 2.54=20.32 .098.004 Cutout 8x .100 =.800 Rx 12.7 .500 Tx (20 -1) .787 -.040 (2.54) .100 (2.54) .100
(1.4-0.05) .055-.002 (b)
DUPLEX SC RECEPTACLE
20.32 .800
(1.90.1) 2x .075.004
A
a. Different length of pins available. maximum: (7 .295 .5) b. Isolated posts on request
(15.880.5) 20.32 .625.020 .800 (38.620.1) 1.52.004
(12.60.3) .496.012
Absolute Maximum Ratings Exceeding any one of these values may destroy the device immediately. Package Power Dissipation(1) ........................................................ 1.5 W Supply Voltage (VCC-VEE).................................................................. 6 V Data Input Levels (PECL) ....................................................... VCC-0.7 V Differential Data Input Voltage........................................................ 2.5 V Operating Case Temperature...............................................0C to 70 C Storage Ambient Temperature......................................... -40C to 85C Soldering Conditions, Temp/Time (MIL -STD 883C, Method 2003) ......................................... 250C/5.5s
Note 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V.
FEATURES * Compliant with existing standards * Compact integrated transceiver unit with - Laser diode transmitter - Photodiode receiver - Duplex SC receptacle * Class 1 FDA and IEC laser safety compliant * FDA Accession No. 9520890-05 * Single power supply (5 V)* * Signal detect indicator * PECL differential inputs and outputs * Process plug included * Wave solderable and washable with process plug inserted
*3.3 V version in 9.8 mm package available in June 1998 (V23816-J307-C313). Check web site for data sheet.
Semiconductor Group
DESCRIPTION This data sheet describes the Siemens multimode 1.0625 GBd Fibre Channel transceiver, which complies with the Fibre Channel - Physical and Signaling Interface (FC-PH), ANSI X3T11 Fibre Channel Physical Standard class 100-M5-SN-I. The appropriate fiber optic cable is 50 m (from 2 m up to 500 m) multimode fiber with Duplex SC connector. The use of 62.5 m multimode fiber will decrease the transmission distance.
APRIL 1998
DESCRIPTION (continued) The Siemens multimode 1.0625 GBd Fibre Channel transceiver is a single unit comprised of a transmitter, a receiver, and an SC receptacle. This design frees the customer from many alignment and PC board layout concerns. The module is designed for low cost LAN and WAN applications. It can be used as the network end device interface in mainframes, workstations, servers, and storage devices, and in a broad range of network devices such as bridges, routers, intelligent hubs, and switches. This transceiver operates at 1.0625 Gbits per second from a single power supply (+5 V). The full differential data inputs and outputs are PECL compatible. Functional Description of 1x9 Pin Row Transceiver This transceiver is designed to transmit serial data via multimode cable. Functional Diagram
Automatic Shut-Down
LEN TD TD Laser Coupling Unit e/o
TECHNICAL DATA The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Recommended Operating Conditions
Parameter Case Temperature Power Supply Voltage Supply Current(1) Transmitter Differential Data Input Voltage(2) Input Data Rise/Fall Time, 20%-80% Receiver Input Center Wavelength C 770 860 nm VIL-VCC tR, tF 0.3 0.9 450 V ps Symbol TC ICC Min. Typ. Max. Units 0 5.0 220 70 5.25 300 C V mA
VCC-VEE 4.75
Laser Driver Power Control
Monitor
Notes 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V. 2. Data inputs are AC coupled with 100 differential termination built into the transceiver.
Laser
Transmitter Electro-Optical Characteristics
Transmitter
Multimode Fiber
o/e
Symbol Min. Typ. Max. Units PO C ER VTH tRES EO DJ tR, tF 140 57 20 0.45 ns 9 2.9 240 560 -10 830 850 -5 860 4 dB V ms % dBm nm
Launched Power (Average)(1) Center Wavelength Spectral Width (FWHM) Extinction Ratio (Dynamic) Reset Threshold of TXVCC(2) Reset Time Out(2) Eye Opening Deterministic Jitter Optical Rise/Fall Time, 10%-90%
RX Coupling Unit o/e
RD RD SD
Receiver
The receiver component converts the optical serial data into PECL compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether an optical signal is present. The transmitter converts PECL compatible electrical serial data (TD and TDnot) into optical serial data. Data lines are AC coupled with differential 100 termination. The transmitter contains a laser driver circuit that drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee constant output power of the laser over temperature and aging. The power control uses the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the operating limits. Single fault condition is ensured by means of an integrated automatic shutdown circuit that disables the laser when it detects transmitter failures. A reset is only possible by turning the power off, and then on again. The transceiver contains a supervisory circuit to control the power supply. This circuit makes an internal reset signal whenever the supply voltage drops below the reset threshold. It keeps the reset signal active for at least 140 milliseconds after the voltage has risen above the reset threshold. During this time the laser is inactive.
Notes 1. Into multimode fiber (62.5 m or 50 m diameter). 2. Laser power is shut down if power supply is below VTH and switched on if power supply is above VTH after tRES.
Semiconductor Group 2
V23809-J307-C10/C13, AC/DC Multimode 850 nm 1.0625 GBd FC 1x9 Transceiver
Receiver Electro-Optical Characteristics
Receiver Sensitivity (Average Power)(1) Saturation (Average Power) Signal Detect Assert Level(2) Signal Detect Deassert Level(3) Signal Detect Hysteresis Signal Detect Assert Time Signal Detect Deassert Time Symbol Min. PIN PSAT PSDA PSDD PSDA- PSDD tASS tDAS -1950 -1025 -30 0 -24 -27 3 100 350 -1600 -720 400 ps mV dB s -20 Typ. -19 Max. -16 Units dBm
LASER SAFETY This laser transceiver is a Class 1 laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated under recommended operating conditions. Caution The use of optical instruments with this product will increase eye hazard! General Restrictions Classification is valid only if the module is operated within the specified temperature and voltage limits. The system using the module must provide power supply protection that guarantees that the system power source will cease to provide power if the maximum recommended operation limit or more is detected on the +5 V at the power source. The case temperature of the module must be in the temperature range given in the recommended operating limits. These limits guarantee the laser safety. Usage Restrictions The optical ports of the modules shall be terminated with an optical connector or with a dust plug.
Note Failure to adhere to the above restrictions could result in a modification that is considered an act of "manufacturing, and will require, under " law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).
Output Low Voltage(4) VOL- VCC Output High Voltage(4) VOH- VCC Output Data Rise/Fall Time, 20%-80% tR, tF
Notes 1 For a BER of less than 1 x 10E-12. Measured with a 27-1 PRBS and ER=9 dB. 2. An increase in optical power above the specified level will cause the SIGNAL DETECT output to switch from a Low state to a High state. 3. A decrease in optical power below the specified level will cause the SIGNAL DETECT to change from a High state to a Low state. 4. PECL compatible. Load is 50 into VCC-2 V. Measured under DC conditions. For dynamic measurements a tolerance of 50 mV should be added. VCC=5 V.
Laser Data
Wavelength Total output power (as defined by IEC: 50 mm aperture at 10 cm distance) Total output power (as defined by FDA: 7 mm aperture at 20 cm distance) Beam divergence 850 nm <400 W <70 W 12
Pin Description 1x9 Pin Row
Pin Name RxVEE RD RDn SD Rx Ground Rx Output Data Rx Output Data RX Signal Detect Level Power Supply PECL Output PECL Output PECL Output active high Power Supply Power Supply Pin # Description 1 2 3 4 Negative power supply, normally ground Receiver output data Inverted receiver output data A high level on this output shows that there is an optical signal Positive power supply, +5 V Positive power supply, +5 V Inverted transmitter input data Transmitter input data Negative power supply, normally ground Support stud (floating)
Required Labels
FDA
Complies with 21 CFR 1040.10 and 1040.11
IEC
Class 1 Laser Product
Laser Emission
Indication of laser aperture and beam
RxVCC Rx +5 V TxVCC TDn TD TxVEE Case Tx +5 V
5 6 7 8 9 S1/2
Tx Input Data PECL Input Tx Input Data PECL Input Tx Ground Ground Power Supply Power Supply
Semiconductor Group 3
V23809-J307-C10/C13, AC/DC Multimode 850 nm 1.0625 GBd FC 1x9 Transceiver
Regulatory Compliance
Feature Electrostatic Discharge (ESD) to the Electrical Pins Immunity: Electrostatic Discharge (ESD) to the Duplex SC Receptacle Immunity: Radio Frequency Electromagnetic Field Emission: Electromagnetic Interference (EMI) Standard MIL-STD 883C Method 3015.4 EN 61000-4-2 IEC 1000-4-2 EN 61000-4-3 IEC 1000-4-3 FCC Class B EN 55022 Class B CISPR 22 Comments Class 1 (>1000 V) Discharges of 15kV with an air discharge probe on the receptacle cause no damage. With a field strength of 10 V/m rms, noise frequency ranges from 10 MHz to 1 GHz. No effect on transceiver performance between the specification limits. Noise frequency range: 30 MHz to 1 GHz
APPLICATION NOTE FOR 850 NM GBD FIBRE CHANNEL 1X9 TRANSCEIVER
TXGND TxD VCSEL Driver 100R TxD
9 8
VCC SerDes 5V
VCC TX+ ECL/PECL Driver
7
TX-
R7
R8
VCCTx
6 C1
L1 VCC 5V
Siemens Transceiver SiemensTransceiver V23809-J307-C10/C13 V23809-J307-C10
Serializer/ Deserializer
VCCRx
5 C2
L2 C3 Gigabit Transceiver Chip
Signal Detect
SD
4
SD to upper level
R1
R9 PreAmp Limiting Amplifier RD- RxD 3 C4
R2
RD- Receiver PLL etc.
RD+
RxD
2
C5
RD+
R3 R4
C1/2/3 C4/5 L1/2 R1/2 R3/4
= = = = =
4.7 F 10 nF 1 H 82 Ohm (depends on SerDes chip used) 130 Ohm (depends on SerDes chip used)
R5
R5/6 = 200 Ohm 270 Ohm R7/8 = Biasing (depends on SerDes chip) R9 = 500 Ohm Place R1/2/3/4/7/8 close to SerDes chip Place R5/6 close to Siemens transceiver
Values of R1/2/3/4 may vary as long as proper 50 termination to VEE or 100 differential is provided. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module VCCRX/VCCTX.
R6
RxGND
1
The transceiver contains an automatic shutdown circuit. Reset is only possible if the power is turned off, and then on again. (VCCTX switched below VTH). Application Board available on request.
Siemens Microelectronics, Inc. * Optoelectronics Division * 19000 Homestead Road * Cupertino, CA 95014 USA Siemens Semiconductor Group * Fiber Optics * Wernerwerkdamm 16 * Berlin D-13623, Germany Siemens K.K. * Fiber Optics * Takanawa Park Tower * 20-14, Higashi-Gotanda, 3-Chome * Shinagawa-ku * Tokyo 141, Japan www.smi.siemens.com/opto.html (USA) * www.siemens.de/Semiconductor/products/37/376.htm (Germany)


▲Up To Search▲   

 
Price & Availability of V23809-J307-C13

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X