 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NEW 1 mm Pitch Double Rows Low Profile Board-to-Cable Connectors DF20 series 5.4 Socket DF20A**DS-1C DF20F(G)**DP-1V Pin Header 5.8 Cable PCB DF20A**DS-1C Socket Cable 6.2 DF20F **DP-1H Pin Header 5.5 PCB DF20A-**DS-1C Socket DF20F(G)-**DP-1V Pin Header 1 sFeatures 1. Contact Pitch 1 mm contact pitch allows reliable solder and cable termination. Narrower external width and length 2. Low profile Total mating height above the board is 5.8 mm for the straight type and 5.5 mm for the right angle type. 3. Reliable electrical connection wipe Effective electrical connection is assured with a 1mm wipe of mating contacts. 4. Narrower external width and length Redesigned metal fittings decreased the overall length of the board- mount receptacle and permit end-to-end mounting of several connectors. Metal fitting 5. Automatic equipment board placement Straight type pin headers are supplied with a 5.4 mm X 4.6mm flat platform to allow vacuum pick-up and placement on the board. 6. Product variations (1) Available with 10, 20, 30, 40, and 50 contacts. (2) Pin headers are available in two types: with or without board positioning bosses. (3) Depending on specific application pin headers can be ordered in straight or right angle types. DF20F-****SCFA Contact sApplications Notebook PC, small office automation equipment, small consumer devices, portable devices. Any application requiring low profile reliable board-to-cable connection with a AWG #28, AWG#30, AWG#32 conductors. 1mm Pitch, Double Rows 2002.5 1 sProduct Specifications Rating AWG#28 : 1A Operating temperature range -35C to 85C (Note 1,2) Storage temperature range -10C to 60C (Note 2) AWG#30 : 0.9A AWG#32 : 0.7A Storage humidity range -40% to 70% Rated voltage Operating humidity range -20% to 80% 100V AC Rated current Specifications 500Mo min. 30mo max. Measured at 100V DC Conduction of 300V AC applied for 1 minute Measure at 100mA. Measured with a steel pin of 0.2 0.005 thickness Frequency of 10 to 55 Hz, single amplitude of 0.75 mm, in 3 directions for 2hours (-55c:30min / 5c to 35c: 2 to 3min / 85c:30min / 5c to 35c:2 to 3min ) for 5 cycles 50 cycles Reflow: At the recommended temperature profile, manual solder: Soldering iron temperature of 300C for 3 seconds Conditions Item 1.Insulation resistance 3.Contact resistance 2.Withstanding voltage No flashover or insulation breakdown 4.Insertion-Extraction force Min. 0.2 N (20 gf), Max. 2 N (200 gf) 4.(per contact) 5.Vibration 6.Humidity 7.Temperature cycle 9.Resistance to Soldering heat No electrical discontinuity of 1s min. Contact resistance of 30mo max,insulation resistance of 500Mo min. No deformation of the insulator parts that will affect performance Contact resistance of 30mo max., insulation resistance of 100Mo min. Temperature of 402c, humidity of 90% to 95%, left standing for 96 hours 8.Mechanical operation Contact resistance of 30mo max. Note1: Includes temperature rise caused by current flow. Note2: The term "storage" refers to products stored for long periods of time prior to mounting and use. Note2: Operating temperature range and Humidity range covers non-conducting conditions of installed connectors in storage, Note2: shipment or transportation. sMaterials Item Socket Socket contact Part Insulator Contact Insulator Pin header Contact Metal Fitting Material Polyamide Phosphor bronze Polyamide Phosphor bronze Brass Finish Color : Beige Gold plating Color : Beige Gold plating Remarks UL94V-0 ---------UL94V-0 ---------- V type: Solder plating H type: Tin-Copper plating (Pb free) sOrdering Information qConnectors DF 20 # - * DS - 1 C 1 2 3 4 5 6 7 5 Connector type DS: Double-row socket DP: Double-row pin header 6 Contact pitch: 1 mm 7 Type of housing, header 7 C: Crimp housing V: Straight SMT header H: Right angle SMT header 1 Series name : DF 2 Series No. : 20 3 Boss Type sPin header sF: Without boss sG: With boss sCrimp socket: A 4 Number of contacts: 10, 20, 30, 40, 50 qContacts DF20 F - 2830 SCF A 1 2 3 4 3 Contact & packaging type SCF: Socket contact reel 4 Plating type A: Gold plating (* *) 5 5 Packaging Specifications Blank: 1 reel = 10,000 pieces 41: 1 reel = 20,000 pieces 1F 2 Applicable wire size 2830: AWG #28 to 30 3032: AWG #30 to 32 2 sDouble Row Socket Contact No. 2 Contact No. * Contact No. 1 Contact No. *-1 5th contact marking Shown with terminated and installed contacts Unit: mm B 14.0 19.0 14.0 19.0 24.0 Contact No. 1 mark Product No. DF20A-10DS-1C DF20A-20DS-1C DF20A-30DS-1C DF20A-40DS-1C DF20A-50DS-1C CL No. 686-0020-3 686-0021-6 686-0022-9 686-0023-1 686-0024-4 Number of Contacts 10 20 30 40 50 A 17.2 12.2 17.2 22.2 27.2 [Specifications number]-*, (**) (59): Gold plating, embossed tape packaging Note: Sales quantities are by the package unit (containing 100 pieces). Please order by package unit. sSocket Crimp Contacts Product No. DF20F-2830SCFA(**) DF20F-3032SCFA(**) CL No. 686-0042-6-** 686-0043-9-** Type of contacts Reel contacts Quantity See specifications number column Plating type Gold plating [Specifications number] -*, (**) Blank 1 reel : 10,000 pieces 41 1 reel : 20,000 pieces 0.7 1.45 qApplicable Wire (Tin plated solid soft conductor) Applicable Wire Size (Stranded wire conductor) AWG #28 (7/0.127 mm) 3.3 Jacket diameter 0.5mm to 0.6 mm 0.9 2 0.5 AWG #30 (7/0.1 mm) AWG #32 (7/0.08 mm) qRecommended wire qUL1571 qStrip length q1.2 to 1.9 mm Note: When using other than the recommended wire, contact your nearest Hirose representative. qApplicable Crimping Tools Type Applicator Press CL No. 901-4572-6 901-0005-4 Product No. AP105-DF20-2830S CM-105 HT302/DF20B-2830S Manual crimping tool 901-4540-6 Note 1: Hirose Electric will not be responsible for any problems caused by use of tools other than specified. Note 2: The manual crimping tool can be also used for cutting-off individual contacts from the reel. Note 3: Customers that already have DF13 Series Hirose's press units and applicators will be able to use them for DF20 Series crimp terminations by replacing of only crimper and anvil. Note4: The crimping tool for the DF20F-3032SCFA can also be used with the DF20F-2830SCFA. sReplacement Parts List for Applicator Type Insulation crimper Wire crimper Product No. AP105-DF20-2830S(61) AP105-DF20-2830S(62) CL No. 901-4572-6-61 901-4572-6-62 901-4572-6-63 Insulation anvil and wire anvil AP105-DF20-2830S(63) 3 s Double Row Straight Pin header Contact No.3 Contact No.1 P=1 B A Contact No. **-1 Indication of number of contacts ** Contact No. ** 6.4 Contact No.2 0.2 5.4 0.7 O0.5 C D 4.6 1.9 A 0.2 BPCB Footprints A 0.05 P=10.03 0.60.05 1.8 0.1 0.50.05 0.90.05 0.850.1 Contact No. 1 marking 1.90.05 D0.05 Note 1:Shaded area must be free of any electrically conductive traces to avoid contact with soldered pin header terminations. Note 2: Required only for pin headers supplied with the positioning boss. Unit: mm Product No. DF20F-10DP-1V ( * * ) DF20F-20DP-1V ( * * ) DF20F-30DP-1V ( * * ) DF20F-40DP-1V ( * * ) DF20F-50DP-1V ( * * ) DF20G-10DP-1V ( * * ) DF20G-20DP-1V ( * * ) DF20G-30DP-1V ( * * ) DF20G-40DP-1V ( * * ) DF20G-50DP-1V ( * * ) CL No. CL686-0032-2- * * CL686-0033-5- * * CL686-0034-8- * * CL686-0035-0- * * CL686-0036-3- * * CL686-0037-6- * * CL686-0038-9- * * CL686-0039-1- * * CL686-0040-0- * * CL686-0041-3- * * Number of contacts 10 20 30 40 50 10 20 30 40 50 7.2 0.1 40.1 O0 Note1: Order embossed tape packaging items by the reel. (1 reel contains 1,000 pieces) Note2: Vacuum pick-up platforms are included with embossed tape packaged connectors. .1 +0 0 .7 A 14.0 19.0 14.0 19.0 24.0 14.0 19.0 14.0 19.0 24.0 B 17.3 12.3 17.3 22.3 27.3 17.3 12.3 17.3 22.3 27.3 C --------------------16.6 11.6 16.6 21.6 26.6 D 15.7 10.7 15.7 20.7 25.7 15.7 10.7 15.7 20.7 25.7 Remarks Without boss With boss [Specifications number]-*, (**) (59): Gold plating, embossed tape packaging 4 sDouble Row Right angle Pin header Contact No.1 Contact No.3 Contact No.**-1 Contact No.1 marking Contact No.2 B Contact No.** 5 A Indication of number of contacts ** P= 1 A 0.2 6.2 0.2 C BPCB Footprints 1.4 +0.1 0 2.75 0.05 +0.1 0 2.45 0.6 0.05 P= 1 0.03 A 0.05 0.75 0.1 C 0.1 Note : Shaded area must be free of any electrically conductive traces to avoid contact with soldered pin header terminations. Unit: mm Product No. DF20F -10DP-1H ( * * ) DF20F -20DP-1H ( * * ) DF20F -30DP-1H ( * * ) HRS No. 686-0027-2 ( * * ) 686-0028-5 ( * * ) 686-0029-8 ( * * ) Number of contacts 10 20 30 40 50 1.4 +0.1 0 3.8 0.05 A 24.0 29.0 14.0 19.0 24.0 B 27.5 12.5 17.5 22.5 27.5 C 26.2 11.2 16.2 21.2 26.2 Remarks Without boss [Specifications number]-*, (**) (59): Gold plating, embossed tape packaging DF20F -40DP-1H ( * * ) Reserved for product expansion DF20F -50DP-1H ( * * ) Reserved for product expansion Note:Order embossed tape packaging items by the reel. (1 reel contains 1,000 pieces) 5.5 5 BEmbossed Carrier Tape Dimensions qStraight pin header 4 0.1 .5 +0 0 .1 O1 12 0.1 C 0.1 B 0.1 1.7 +0.15 0 0.20.05 1.750.1 2 0.1 R0. 7 5 A 0.3 0.4 1.5 +0.1 0 Unreeling direction 7.9 qRight angle pin header 20.1 120.1 1.75 0.1 C 0.1 B 0.1 1.7 +0.15 0 0.20.05 40.1 .1 +0 0 R0 .75 A 0.3 0.4 O1 .5 1.5 +0.1 0 Unreeling direction (7.4) qReel dimensions Product No. DF20F(G)-10DP-1V DF20F(G)-20DP-1V DF20F(G)-30DP-1V DF20F(G)-40DP-1V DF20F(G)-50DP-1V DF20F-10DP-1H DF20F-20DP-1H DF20F-30DP-1H Number of Contacts A 16 24 32 44 44 16 24 32 44 44 B ----------28.4 40.4 40.4 ----------28.4 40.4 40.4 C 17.5 11.5 14.2 20.2 20.2 17.5 11.5 14.2 20.2 20.2 D 16.4 24.4 32.4 44.4 44.4 16.4 24.4 32.4 44.4 0 2 0.5 Product name label 10 20 30 40 50 10 20 30 40 50 O1.5 mm diameter feed hole depth O21 0.8 * * DF20F-40DP-1H DF20F-50DP-1H 44.4 .2 2 0.5 D +2 0 6 O1 3 * Reserved for product expansion O380 2 (O80) BUsage recommendation 1. Recommended Soldering Temperature Profile for IR Reflow. Temperature IR Reflow Preheating: 150C for 60 sec. to 120 sec. Soldering: 235C5C for 10 sec. max. ... Maximum 240C 220C min. 10s to 30s ... 220C Maximum 240C 220C Preheating Soldering Note 1: Up to 2 cycles of reflow soldering are possible under the same conditions, provided that there is a return to normal temperature between the first and second cycle. Note 2: The temperature indicates the board surface temperature at the points of contacts with the connector terminals. 2.Recommended Manual Soldering Conditions 3. Recommended Solder Screen Thickness 4. Board Warping 5. Cleaning Conditions 6. Wiring Termination Conditions Soldering temperature: 290C 10C, Soldering time: within 3 sec. 0.15mm Maximum of 0.03 mm at the connector center section, with both ends of the connector as reference points. Refer to "Nylon Connector Use Handbook." Refer to "Nylon Connector Use Handbook." Crimp contacts should be handled with care as not to cause any deformation or damage affecting the performance or termination. Excessive twisting and pulling on wires during mating/un-mating should be avoided as it may cause damage to connectors. 7. Mating / un-mating precautions 7 |
Price & Availability of DF20F-10DP-1C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |