|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Final Electrical Specifications LTC3719 2-Phase, 5-Bit VID, Current Mode, High Efficiency, Synchronous Step-Down Switching Regulator FEATURES s DESCRIPTIO December 2001 s s s s s s s s s s s s s s s Output Stages Operate Antiphase Reducing Input and Output Capacitance Requirements and Power Supply Induced Noise Dual Input Supply Capability for Load Sharing 5-Bit AMD (Hammer) CPU VID Code: VOUT = 0.8V to 1.55V 1% Output Voltage Accuracy True Remote Sensing Differential Amplifier Power Good Output Voltage Monitor Supports Active Voltage Positioning Current Mode Control Ensures Current Sharing OPTI-LOOP(R) Compensation Minimizes COUT Three Operational Modes: PWM, Burst and Cycle Skip Programmable Fixed Frequency: 150kHz to 300kHz Wide VIN Range: 4V to 36V Operation Adjustable Soft-Start Current Ramping Internal Current Foldback and Short-Circuit Shutdown Overvoltage Soft Latch Eliminates Nuisance Trips Available in 36-Lead Narrow (0.209) SSOP Package The LTC(R)3719 is a 2-phase, VID programmable, synchronous step-down switching regulator controller that drives two N-channel external power MOSFET stages in a fixed frequency architecture. The 2-phase controller drives its two output stages out of phase at frequencies up to 300kHz to minimize the RMS ripple currents in both input and output capacitors. The 2-phase technique effectively multiplies the fundamental frequency by two, improving transient response while operating each channel at an optimum frequency for efficiency. Thermal design is also simplified. An operating mode select pin (FCB) can be used to regulate a secondary winding or select among three modes including Burst Mode(R) operation for highest efficiency. An internal differential amplifier provides true remote sensing of the regulated supply's positive and negative output terminals as required in high current applications. The RUN/SS pin provides soft-start and optional timed, short-circuit shutdown. Current foldback limits MOSFET dissipation during short-circuit conditions when the overcurrent latchoff is disabled. OPTI-LOOP compensation allows the transient response to be optimized for a wide range of output capacitors and ESR values. APPLICATIO S s AMD (Sledgehammer and Clawhammer) CPU Supply , LTC and LT are registered trademarks of Linear Technology Corporation. OPTI-LOOP and Burst Mode are registered trademarks of Linear Technology Corporation. TYPICAL APPLICATIO 0.1F 220pF FCB RUN/SS 3.3k ITH SGND PGOOD 5 VID BITS VIN TG1 BOOST1 SW1 S 10F 35V x6 0.47F 1H S 0.002 LTC3719 BG1 PGND D1 VID0-VID4 EAIN ATTENOUT ATTENIN VDIFFOUT VOS - VOS + SENSE1 + SENSE1 - TG2 BOOST2 SW2 BG2 SENSE2 + SENSE2 - D2 0.47F 1H 0.002 VDD_CORE 0.8V TO 1.55V 45A Figure 1. High Current Dual Phase Step-Down Converter 3719i Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. + INTVCC 10F U + COUT 270F 2V x4 3716 F01 U U VIN 5V TO 28V 1 LTC3719 ABSOLUTE (Note 1) AXI U RATI GS PACKAGE/ORDER I FOR ATIO TOP VIEW RUN/SS SENSE1 + SENSE1 - EAIN PLLFLTR PLLIN FCB ITH SGND - + Input Supply Voltage (VIN).........................36V to - 0.3V Topside Driver Voltages (BOOST1,2) .........42V to - 0.3V Switch Voltage (SW1, 2) .............................36V to - 5 V SENSE1+, SENSE2 +, SENSE1-, SENSE2 - Voltages ................... (1.1)INTVCC to - 0.3V EAIN, VOS+, VOS-, EXTVCC, INTVCC, RUN/SS, VBIAS, ATTENIN, ATTENOUT, PGOOD, NO_CPU, VID0-VID4, Voltages ...............................7V to - 0.3V Boosted Driver Voltage (BOOST-SW) ..........7V to - 0.3V PLLFLTR, PLLIN, VDIFFOUT, FCB Voltages ................................... INTVCC to - 0.3V ITH Voltage ................................................2.7V to - 0.3V Peak Output Current <1s(TG1, 2, BG1, 2) ................ 3A INTVCC RMS Output Current ................................ 50mA Operating Ambient Temperature Range (Note 2) .............................................. - 40C to 85C Junction Temperature (Note 3) ............................. 125C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C 1 2 3 4 5 6 7 8 9 36 PGOOD 35 TG1 34 SW1 33 BOOST1 32 VIN 31 BG1 30 EXTVCC 29 INTVCC 28 PGND 27 BG2 26 BOOST2 25 SW2 24 TG2 23 ATTENIN 22 VBIAS 21 VID4 20 VID3 19 VID2 ORDER PART NUMBER LTC3719EG VDIFFOUT 10 VOS VOS 11 12 SENSE2 - 13 SENSE2 + 14 ATTENOUT 15 NO_CPU 16 VID0 17 VID1 18 G PACKAGE 36-LEAD PLASTIC SSOP TJMAX = 125C, JA = 85C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS SYMBOL VEAIN VSENSEMAX IINEAIN VLOADREG PARAMETER Regulated Feedback Voltage Maximum Current Sense Threshold Feedback Current Output Voltage Load Regulation (Note 4) Main Control Loop The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted. CONDITIONS ITH Voltage = 1.2V; Measured at VEAIN (Note 4) q q MIN 0.594 62 TYP 0.600 75 -5 MAX 0.606 88 - 50 0.5 - 0.5 0.02 0.63 -1 4.8 0.68 4 UNITS V mV nA % % %/V V A V V V mmho V/mV 3719i (Note 4) Measured in Servo Loop, ITH Voltage: 1.2V to 0.7V Measured in Servo Loop, ITH Voltage: 1.2V to 2V VIN = 3.6V to 30V (Note 4) q q 0.1 - 0.1 0.002 0.57 0.6 - 0.17 4.3 VREFLNREG VFCB IFCB VBINHIBIT VOVL UVLO gm gmOL Reference Voltage Line Regulation Forced Continuous Threshold Forced Continuous Current Burst Inhibit (Constant Frequency) Threshold Output Overvoltage Threshold Undervoltage Lockout Transconductance Amplifier gm Transconductance Amplifier Gain q Measured at FCB pin Measured at VEAIN VIN Ramping Down ITH = 1.2V, Sink/Source 5A (Note 4) ITH = 1.2V, (gm * ZL; No Ext Load) (Note 4) q 0.64 3 0.66 3.33 3 1.5 2 U W U U WW W LTC3719 ELECTRICAL CHARACTERISTICS SYMBOL IQ PARAMETER Input DC Supply Current Normal Mode Shutdown Soft-Start Charge Current RUN/SS Pin ON Threshold RUN/SS Pin Latchoff Arming RUN/SS Discharge Current Shutdown Latch Disable Current Total Sense Pins Source Current Maximum Duty Factor Top Gate Transition Time: Rise Time Fall Time Bottom Gate Transition Time: Rise Time Fall Time Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time Minimum On-Time Internal VCC Voltage INTVCC Load Regulation EXTVCC Voltage Drop EXTVCC Switchover Voltage EXTVCC Switchover Hysteresis Operating Supply Voltage Range Resistance Between ATTENIN and ATTENOUT Pins Resistive Divider Error VID0 to VID4 Pull-Up Resistance VID0 to VID4 Logic Threshold Low VID0 to VID4 Logic Threshold High VID0 to VID4 Leakage NO_CPU Maximum Output Voltage VBIAS < VID0-VID4 < 7V INO_CPU = 2mA 1.6 1 0.4 (Note 8) q The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted. CONDITIONS (Note 5) VRUN/SS = 0V VRUN/SS = 1.9V VRUN/SS Rising VRUN/SS Rising from 3V Soft Short Condition VEAIN = 0.5V, VRUN/SS = 4.5V VEAIN = 0.5V Each Channel: VSENSE1 -, 2 - = VSENSE1+, 2 + = 0V In Dropout (Note 6) CLOAD = 3300pF CLOAD = 3300pF (Note 6) CLOAD = 3300pF CLOAD = 3300pF CLOAD = 3300pF Each Driver (Note 6) CLOAD = 3300pF Each Driver (Note 6) Tested with a Square Wave (Note 7) 6V < VIN < 30V, VEXTVCC = 4V ICC = 0 to 20mA, VEXTVCC = 4V ICC = 20mA, VEXTVCC = 5V ICC = 20mA, EXTVCC Ramping Positive ICC = 20mA, EXTVCC Ramping Negative 2.7 10 - 0.35 40 0.4 0.25 q MIN TYP 1.2 20 MAX UNITS mA A A V V A A A % 40 1.9 4.5 4 5 IRUN/SS VRUN/SS VRUN/SSLO ISCL ISDLHO ISENSE DFMAX TG1, 2 tr TG1, 2 tf BG1, 2 tr BG1, 2 tf TG/BG t1D BG/TG t2D tON(MIN) VINTVCC VLDO INT VLDO EXT VEXTVCC VLDOHYS VBIAS RATTEN ATTENERR RPULLUP VIDTHLOW VIDTHHIGH VIDLEAK VNO_CPU - 0.5 1.0 0.5 - 85 98 -1.2 1.5 4.1 2 1.6 - 60 99.5 30 40 30 20 90 90 180 90 90 90 90 ns ns ns ns ns ns ns Internal VCC Regulator 4.8 5.0 0.2 80 4.5 4.7 0.2 5.5 5.2 1.0 160 V % mV V V V k % k V V A V VID Parameters 3719i 3 LTC3719 ELECTRICAL CHARACTERISTICS SYMBOL fNOM fLOW fHIGH RPLLIN IPLLFLTR PARAMETER Nominal Frequency Lowest Frequency Highest Frequency PLLIN Input Resistance Phase Detector Output Current Sinking Capability Sourcing Capability Controller 2-Controller 1 Phase PGOOD Voltage Low PGOOD Leakage Current PGOOD Trip Level, Either Controller Oscillator and Phase-Locked Loop The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted. CONDITIONS VPLLFLTR = 1.2V VPLLFLTR = 0V VPLLFLTR 2.4V MIN 190 120 280 TYP 220 140 310 50 fPLLIN < fOSC fPLLIN > fOSC - 15 15 180 IPGOOD = 2mA VPGOOD = 5V VEAIN with Respect to Set Output Voltage VEAIN Ramping Negative VEAIN Ramping Positive VAMPMD = 0V 0V < VCM < 5V; VAMPMD = 0V Measured at VOS + Input; VAMPMD = 0V -8 8 0.995 46 - 10 10 1 55 80 0.1 0.3 1 - 12 12 1.005 MAX 250 160 360 UNITS kHz kHz kHz k A A Deg V A % % V/V dB k RRELPHS VPGL IPGOOD VPG PGOOD Output Differential Amplifier/Op Amp Gain Block ADA CMRRDA RIN Differential Amplifier Gain Common Mode Rejection Ratio Input Resistance Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC3719 is guaranteed to meet performance specifications from 0C to 70C. Specifications over the - 40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: LTC3719EG: TJ = TA + (PD * 85C/W) Note 4: The LTC3719 is tested in a feedback loop that servos VITH to a specified voltage and measures the resultant VEAIN. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: The minimum on-time condition corresponds to the on inductor peak-to-peak ripple current 40% IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 8: Each built-in pull-up resistor attached to the VID inputs also has a series diode to allow input voltages higher than the VIDVCC supply without damage or clamping (see the Applications Information section). 3719i 4 LTC3719 TYPICAL PERFOR A CE CHARACTERISTICS Efficiency vs Load Current (3 Operating Modes) (Figure 13) 100 90 80 EFFICIENCY (%) EFFICIENCY (%) Burst Mode OPERATION 80 VIN = 5V 60 VIN = 8V VIN = 12V VIN = 20V 40 VOUT = 1.6V VEXTVCC = 0V FREQ = 200kHz VFCB = 0V 0.1 1 10 LOAD CURRENT (A) 100 3719 G02 60 50 40 30 20 10 0 0.01 0.1 EFFICIENCY (%) 70 FORCED CONTINUOUS MODE CONSTANT FREQUENCY (BURST DISABLED) VIN = 5V VOUT = 1.6V FREQ = 200kHz 10 1 LOAD CURRENT (A) 100 3719 G01 Supply Current vs Input Voltage and Mode 1000 ON 800 250 INTVCC AND EXTVCC SWITCH VOLTAGE (V) EXTVCC VOLTAGE DROP (mV) SUPPLY CURRENT (A) 600 400 200 SHUTDOWN 0 0 5 20 15 10 25 INPUT VOLTAGE (V) 30 35 Internal 5V LDO Line Reg 5.1 5.0 ILOAD = 1mA INTVCC VOLTAGE (V) 4.9 4.8 4.7 4.6 4.5 4.4 0 5 20 15 25 10 INPUT VOLTAGE (V) 30 35 3719 G07 VSENSE (mV) VSENSE (mV) UW 3719 G04 Efficiency vs Load Current (Figure 13) 100 100 Efficiency vs Input Voltage (Figure 13) IOUT = 20A VOUT = 1.6V 90 80 70 20 60 0 50 5 15 10 INPUT VOLTAGE (V) 20 3719 G03 EXTVCC Voltage Drop 5.05 5.00 4.95 4.90 4.85 4.80 4.75 INTVCC and EXTVCC Switch Voltage vs Temperature INTVCC VOLTAGE 200 150 100 50 EXTVCC SWITCHOVER THRESHOLD 0 0 10 30 20 CURRENT (mA) 40 50 3719 G05 4.70 - 50 - 25 50 25 75 0 TEMPERATURE (C) 100 125 3719 G06 Maximum Current Sense Threshold vs Duty Factor 75 80 70 60 Maximum Current Sense Threshold vs Percent of Nominal Output Voltage (Foldback) 50 50 40 30 20 10 25 0 0 20 40 60 DUTY FACTOR (%) 80 100 3719 G08 0 50 100 0 25 75 PERCENT OF NOMINAL OUTPUT VOLTAGE (%) 3719 G09 3719i 5 LTC3719 TYPICAL PERFOR A CE CHARACTERISTICS Maximum Current Sense Threshold vs VRUN/SS (Soft-Start) 80 VSENSE(CM) = 1.6V 80 60 VSENSE (mV) VSENSE (mV) 72 VSENSE (mV) 40 20 64 0 0 1 2 3 VRUN/SS (V) 3719 G10 4 Load Regulation 0.0 FCB = 0V VIN = 15V FIGURE 1 NORMALIZED VOUT (%) -0.1 -0.2 VITH (V) 1.5 ISENSE (A) -0.3 -0.4 0 5 15 10 LOAD CURRENT (A) Maximum Current Sense Threshold vs Temperature 80 1.8 1.6 78 RUN/SS CURRENT (A) VSENSE (mV) 76 74 72 70 -50 -25 50 25 0 75 TEMPERATURE (C) 6 UW 5 20 3719 G13 Maximum Current Sense Threshold vs Sense Common Mode Voltage 90 80 76 70 60 50 40 30 20 10 0 -10 -20 -30 Current Sense Threshold vs ITH Voltage 68 6 60 0 1 COMMON MODE VOLTAGE (V) 2 3719 G11 0 0.5 1 1.5 VITH (V) 2 2.5 3719 G12 VITH vs VRUN/SS (Soft-Start) 2.5 VOSENSE = 0.7V SENSE Pins Total Source Current 100 2.0 50 0 1.0 -50 0.5 25 0 0 1 2 3 VRUN/SS (V) 4 5 6 3719 G14 -100 0 1 VSENSE COMMON MODE VOLTAGE (V) 2 3719 G15 RUN/SS Current vs Temperature Soft-Start Up (Figure 13) VITH 1V/DIV VOUT 1V/DIV VRUN/SS 2V/DIV 1.4 1.2 1.0 0.8 0.6 0.4 0.2 100ms/DIV 3718 G18 100 125 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 3719 G16 3719 G17 3719i LTC3719 TYPICAL PERFOR A CE CHARACTERISTICS Load Step (Figure 13) VIN = 15V, VOUT = 1.25V, SLEW RATE = 30A/s VCC 50mV/DIV VOUT(AC) 20mV/DIV IL1 1A/DIV ICC 4A/DIV FCB = 0V 25s/DIV 3719 G19 Current Sense Pin Input Current vs Temperature -12 CURRENT SENSE INPUT CURRENT (A) VOUT = 1.6V -11 EXTVCC SWITCH RESISTANCE () -10 6 FREQUENCY (kHz) -9 -8 -7 -50 -25 50 25 0 75 TEMPERATURE (C) Undervoltage Lockout vs Temperature 3.50 3.45 3.40 3.35 3.30 3.25 3.20 -50 -25 SHUTDOWN LATCH THRESHOLDS (V) UNDERVOLTAGE LOCKOUT (V) UW 100 3719 G20 Burst Mode Operation (Figure 13) VIN = 15V, VOUT = 1.6V, IL = 200mARMS VOUT(AC) 20mV/DIV IL1 1A/DIV Constant Frequency Mode (Figure 13) VIN = 15V, VOUT = 1.6V, IL = 400mARMS IL2 1A/DIV FCB = OPEN 10s/DIV R9, R21 = 0.01 3719 G25 IL2 1A/DIV FCB = INTVCC 2s/DIV R9, R21 = 0.01 3719 G26 EXTVCC Switch Resistance vs Temperature 10 350 300 8 250 200 150 100 50 0 -50 -25 Oscillator Frequency vs Temperature VPLLFLTR = 5V 4 VPLLFLTR = 0V 2 125 50 25 0 75 TEMPERATURE (C) 100 125 0 - 50 - 25 50 25 75 0 TEMPERATURE (C) 100 125 3719 G21 3719 G22 VRUN/SS Shutdown Latch Thresholds vs Temperature 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 LATCHOFF THRESHOLD LATCH ARMING 50 25 75 0 TEMPERATURE (C) 100 125 3719 G23 3719 G24 3719i 7 LTC3719 PI FU CTIO S RUN/SS (Pin 1): Combination of Soft-Start, Run Control Input and Short-Circuit Detection Timer. A capacitor to ground at this pin sets the ramp time to full current output. Forcing this pin below 0.8V causes the IC to shut down all internal circuitry. All functions are disabled in shutdown. SENSE1+, SENSE2+ (Pins 2,14): The (+) Input to Each Differential Current Comparator. The ITH pin voltage and built-in offsets between SENSE- and SENSE+ pins in conjunction with RSENSE set the current trip threshold. SENSE1-, SENSE2- (Pins 3,13): The (-) Input to the Differential Current Comparators. EAIN (Pin 4): Input to the error amplifier that compares the feedback voltage to the internal 0.6V reference voltage. This pin is normally connected to a resistive divider from the output of the differential amplifier (DIFFOUT). PLLFLTR (Pin 5): The phase-locked loop's lowpass filter is tied to this pin. Alternatively, this pin can be driven with an AC or DC voltage source to vary the frequency of the internal oscillator. Do not apply voltage to this pin prior to application of VIN. PLLIN (Pin 6): External Synchronization Input to Phase Detector. This pin is internally terminated to SGND with 50k. The phase-locked loop will force the rising top gate signal of controller 1 to be synchronized with the rising edge of the PLLIN signal. FCB (Pin 7): Forced Continuous Control Input. This input acts on both output stages and can be used to regulate a secondary winding. Pulling this pin below 0.6V will force continuous synchronous operation. Do not leave this pin floating without a decoupling capacitor. ITH (Pin 8): Error Amplifier Output and Switching Regulator Compensation Point. Both current comparator's thresholds increase with this control voltage. The normal voltage range of this pin is from 0V to 2.4V SGND (Pin 9): Signal Ground. This pin is common to both controllers. Route separately to the PGND pin. VDIFFOUT (Pin 10): Output of a Differential Amplifier. This pin provides true remote output voltage sensing. VDIFFOUT normally drives an external resistive divider that sets the output voltage. VOS-, VOS+ (Pins 11, 12): Inputs to an Operational Amplifier. Internal precision resistors configure it as a differential amplifier whose output is VDIFFOUT. ATTENOUT (Pin 15): Voltage Feedback Signal Resistively Divided According to the VID Programming Code. NO_CPU (Pin 16): Open-Drain Logic Output. NO_CPU is pulled to ground if VID0 to VID3 are all high. VID0-VID4 (Pins 17,18, 19, 20, 21): VID Control Logic Input Pins. VBIAS (Pin 22): Supply Pin for the VID Control Circuit. ATTENIN (Pin 23): The Input to the VID Controlled Resistive Divider. TG2, TG1 (Pins 24, 35): High Current Gate Drives for Top N-Channel MOSFETS. These are the outputs of floating drivers with a voltage swing equal to INTVCC superimposed on the switch node voltage SW. SW2, SW1 (Pins 25, 34): Switch Node Connections to Inductors. Voltage swing at these pins is from a Schottky diode (external) voltage drop below ground to VIN. BOOST2, BOOST1 (Pins 26, 33): Bootstrapped Supplies to the Topside Floating Drivers. External capacitors are connected between the BOOST and SW pins, and Schottky diodes are connected between the BOOST and INTVCC pins. BG2, BG1 (Pins 27, 31): High Current Gate Drives for Bottom N-Channel MOSFETS. Voltage swing at these pins is from ground to INTVCC. PGND (Pin 28): Driver Power Ground. Connect to sources of bottom N-channel MOSFETS and the (-) terminals of CIN. INTVCC (Pin 29): Output of the Internal 5V Linear Low Dropout Regulator and the EXTVCC Switch. The driver and control circuits are powered from this voltage source. Decouple to power ground with a 1F ceramic capacitor placed directly adjacent to the IC and minimum of 4.7F additional tantalum or other low ESR capacitor. EXTVCC (Pin 30): External Power Input to an Internal Switch. This switch closes and supplies INTVCC, bypassing the internal low dropout regulator whenever EXTVCC is higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 7V on this pin and ensure VEXTVCC VINTVCC. 3719i 8 U U U LTC3719 PI FU CTIO S VIN (Pin 32): Main Supply Pin. Should be closely decoupled to the IC's signal ground pin. PGOOD (Pin 36): Open-Drain Logic Output. PGOOD is pulled to ground when the voltage on the EAIN pin is not within 10% of its set point. FU CTIO AL DIAGRA PLLIN fIN 50k RLP PLLFLTR CLP CLK1 OSCILLATOR CLK2 TO SECOND CHANNEL PHASE DET PGOOD - + 0.66V EAIN - 0.55V + + VOS - 40k 40k 0.54V B - VOS + 40k + 40k A1 I1 - + DIFFOUT 3V 0.18A FCB + - VIN 0.60V FCB - EA + OV 4.8V EXTVCC + - 5V LDO REG + - 1.2A SHDN RST 5VFB - 0.86V 5VFB 4.5V - + SLOPE COMP 45k 45k 2.4V VFB 0.60V VREF + 5V INTVCC 6V SGND INTERNAL SUPPLY ATTENIN 10k 5-BIT VID DECODER ATTENOUT TYPICAL ALL VID PINS 40k R1 NO_CPU VID0 VID1 VID2 VID3 VID4 - W U U U U U INTVCC DUPLICATE FOR SECOND CONTROLLER CHANNEL BOOST DB VIN DROP OUT DET S R Q Q TOP BOT FCB TG CB D1 + CIN TOP ON SWITCH LOGIC BOT INTVCC SW BG PGND COUT + VOUT SHDN L I2 INTVCC + 30k SENSE - 30k SENSE 1 3 RSENSE 2 4 ++ - - + EAIN 0.66V CC ITH RUN SOFTSTART CC2 RC RUN/SS CSS VBIAS 3719 FBD 3719i 9 LTC3719 OPERATIO Main Control Loop The LTC3719 uses a constant frequency, current mode step-down architecture with the two output stages operating 180 degrees out of phase. During normal operation, each top MOSFET is turned on when the clock for that channel sets the RS latch, and turned off when the main current comparator, I1, resets the RS latch. The peak inductor current at which I1 resets the RS latch is controlled by the voltage on the ITH pin, which is the output of error amplifier EA. The EAIN pin receives the voltage feedback signal, which is compared to the internal reference voltage by the EA. When the load current increases, it causes a slight decrease in VEAIN relative to the 0.6V reference, which in turn causes the ITH voltage to increase until the average inductor current matches the new load current. After the top MOSFET has turned off, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by current comparator I2, or the beginning of the next cycle. The top MOSFET drivers are biased from floating bootstrap capacitor CB, which normally is recharged during each off cycle through an external diode when the top MOSFET turns off. As VIN decreases to a voltage close to VOUT, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about 500ns every tenth cycle to allow CB to recharge. The main control loop is shut down by pulling the RUN/ SS pin low. Releasing RUN/SS allows an internal 1.2A current source to charge soft-start capacitor CSS. When CSS reaches 1.5V, the main control loop is enabled with the ITH voltage clamped at approximately 30% of its maximum value. As CSS continues to charge, the ITH pin voltage is gradually released allowing normal, full-current operation. Low Current Operation The FCB pin is a multifunction pin providing two functions: 1) to provide regulation for a secondary winding by temporarily forcing continuous PWM operation on both controllers; and 2) select between two modes of low 10 U (Refer to Functional Diagram) current operation. When the FCB pin voltage is below 0.6V, the controller forces continuous PWM current mode operation. In this mode, the top and bottom MOSFETs are alternately turned on to maintain the output voltage independent of direction of inductor current. When the FCB pin is below VINTVCC - 2V but greater than 0.6V, the controller enters Burst Mode operation. Burst Mode operation sets a minimum output current level before inhibiting the top switch and turns off the synchronous MOSFET(s) when the inductor current goes negative. This combination of requirements will, at low currents, force the ITH pin below a voltage threshold that will temporarily inhibit turn-on of both output MOSFETs until the output voltage drops. There is 60mV of hysteresis in the burst comparator B tied to the ITH pin. This hysteresis produces output signals to the MOSFETs that turn them on for several cycles, followed by a variable "sleep" interval depending upon the load current. The resultant output voltage ripple is held to a very small value by having the hysteretic comparator after the error amplifier gain block. Constant Frequency Operation When the FCB pin is tied to INTVCC, Burst Mode operation is disabled and a forced minimum peak output current requirement is removed. This provides constant frequency, discontinuous (preventing reverse inductor current) current operation over the widest possible output current range. This constant frequency operation is not as efficient as Burst Mode operation, but does provide a lower noise, constant frequency operating mode down to approximately 1% of designed maximum output current. Continuous Current (PWM) Operation Tying the FCB pin to ground will force continuous current operation. This is the least efficient operating mode, but may be desirable in certain applications. The output can source or sink current in this mode. When sinking current while in forced continuous operation, current will be forced back into the main power supply potentially boosting the input supply to dangerous voltage levels-- BEWARE! 3719i LTC3719 OPERATIO Frequency Synchronization The phase-locked loop allows the internal oscillator to be synchronized to an external source via the PLLIN pin. The output of the phase detector at the PLLFLTR pin is also the DC frequency control input of the oscillator that operates over a 140kHz to 310kHz range corresponding to a DC voltage input from 0V to 2.4V. When locked, the PLL aligns the turn on of the top MOSFET to the rising edge of the synchronizing signal. When PLLIN is left open, the PLLFLTR pin goes low, forcing the oscillator to minimum frequency. Input capacitance ESR requirements and efficiency losses are substantially reduced because the peak current drawn from the input capacitor is effectively divided by two and power loss is proportional to the RMS current squared. A two stage, single output voltage implementation can reduce input path power loss by 75% and radically reduce the required RMS current rating of the input capacitor(s). INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most of the IC circuitry is derived from INTVCC. When the EXTVCC pin is left open, an internal 5V low dropout regulator supplies INTVCC power. If the EXTVCC pin is taken above 4.8V, the 5V regulator is turned off and an internal switch is turned on connecting EXTVCC to INTVCC. This allows the INTVCC power to be derived from a high efficiency external source such as the output of the regulator itself or a secondary winding, as described in the Applications Information section. An external Schottky diode can be used to minimize the voltage drop from EXTVCC to INTVCC in applications requiring greater than the specified INTVCC current. Voltages up to 7V can be applied to EXTVCC for additional gate drive capability. Differential Amplifier This controller includes a true unity-gain differential amplifier. Sensing both VOUT + and VOUT - benefits regulation in high current applications and/or applications having electrical interconnection losses. The amplifier is a unity-gain stable, 2MHz gain-bandwidth, >120dB openloop gain design. The amplifier has an output slew rate of 5V/s and is capable of driving capacitive loads with an U (Refer to Functional Diagram) output RMS current typically up to 25mA. The amplifier is not capable of sinking current and therefore must be resistively loaded to do so. Output Overvoltage Protection An overvoltage comparator, 0V, guards against transient overshoots (>10%) as well as other more serious conditions that may overvoltage the output. In this case, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. Power Good (PGOOD) The PGOOD pin is connected to the drain of an internal MOSFET. The MOSFET turns on when the output voltage is not within 10% of its nominal output level as determined by the feedback divider. When the output is within 10% of its nominal value, the MOSFET is turned off within 10s and the PGOOD pin should be pulled up by an external resistor to a source of up to 7V. Short-Circuit Detection The RUN/SS capacitor is used initially to limit the inrush current from the input power source. Once the controllers have been given time, as determined by the capacitor on the RUN/SS pin, to charge up the output capacitors and provide full-load current, the RUN/SS capacitor is then used as a short-circuit timeout circuit. If the output voltage falls to less than 70% of its nominal output voltage the RUN/SS capacitor begins discharging assuming that the output is in a severe overcurrent and/or short-circuit condition. If the condition lasts for a long enough period as determined by the size of the RUN/SS capacitor, the controller will be shut down until the RUN/SS pin voltage is recycled. This built-in latchoff can be overidden by providing a current >5A at a compliance of 5V to the RUN/SS pin. This current shortens the soft-start period but also prevents net discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit condition. Foldback current limiting is activated when the output voltage falls below 70% of its nominal level whether or not the short-circuit latchoff circuit is enabled. 3719i 11 LTC3719 APPLICATIO S I FOR ATIO The basic LTC3719 application circuit is shown in Figure 1 on the first page. External component selection begins with the selection of the inductors based on ripple current requirements and continues with the current sensing resistors using the calculated peak inductor current and/or maximum current limit. Next, the power MOSFETs, D1 and D2 are selected. The operating frequency and the inductor are chosen based mainly on the amount of ripple current. Finally, CIN is selected for its ability to handle the input ripple current (that PolyPhase TM operation minimizes) and COUT is chosen with low enough ESR to meet the output ripple voltage and load step specifications (also minimized with PolyPhase). Current mode architecture provides inherent current sharing between output stages. The circuit shown in Figure 1 can be configured for operation up to an input voltage of 28V (limited by the external MOSFETs). Current mode control allows the ability to connect the two output stages to two different input power supply rails. A heavy output load can take some power from each input supply according to the selection of the RSENSE resistors. RSENSE Selection For Output Current RSENSE1,2 are chosen based on the required peak output current. The LTC3719 current comparator has a maximum threshold of 75mV/RSENSE and an input common mode range of SGND to 1.1(INTVCC). The current comparator threshold sets the peak inductor current, yielding a maximum average output current IMAX equal to the peak value less half the peak-to-peak ripple current, IL. Assuming a common input power source for each output stage and allowing a margin for variations in the LTC3719 and external component values yields: RSENSE = 2(50mV/IMAX) Operating Frequency The LTC3719 uses a constant frequency, phase-lockable architecture with the frequency determined by an internal capacitor. This capacitor is charged by a fixed current PLLFLTR PIN VOLTAGE (V) 12 U plus an additional current which is proportional to the voltage applied to the PLLFLTR pin. Refer to PhaseLocked Loop and Frequency Synchronization for additional information. A graph for the voltage applied to the PLLFLTR pin vs frequency is given in Figure 2. As the operating frequency is increased the gate charge losses will be higher, reducing efficiency (see Efficiency Considerations). The maximum switching frequency is approximately 310kHz. 2.5 2.0 1.5 1.0 0.5 0 120 170 220 270 OPERATING FREQUENCY (kHz) 320 3719 F02 W U U Figure 2. Operating Frequency vs VPLLFLTR Inductor Value Calculation and Output Ripple Current The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because MOSFET gate charge and transition losses increase directly with frequency. In addition to this basic tradeoff, the effect of inductor value on ripple current and low current operation must also be considered. The PolyPhase approach reduces both input and output ripple currents while optimizing individual output stages to run at a lower fundamental frequency, enhancing efficiency. PolyPhase is a registered trademark of Linear Technology Corporation. 3719i LTC3719 APPLICATIO S I FOR ATIO The inductor value has a direct effect on ripple current. The inductor ripple current IL per individual section, N, decreases with higher inductance or frequency and increases with higher VIN or VOUT: IL = VOUT VOUT 1- f *L VIN where f is the individual output stage operating frequency. In a 2-phase converter, the net ripple current seen by the output capacitor is much smaller than the individual inductor ripple currents due to ripple cancellation. The details on how to calculate the net output ripple current can be found in Application Note 77. Figure 3 shows the net ripple current seen by the output capacitors for 1- and 2-phase configurations. The output ripple current is plotted for a fixed output voltage as the duty factor is varied between 10% and 90% on the x-axis. The output ripple current is normalized against the inductor ripple current at zero duty factor. The graph can be used in place of tedious calculations, simplifying the design process. Accepting larger values of IL allows the use of low inductances, but can result in higher output voltage ripple. A reasonable starting point for setting ripple current is 1.0 0.9 0.8 0.7 1-PHASE 2-PHASE IO(P-P) 0.6 VO/fL 0.5 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3719 F03 Figure 3. Normalized Output Ripple Current vs Duty Factor [IRMS 0.3 (IO(P-P))] U IL = 0.4(IOUT)/2, where IOUT is the total load current. Remember, the maximum IL occurs at the maximum input voltage. The individual inductor ripple currents are determined by the inductor, input and output voltages. Inductor Core Selection Once the values for L1 and L2 are known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite, molypermalloy, or Kool M(R) cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductor type selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates "hard," which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Molypermalloy (from Magnetics, Inc.) is a very good, low loss core material for toroids, but it is more expensive than ferrite. A reasonable compromise from the same manufacturer is Kool M. Toroids are very space efficient, especially when you can use several layers of wire. Because they lack a bobbin, mounting is more difficult. However, designs for surface mount are available which do not increase the height significantly. Power MOSFET, D1 and D2 Selection Two external power MOSFETs must be selected for each output stage with the LTC3719: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. Kool M is a registered trademark of Magnetics, Inc. 3719i W U U 13 LTC3719 APPLICATIO S I FOR ATIO The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only exception is if low input voltage is expected (VIN < 5V); then, sublogic-level threshold MOSFETs (VGS(TH) < 1V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the "ON" resistance RDS(ON), reverse transfer capacitance CRSS, input voltage and maximum output current. When the LTC3719 is operating in continuous mode the duty factors for the top and bottom MOSFETs of each output stage are given by: Main Switch Duty Cycle = VOUT VIN V -V Synchronous Switch Duty Cycle = IN OUT VIN The MOSFET power dissipations at maximum output current are given by: PMAIN = VOUT IMAX (1 + )RDS(ON) + VIN 2 2 2 I k( VIN ) MAX (CRSS )( f) 2 2 PSYNC = VIN - VOUT IMAX (1 + )RDS(ON) 2 VIN where is the temperature dependency of RDS(ON) and k is a constant inversely related to the gate drive current. Both MOSFETs have I2R losses but the topside N-channel equation includes an additional term for transition losses, 14 U which peak at the highest input voltage. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CRSS actual provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The term (1 + ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs temperature curve, but = 0.005/C can be used as an approximation for low voltage MOSFETs. CRSS is usually specified in the MOSFET characteristics. The constant k = 1.7 can be used to estimate the contributions of the two terms in the main switch dissipation equation. The Schottky diodes, D1 and D2 shown in Figure 1 conduct during the dead-time between the conduction of the two large power MOSFETs. This helps prevent the body diode of the bottom MOSFET from turning on, storing charge during the dead-time, and requiring a reverse recovery period which would reduce efficiency. A 1A to 3A Schottky (depending on output current) diode is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. CIN and COUT Selection In continuous mode, the source current of each top N-channel MOSFET is a square wave of duty cycle VOUT/ VIN. A low ESR input capacitor sized for the maximum RMS current must be used. The details of a closed form equation can be found in Application Note 77. Figure 4 shows the input capacitor ripple current for a 2-phase configuration with the output voltage fixed and input voltage varied. The input ripple current is normalized against the DC output current. The graph can be used in place of tedious calculations. The minimum input ripple 3719i W U U LTC3719 APPLICATIO S I FOR ATIO current can be achieved when the input voltage is twice the output voltage. In the graph of Figure 4, the 2-phase local maximum input RMS capacitor currents are reached when: VOUT 2k - 1 = VIN 4 where k = 1, 2 These worst-case conditions are commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturer's ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. Always consult the capacitor manufacturer if there is any question. It is important to note that the efficiency loss is proportional to the input RMS current squared and therefore a 2-phase implementation results in 75% less power loss when compared to a single phase design. Battery/input protection fuse resistance (if used), PC board trace and connector resistance losses are also reduced by the 0.6 0.5 DC LOAD CURRENT RMS INPUT RIPPLE CURRNET 0.4 0.3 0.2 0.1 0 1-PHASE 2-PHASE 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3719 F04 Figure 4. Normalized RMS Input Ripple Current vs Duty Factor for 1 and 2 Output Stages U reduction of the input ripple current in a 2-phase system. The required amount of input capacitance is further reduced by the factor, 2, due to the effective increase in the frequency of the current pulses. The selection of COUT is driven by the required effective series resistance (ESR). Typically once the ESR requirement has been met, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirements. The steady state output ripple (VOUT) is determined by: W U U 1 VOUT IRIPPLE ESR + 16 fCOUT Where f = operating frequency of each stage, COUT = output capacitance and IRIPPLE = combined inductor ripple currents. The output ripple varies with input voltage since IL is a function of input voltage. The output ripple will be less than 50mV at max VIN with IL = 0.4IOUT(MAX)/2 assuming: COUT required ESR < 4(RSENSE) and COUT > 1/(16f)(RSENSE) The emergence of very low ESR capacitors in small, surface mount packages makes very physically small implementations possible. The ability to externally compensate the switching regulator loop using the I TH pin(OPTI-LOOP compensation) allows a much wider selection of output capacitor types. OPTI-LOOP compensation effectively removes constraints on output capacitor ESR. The impedance characteristics of each capacitor type are significantly different than an ideal capacitor and therefore require accurate modeling or bench evaluation during design. Manufacturers such as Nichicon, United Chemicon and Sanyo should be considered for high performance through-hole capacitors. The OS-CON semiconductor dielectric capacitor available from Sanyo and the Panasonic SP surface mount types have the lowest (ESR)(size) product of any aluminum electrolytic at a somewhat 3719i 15 LTC3719 APPLICATIO S I FOR ATIO higher price. An additional ceramic capacitor in parallel with OS-CON type capacitors is recommended to reduce the inductance effects. In surface mount applications, multiple capacitors may have to be paralleled to meet the ESR or RMS current handling requirements of the application. Aluminum electrolytic and dry tantalum capacitors are both available in surface mount configurations. New special polymer surface mount capacitors offer very low ESR also but have much lower capacitive density per unit volume. In the case of tantalum, it is critical that the capacitors are surge tested for use in switching power supplies. Several excellent choices are the AVX TPS, AVX TPSV or the KEMET T510 series of surface mount tantalums, available in case heights ranging from 2mm to 4mm. Other capacitor types include Sanyo OS-CON, POSCAPs, Panasonic SP caps, Nichicon PL series and Sprague 595D series. Consult the manufacturer for other specific recommendations. A combination of capacitors will often result in maximizing performance and minimizing overall cost and size. INTVCC Regulator An internal P-channel low dropout regulator produces 5V at the INTVCC pin from the VIN supply pin. The INTVCC regulator powers the drivers and internal circuitry of the LTC3719. The INTVCC pin regulator can supply up to 50mA peak and must be bypassed to power ground with a minimum of 4.7F tantalum or electrolytic capacitor. An additional 1F ceramic capacitor placed very close to the IC is recommended due to the extremely high instantaneous currents required by the MOSFET gate drivers. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3719 to be exceeded. The supply current is dominated by the gate charge supply current, in addition to the current drawn from the differential amplifier output. The gate charge is dependent on operating frequency as discussed in the Efficiency Considerations section. The supply current can 16 U either be supplied by the internal 5V regulator or via the EXTVCC pin. When the voltage applied to the EXTVCC pin is less than 4.7V, all of the INTVCC load current is supplied by the internal 5V linear regulator. Power dissipation for the IC is higher in this case by (IIN)(VIN - INTVCC) and efficiency is lowered. The junction temperature can be estimated by using the equations given in Note 1 of the Electrical Characteristics. For example, the LTC3719 VIN current is limited to less than 24mA from a 24V supply: TJ = 70C + (24mA)(24V)(85C/W) = 119C Use of the EXTVCC pin reduces the junction temperature to: TJ = 70C + (24mA)(5V)(85C/W) = 80.2C The input supply current should be measured while the controller is operating in continuous mode at maximum VIN and the power dissipation calculated in order to prevent the maximum junction temperature from being exceeded. EXTVCC Connection The LTC3719 contains an internal P-channel MOSFET switch connected between the EXTVCC and INTVCC pins. When the voltage applied to EXTVCC rises above 4.7V, the internal regulator is turned off and an internal switch closes, connecting the EXTVCC pin to the INTVCC pin thereby supplying internal and MOSFET gate driving power to the IC. The switch remains closed as long as the voltage applied to EXTVCC remains above 4.5V. This allows the MOSFET driver and control power to be derived from the output during normal operation (4.7V < VEXTVCC < 7V) and from the internal regulator when the output is out of regulation (start-up, short-circuit). Do not apply greater than 7V to the EXTVCC pin and ensure that EXTVCC < VIN + 0.3V when using the application circuits shown. If an external voltage source is applied to the EXTVCC pin when the VIN supply is not present, a diode can be placed in series with the LTC3719's VIN pin and a Schottky diode between the EXTVCC and the VIN pin, to prevent current from backfeeding VIN. 3719i W U U LTC3719 APPLICATIO S I FOR ATIO Significant efficiency gains can be realized by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be scaled by the ratio: (Duty Factor)/(Efficiency). For 5V regulators this means connecting the EXTVCC pin directly to VOUT. However, for 3.3V and other lower voltage regulators, additional supply circuitry is required to derive INTVCC power from the output. The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 5V regulator resulting in a significant efficiency penalty at high input voltages. 2. EXTVCC connected directly to VOUT. This is the normal connection for a 5V regulator and provides the highest efficiency. 3. EXTVCC connected to an external supply. If an external supply is available in the 5V to 7V range, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. 4. EXTVCC connected to an output-derived boost network. For 3.3V and other low voltage regulators, efficiency gains can still be realized by connecting EXTVCC to an outputderived voltage which has been boosted to greater than OPTIONAL EXTVCC CONNECTION 5V < VSEC < 7V VIN TG1 LTC3719 EXTVCC SW1 R6 FCB R5 PGND 3716 F05a + CIN VIN VIN 1N4148 VSEC N-CH 1 RSENSE 2 T1 3 4 BG1 N-CH Figure 5a. Secondary Output Loop with EXTVCC Connection U 4.7V but less than 7V. This can be done with either the inductive boost winding as shown in Figure 5a or the capacitive charge pump shown in Figure 5b. The charge pump has the advantage of simple magnetics. Topside MOSFET Driver Supply (CB,DB) (Refer to Functional Diagram) External bootstrap capacitors CB1 and CB2 connected to the BOOST1 and BOOST2 pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though diode DB from INTVCC when the SW pin is low. When the topside MOSFET turns on, the driver places the CB voltage across the gatesource of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN and the BOOST pin rises to VIN + VINTVCC. The value of the boost capacitor CB needs to be 30 to 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of DB must be greater than VIN(MAX). The final arbiter when defining the best gate drive amplitude level will be the input supply current. If a change is made that decreases input current, the efficiency has improved. If the input current does not change then the efficiency has not changed either. + CIN BAT85 0.22F BAT85 VIN W U U + TG1 LTC3719 N-CH + 1F EXTVCC VN2222LL 1 RSENSE 2 L1 3 4 BAT85 VOUT COUT SW1 VOUT + + COUT BG1 N-CH PGND 3716 F05b Figure 5b. Capacitive Charge Pump for EXTVCC 3719i 17 LTC3719 APPLICATIO S I FOR ATIO Output Voltage The LTC3719 has a true remote voltage sense capablity. The sensing connections should be returned from the load back to the differential amplifier's inputs through a common, tightly coupled pair of PC traces. The differential amplifier corrects for DC drops in both the power and ground paths. The differential amplifier output signal is divided down and compared with the internal precision 0.6V voltage reference by the error amplifier. Output Voltage Programming The output voltage is digitally programmed as defined in Table 1 using the VID0 to VID4 logic input pins. The VID logic inputs program a precision, 0.25% internal feedback resistive divider. The LTC3719 has an output voltage range of 0.8V to 1.55V in 25mV steps. Between the ATTENOUT pin and ground is a variable resistor, R1, whose value is controlled by the five VID input pins (VID0 to VID4). Another resistor, R2, between the ATTENIN and the ATTENOUT pins completes the resistive divider. The output voltage is thus set by the ratio of (R1 + R2) to R1. Each VID digital input is pulled up by a 40k resistor in series with a diode from VBIAS. Therefore, it must be grounded to get a digital low input, and can be either floated or connected to VBIAS to get a digital high input. The series diode is used to prevent the digital inputs from being damaged or clamped if they are driven higher than VBIAS. The digital inputs accept CMOS voltage levels. VBIAS is the supply voltage for the VID section. It is normally connected to INTVCC but can be driven from other sources. If it is driven from another source, that source must be in the range of 2.7V to 5.5V and must be alive prior to enabling the LTC3719. 18 U Table 1. VID Output Voltage Programming CODE 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 VID4 GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Float Float Float Float Float Float Float Float Float Float Float Float Float Float Float Float VID3 GND GND GND GND GND GND GND GND Float Float Float Float Float Float Float Float GND GND GND GND GND GND GND GND Float Float Float Float Float Float Float Float VID2 GND GND GND GND Float Float Float Float GND GND GND GND Float Float Float Float GND GND GND GND Float Float Float Float GND GND GND GND Float Float Float Float VID1 GND GND Float Float GND GND Float Float GND GND Float Float GND GND Float Float GND GND Float Float GND GND Float Float GND GND Float Float GND GND Float Float VID0 GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float GND Float OUTPUT 1.550 1.525 1.500 1.475 1.450 1.425 1.400 1.375 1.350 1.325 1.300 1.275 1.250 1.225 1.200 1.175 1.150 1.125 1.100 1.075 1.050 1.025 1.000 0.975 0.950 0.925 0.900 0.875 0.850 0.825 0.800 Shutdown 3719i W U U LTC3719 APPLICATIO S I FOR ATIO Soft-Start/Run Function The RUN/SS pin provides three functions: 1) Run/Shutdown, 2) soft-start and 3) a defeatable short-circuit latchoff timer. Soft-start reduces the input power sources' surge currents by gradually increasing the controller's current limit ITH(MAX). The latchoff timer prevents very short, extreme load transients from tripping the overcurrent latch. A small pull-up current (>5A) supplied to the RUN/ SS pin will prevent the overcurrent latch from operating. The following explanation describes how the functions operate. An internal 1.2A current source charges up the soft-start capacitor, CSS. When the voltage on RUN/SS reaches 1.5V, the controller is permitted to start operating. As the voltage on RUN/SS increases from 1.5V to 3.0V, the internal current limit is increased from 25mV/RSENSE to 75mV/RSENSE. The output current limit ramps up slowly, taking an additional 1.4s/F to reach full current. The output current thus ramps up slowly, reducing the starting surge current required from the input power supply. If RUN/SS has been pulled all the way to ground there is a delay before starting of approximately: tDELAY = 1.5V CSS = (1.25s /F ) CSS 1.2A The time for the output current to ramp up is then: tIRAMP = 3V - 1.5V CSS = (1.25s /F ) CSS 1.2A By pulling the RUN/SS pin below 0.8V the LTC3719 is put into low current shutdown (IQ < 40A). The RUN/SS pins can be driven directly from logic as shown in Figure 6. Diode D1 in Figure 6 reduces the start delay but allows CSS to ramp up slowly providing the soft-start function. The RUN/SS pin has an internal 6V zener clamp (see Functional Diagram). U VIN 3.3V OR 5V D1 RUN/SS RSS* D1* CSS CSS INTVCC RSS* RUN/SS *OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF 3719 F06 W U U Figure 6. RUN/SS Pin Interfacing Fault Conditions: Overcurrent Latchoff The RUN/SS pin also provides the ability to latch off the controllers when an overcurrent condition is detected. The RUN/SS capacitor, CSS, is used initially to limit the inrush current of both controllers. After the controllers have been started and been given adequate time to charge up the output capacitors and provide full load current, the RUN/ SS capacitor is used for a short-circuit timer. If the output voltage falls to less than 70% of its nominal value after CSS reaches 4.1V, CSS begins discharging on the assumption that the output is in an overcurrent condition. If the condition lasts for a long enough period as determined by the size of the CSS, the controller will be shut down until the RUN/SS pin voltage is recycled. If the overload occurs during start-up, the time can be approximated by: tLO1 (CSS * 0.6V)/(1.2A) = 5 * 105 (CSS) If the overload occurs after start-up, the voltage on CSS will continue charging and will provide additional time before latching off: tLO2 (CSS * 3V)/(1.2A) = 2.5 * 106 (CSS) This built-in overcurrent latchoff can be overridden by providing a pull-up resistor, RSS, to the RUN/SS pin as shown in Figure 6. This resistance shortens the soft-start period and prevents the discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit 3719i 19 LTC3719 APPLICATIO S I FOR ATIO condition. When deriving the 5A current from VIN as in the figure, current latchoff is always defeated. The diode connecting this pull-up resistor to INTVCC, as in Figure 6, eliminates any extra supply current during shutdown while eliminating the INTVCC loading from preventing controller start-up. Why should you defeat current latchoff? During the prototyping stage of a design, there may be a problem with noise pickup or poor layout causing the protection circuit to latch off the controller. Defeating this feature allows troubleshooting of the circuit and PC layout. The internal short-circuit and foldback current limiting still remains active, thereby protecting the power supply system from failure. A decision can be made after the design is complete whether to rely solely on foldback current limiting or to enable the latchoff feature by removing the pull-up resistor. The value of the soft-start capacitor CSS may need to be scaled with output voltage, output capacitance and load current characteristics. The minimum soft-start capacitance is given by: CSS > (COUT )(VOUT)(10-4)(RSENSE) The minimum recommended soft-start capacitor of CSS = 0.1F will be sufficient for most applications. Phase-Locked Loop and Frequency Synchronization The LTC3719 has a phase-locked loop comprised of an internal voltage controlled oscillator and phase detector. This allows the top MOSFET turn-on to be locked to the rising edge of an external source. The frequency range of the voltage controlled oscillator is 50% around the center frequency fO. A voltage applied to the PLLFLTR pin of 1.2V corresponds to a frequency of approximately 220kHz. The nominal operating frequency range of the LTC3719 is 140kHz to 310kHz. The phase detector used is an edge sensitive digital type which provides zero degrees phase shift between the 20 U external and internal oscillators. This type of phase detector will not lock up on input frequencies close to the harmonics of the VCO center frequency. The PLL hold-in range, fH, is equal to the capture range, fC: fH = fC = 0.5 fO (150kHz-300kHz) The output of the phase detector is a complementary pair of current sources charging or discharging the external filter network on the PLLFLTR pin. A simplified block diagram is shown in Figure 7. 2.4V W U U PHASE DETECTOR EXTERNAL OSC RLP 10k CLP PLLFLTR PLLIN 50k DIGITAL PHASE/ FREQUENCY DETECTOR OSC 3719 F07 Figure 7. Phase-Locked Loop Block Diagram If the external frequency (fPLLIN) is greater than the oscillator frequency f0SC, current is sourced continuously, pulling up the PLLFLTR pin. When the external frequency is less than f0SC, current is sunk continuously, pulling down the PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. Thus the voltage on the PLLFLTR pin is adjusted until the phase and frequency of the external and internal oscillators are identical. At this stable operating point the phase comparator output is open and the filter capacitor CLP holds the voltage. The LTC3719 PLLIN pin must be driven from a low impedance source such as a logic gate located close to the pin. 3719i LTC3719 APPLICATIO S I FOR ATIO The loop filter components (CLP, RLP) smooth out the current pulses from the phase detector and provide a stable input to the voltage controlled oscillator. The filter components CLP and RLP determine how fast the loop acquires lock. Typically RLP =10k and CLP is 0.01F to 0.1F. Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3719 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN) < VOUT VIN ( f) If the duty cycle falls below what can be accommodated by the minimum on-time, the LTC3719 will begin to skip cycles resulting in variable frequency operation. The output voltage will continue to be regulated, but the ripple current and ripple voltage will increase. The minimum on-time for the LTC3719 is generally less than 200ns. However, as the peak sense voltage decreases, the minimum on-time gradually increases. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger ripple current and voltage ripple. If an application can operate close to the minimum on-time limit, an inductor must be chosen that has a low enough inductance to provide sufficient ripple amplitude to meet the minimum on-time requirement. As a general rule, keep the inductor ripple current of each phase equal to or greater than 15% of IOUT(MAX) at VIN(MAX). U FCB Pin Operation The FCB pin can be used to regulate a secondary winding or as a logic level input. Continuous operation is forced when the FCB pin drops below 0.6V. During continuous mode, current flows continuously in the transformer primary. The secondary winding(s) supply current only when the bottom, synchronous switch is on. When primary load currents are low and/or the VIN/VOUT ratio is low, the synchronous switch may not be on for a sufficient amount of time to transfer power from the output capacitor to the secondary load. Forced continuous operation will support secondary windings providing there is sufficient synchronous switch duty factor. Thus, the FCB input pin removes the requirement that power must be drawn from the inductor primary in order to extract power from the auxiliary winding(s). With the loop in continuous mode, the auxiliary output(s) may nominally be loaded without regard to the primary output load. The secondary output voltage VSEC is normally set as shown in Figure 5a by the turns ratio N of the transformer: VSEC (N + 1) VOUT However, if the controller goes into Burst Mode operation and halts switching due to a light primary load current, then VSEC will droop. An external resistive divider from VSEC to the FCB pin sets a minimum voltage VSEC(MIN): R6 VSEC(MIN) 0.6 V 1 + R5 where R5 and R6 are shown in Figure 5a. If VSEC drops below this level, the FCB voltage forces temporary continuous switching operation until VSEC is again above its minimum. In order to prevent erratic operation if no external connections are made to the FCB pin, the FCB pin has a 0.18A internal current source pulling the pin high. Include this current when choosing resistor values R5 and R6. 3719i W U U 21 LTC3719 APPLICATIO S I FOR ATIO Table 2 FCB Pin 0V to 0.55V 0.65V < VFCB < 4.3V (typ) Condition The following table summarizes the possible states available on the FCB pin: Forced Continuous (Current Reversal Allowed--Burst Inhibited) Minimum Peak Current Induces Burst Mode Operation No Current Reversal Allowed Regulating a Secondary Winding Burst Mode Operation Disabled Constant Frequency Mode Enabled No Current Reversal Allowed No Minimum Peak Current Feedback Resistors >4.8V Active Voltage Positioning Active voltage positioning can be used to minimize peakto-peak output voltage excursion under worst-case transient loading conditions. The open-loop DC gain of the control loop is reduced depending upon the maximum load step specifications. Active voltage positioning can easily be added to the LTC3719 by loading the ITH pin with a resistive divider having a Thevenin equivalent voltage source equal to the midpoint operating voltage of the error amplifier, or 1.2V (see Figure 8). INTVCC RT2 ITH RT1 RC CC 3719 F08 LTC3719 Figure 8. Active Voltage Positioning Applied to the LTC3719 The resistive load reduces the DC loop gain while maintaining the linear control range of the error amplifier. The worst-case peak-to-peak output voltage deviation due to transient loading can theoretically be reduced to half or alternatively the amount of output capacitance can be reduced for a particular application. A complete 22 U explanation is included in Design Solutions 10 or the LTC1736 data sheet. (See www.linear-tech.com) Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3719 circuits: 1) I2R losses, 2) Topside MOSFET transition losses, 3) INTVCC regulator current and 4) LTC3719 VIN current (including loading on the differential amplifier output). 1) I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is "chopped" between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON) = 10m, RL = 10m, and RSENSE = 5m, then the total resistance is 25m. This results in losses ranging from 2% to 8% as the output current increases from 3A to 15A per output stage for a 5V output, or a 3% to 12% loss per output stage for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 3719i W U U LTC3719 APPLICATIO S I FOR ATIO 2) Transition losses apply only to the topside MOSFET(s), and are significant only when operating at high input voltages (typically 12V or greater). Transition losses can be estimated from: IO(MAX) Transition Loss = (1.7)VIN2 CRSS f 2 3) INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = (QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. Supplying INTVCC power through the EXTVCC switch input from an output-derived source will scale the VIN current required for the driver and control circuits by the ratio (Duty Factor)/(Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 3mA of VIN current. This reduces the mid-current loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 4) The VIN current has two components: the first is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents; the second is the current drawn from the differential amplifier output. VIN current typically results in a small (<0.1%) loss. Other "hidden" losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these "system" level losses in the design of a system. The internal battery and input fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and a very low ESR at the switching frequency. A 50W supply will typically U require a minimum of 200F to 300F of output capacitance having a maximum of 10m to 20m of ESR. The LTC3719 2-phase architecture typically halves the input and output capacitance requirements over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD(ESR), where ESR is the effective series resistance of COUT (ILOAD) also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. The availability of the ITH pin not only allows optimization of control loop behavior but also provides a DC coupled and AC filtered closed loop response test point. The DC step, rise time, and settling at this test point truly reflects the closed loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in the Figure 1 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.2 to 5 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be decided upon first because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of <2s will 3719i W U U 23 LTC3719 APPLICATIO S I FOR ATIO produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the Ith pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. Design Example As a design example, assume VIN = 5V (nominal), VIN = 5.5V (max), VOUT = 1.2V, IMAX = 20A, TA = 70C and f = 300kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the FREQSET pin to the INTVCC pin for 300kHz operation. The minimum inductance for 30% ripple current is: L VOUT VOUT 1- f( L) VIN 1.2V 1.2V 1- (300kHz)(30%)(10A) 5.5V 1.04H A 1H inductor will produce 31% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 11.5A. The minimum on-time occurs at maximum VIN: tON(MIN) = VOUT 1.2V = = 0.73s VIN f (5.5V )(300kHz) 24 U The RSENSE resistors value can be calculated by using the maximum current sense voltage specification with some accomodation for tolerances: RSENSE = 50mV 0.004 11.5A The power dissipation on the topside MOSFET can be easily estimated. Using a Siliconix Si4420DY for example; RDS(ON) = 0.013, CRSS = 300pF. At maximum input voltage with TJ (estimated) = 110C at an elevated ambient temperature: PMAIN = 1.2V (10)2 1+ (0.005)(110C - 25C) 5.5V W UU [ ] (300kHz) = 0.45W 0.013 + 1.7(5.5V ) (10 A )(300pF ) 2 The worst-case power disipated by the synchronous MOSFET under normal operating conditions at elevated ambient temperature and estimated 50C junction temperature rise is: PSYNC = 5.5V - 1.2V 2 2(10 A ) (1.48)(0.013) 5.5V = 1.5W A short-circuit to ground will result in a folded back current of about: ISC = 25mV 1 200ns(5.5V ) + = 6.8 A 0.004 2 1H The worst-case power disipated by the synchronous MOSFET under short-circuit conditions at elevated ambient temperature and estimated 50C junction temperature rise is: PSYNC = 5.5V - 1.2V (6.8A)2 (1.48)(0.013) 5.5V = 696mW 3719i LTC3719 APPLICATIO S I FOR ATIO which is less than normal, full-load conditions. Incidentally, since the load no longer dissipates power in the shorted condition, total system power dissipation is decreased by over 99%. The duty factor for this application is: DF = VO 1.2V = = 0.24 VIN 5V Using Figure 4, the RMS ripple current will be: IINRMS = (20A)(0.25) = 5ARMS An input capacitor(s) with a 5ARMS ripple current rating is required. The output capacitor ripple current is calculated by using the inductor ripple already calculated for each inductor and multiplying by the factor obtained from Figure 3 along with the calculated duty factor. The output ripple in continuous mode will be highest at the maximum input voltage since the duty factor is < 50%. The maximum output current ripple is: VOUT (0.5) at 24% D F fL 1.2V ICOUTMAX = 0.5 (300kHz)(1.0H) ICOUT = VOUTRIPPLE = 20m(2AP-P ) = 40mVP-P PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3719. Check the following in your layout: 1) Are the signal and power grounds separate? The signal ground traces should return to Pin 9 first. Connect Pin 9 to Pin 28 through a wide and straight trace. Then the signal ground joins the power ground plane beside Pin 28. It is recommended that the Pin 28 return to the (-) plates of CIN. = 2AP-P U 2) Does the LTC3719 VOS+ pin connect to the point of load? Does the LTC3719 VOS- pin connect to the load return? 3) Are the SENSE - and SENSE + leads routed together with minimum PC trace spacing? The filter capacitors between SENSE + and SENSE - pin pairs should be as close as possible to the LTC3719. Ensure accurate current sensing with Kelvin connections at the current sense resistor. See Figure 9. PADS OF SENSE RESISTOR TRACE TO INDUCTOR TRACE TO OUTPUT CAP (+) 3719 F09 W U U SENSE + SENSE - Figure 9. Proper Current Sense Connections 4) Does the (+) plate of CIN connect to the drains of the topside MOSFETs as closely as possible? This capacitor provides the AC current to the MOSFETs. Keep the input current path formed by the input capacitor, top and bottom MOSFETs, and the Schottky diode on the same side of the PC board in a tight loop to minimize conducted and radiated EMI. 5) Is the INTVCC 1F ceramic decoupling capacitor connected closely between INTVCC and the PGND pin? This capacitor carries the MOSFET driver peak currents. A small value is recommended to allow placement immediately adjacent to the IC. 6) Keep the switching nodes, SW1 (SW2), away from sensitive small-signal nodes. Ideally the switch nodes should be placed at the furthest point from the LTC3719. 7) Use a low impedance source such as a logic gate to drive the PLLIN pin and keep the lead as short as possible. 3719i 25 LTC3719 APPLICATIO S I FOR ATIO The diagram in Figure 10 illustrates all branch currents in a 2-phase switching regulator. It becomes very clear after studying the current waveforms why it is critical to keep the high-switching-current paths to a small physical size. High electric and magnetic fields will radiate from these "loops" just as radio stations transmit signals. The output capacitor ground should return to the negative terminal of the input capacitor and not share a common ground path with any switched current paths. The left half of the circuit gives rise to the "noise" generated by a switching regulator. The ground terminations of the sychronous MOSFETs and Schottky diodes should return to the negative plate(s) SW1 D1 VIN RIN CIN + SW2 BOLD LINES INDICATE HIGH, SWITCHING CURRENT LINES. KEEP LINES TO A MINIMUM LENGTH. D2 Figure 10. Instantaneous Current Path Flow in a Multiple Phase Switching Regulator 26 U of the input capacitor(s) with a short isolated PC trace since very high switched currents are present. A separate isolated path from the negative plate(s) of the input capacitor(s) should be used to tie in the IC power ground pin (PGND) and the signal ground pin (SGND). This technique keeps inherent signals generated by high current pulses from taking alternate current paths that have finite impedances during the total period of the switching regulator. External OPTI-LOOP compensation allows overcompensation for PC layouts which are not optimized but this is not the recommended design procedure. L1 RSENSE1 VOUT COUT RL W U U + L2 RSENSE2 3719 F10 3719i LTC3719 APPLICATIO S I FOR ATIO Simplified Visual Explanation of How a 2-Phase Controller Reduces Both Input and Output RMS Ripple Current A multiphase power supply significantly reduces the amount of ripple current in both the input and output capacitors. The RMS input ripple current is divided by, and the effective ripple frequency is multiplied up by the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by, and the effective ripple frequency is increased by the number of phases used. Figure 11 graphically illustrates the principle. The worst-case RMS ripple current for a single stage design peaks at an input voltage of twice the output voltage. The worst-case RMS ripple current for a two stage design results in peak outputs of 1/4 and 3/4 of input voltage. When the RMS current is calculated, higher effective duty factor results and the peak current levels are divided as long as the currents in each stage are balanced. Refer to Application Note 19 for a detailed description of how to calculate RMS current for the single stage switching regulator. Figures 3 and 4 illustrate how the input and output currents are reduced by using an additional phase. The input current peaks drop in half and the frequency is doubled for this 2-phase converter. The input capacity SINGLE PHASE SW V SW1 V SW2 V ICIN IL1 ICOUT IL2 ICIN ICOUT RIPPLE 3719 F11 Figure 11. Single and 2-Phase Current Waveforms U requirement is thus reduced theoretically by a factor of four! Ceramic input capacitors with their unbeatably low ESR characteristics can be used. Figure 4 illustrates the RMS input current drawn from the input capacitance vs the duty cycle as determined by the ratio of input and output voltage. The peak input RMS current level of the single phase system is reduced by 50% in a 2-phase solution due to the current splitting between the two stages. An interesting result of the 2-phase solution is that the VIN which produces worst-case ripple current for the input capacitor, VOUT = VIN/2, in the single phase design produces zero input current ripple in the 2-phase design. The output ripple current is reduced significantly when compared to the single phase solution using the same inductance value because the VOUT/L discharge current term from the stage that has its bottom MOSFET on subtracts current from the (VIN - VOUT)/L charging current resulting from the stage which has its top MOSFET on. The output ripple current is: W U U IRIPPLE = 2VOUT 1 - 2D (1 - D) fL 1 - 2D + 1 where D is duty factor. DUAL PHASE 3719i 27 LTC3719 APPLICATIO S I FOR ATIO The input and output ripple frequency is increased by the number of stages used, reducing the output capacity requirements. When VIN is approximately equal to 2(VOUT) as illustrated in Figures 3 and 4, very low input and output ripple currents result. 28 U Figure 12 shows a typical application using LTC3719 to power the AMD CPU core. The input can vary from 7V to 24V, the output voltage can be programmed from 0.8V to 1.55V with a maximum current of 45A. This power supply receives three input signals to generate different output voltage offsets based on the operation conditions. 3719i W U U PWRGD ENABLE C3 1nF LTC3719 1 RUN/SS PGOOD TG1 Q1 123 C7 0.1F 5678 1 C8 0.47F INTVCC C11 2.2F C12 10F 5678 Q3 C15 0.47F 123 1 0.002 2 3 C16 0.47F 4 5678 Q4 R12 10 123 10 10 C18 0.1F D4 MBRS340T3 L2 1H R7 R8 50 R9 50 COREFB_H COUT1 GND C13 0.47F Q2 2 D2 MBRS340T3 123 C5 0.47F R5 4 0.002 3 L1 1H GND SW1 BOOST1 VIN BG1 EXTVCC INTVCC PGND BG2 BOOST2 SW2 TG2 ATTENIN VBIAS VID4 VID3 VID2 19 20 21 22 23 24 25 26 27 28 29 30 31 D3 BAT54A 32 33 34 35 10 10 CIN1 5678 C2 0.47F SENSE1+ SENSE1- EAIN PLLFLTR PLLIN FCB ITH SGND VDIFFOUT VOS- VOS+ SENSE2 - SENSE2 + ATTENOUT NO_CPU VID0 VID1 36 12VIN 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 R1 10 RUN/SS D1 BAT54 C1 0.1F C4 0.01F R4 10k C6 1nF R23 OPT CLK1 C9 2200pF R6 1.5k + + C10 220pF VDD_CORE+ C14 470pF INTVCC Q9 (OPT) 2N7002 C17 1nF VID0 VID1 VID2 VID3 VID4 CIN1: EIGHT 10F 16V CERAMIC CAPACITORS COUT1: TEN 22F 6.3V CERAMIC CAPACITORS L1 TO L4: SUMIDA CEPH125-1R0MC-H Q1, Q3, Q5, Q7: TWO IRF7811W OR TWO Si7448DP Q2, Q4, Q6, Q8: THREE IRF7822 OR THREE Si7448DP COREFB_L RUN/SS RUN/SS CLKOUT TG1 SW1 BOOST1 VIN BG1 EXTVCC INTVCC PGND BG2 BOOST2 SW2 TG2 AMPMD 15 16 123 17 18 19 20 21 C27 10F C26 2.2F 22 23 D6 BAT54A 5678 Q7 C29 0.47F 123 5678 Q8 24 C23 0.1F 25 C22 0.47F 26 27 SENSE1+ SENSE1- EAIN PLLFLTR PLLIN PHASMD ITH SGND VDIFFOUT VOS- VOS+ SENSE2 - SENSE2 + 2 3 4 5 6 7 8 9 10 11 12 13 14 C20 1nF LTC1629-6 1 28 CLK1 R14 10 5678 Q5 123 C19 0.47F L3 1H 5678 Q6 123 C28 0.47F L4 1H D7 MBRS340T3 3 R18 1 0.002 2 4 C30 0.47F 10 10 3719 F12 C21 27pF 10 10 R17 4 0.002 3 1 2 D5 MBRS340T3 C24 0.47F SYNC C25 27pF + R19 2.7k C31 0.1F R20 10k C32 1nF LTC3719 29 3719i Figure 12. 4-Phase 12V Input, 0.8V to 1.55V/80A Max Power Supply for Server Applications U TYPICAL APPLICATIO R24 OPT LTC3719 TYPICAL APPLICATIO EAIN PLLFLTR PLLIN BG1 EXTVCC INTVCC PGND BG2 BOOST2 SW2 TG2 ATTENIN VBIAS VID4 VID3 VID2 19 20 21 C18 0.1F 22 23 R12 10 24 D4 UPS840 25 3 5678 Q4 Si7448DP 1 2 3 x3 26 1 C15 0.47F 27 L2 0.8H R7 0.002 2 4 C16 0.47F 28 5678 Q3 Si7448DP 1 2 3 x2 C13 0.47F 29 C12 10F C11 2.2F 30 INTVCC FCB ITH SGND VDIFFOUT 31 D3 BAT54A 2 C8 0.47F 1 D2 UPS840 5678 Q2 Si7448DP 1 2 3 x3 VIN 32 C7 1F 4 3 BOOST1 C5 0.47F R5 0.002 5 6 7 8 9 10 11 VOS- 12 VOS+ 13 SENSE2 - SENSE2 + ATTENOUT NO_CPU VID0 VID1 14 15 16 17 18 R23 48.7k CLK1 CIN1: SIX 10F 16V CERAMIC CAPACITORS COUT1: TEN 22F 6.3V CERAMIC CAPACITORS L1, L2: SUMIDA CEP125-1R0MC-H C9 4.7nF R6 2.2k + C10 220pF + COUT1 R8 50 R9 50 VDD_CORE+ GND R24 107k C14 470pF INTVCC COREFB_H 10 10 Q9 (OPT) 2N7002 C17 1nF VID0 VID1 VID2 VID3 VID4 COREFB_L Figure 13. 2-Phase 12V Input, 0.8V to 1.55V/45A Max Power Supply for AMD Hammer CPUs with Active Voltage Positioning (AVP) U 30 C3 1nF LTC3719 1 RUN/SS SENSE1 SENSE1- SW1 33 L1 0.8H 34 + PWRGD ENABLE 36 35 10 10 CIN1 C2 0.47F R1 10 RUN/SS D1 BAT54 PGOOD TG1 5678 Q1 Si7448DP 1 2 3 x2 2 3 4 C1 0.1F 12VIN GND 3719i LTC3719 PACKAGE DESCRIPTIO U G Package 36-Lead Plastic SSOP (5.3mm) (Reference LTC DWG # 05-08-1640) 12.67 - 12.93* (.499 - .509) 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 7.65 - 7.90 (.301 - .311) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5.20 - 5.38** (.205 - .212) 1.73 - 1.99 (.068 - .078) 0 - 8 .65 (.0256) BSC .25 - .38 (.010 - .015) .05 - .21 (.002 - .008) G36 SSOP 0501 .13 - .22 (.005 - .009) .55 - .95 (.022 - .037) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED .152mm (.006") PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE 3719i 31 LTC3719 RELATED PARTS PART NUMBER LTC1436A-PLL LTC1438/LTC1439 LTC1438-ADJ LTC1538-AUX LTC1539 LTC1628/LTC1628-PG LTC1629/LTC1629-PG LTC1702/LTC1703 LTC1708-PG DESCRIPTION High Efficiency Low Noise Synchronous Step-Down Switching Regulator Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulators Dual Synchronous Controller with Auxiliary Regulator Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator PolyPhase High Efficiency Controller Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulators Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator with 5-Bit VID and Power Good Indication LTC1709-7 2-Phase High Efficiency Controller with 5-Bit Mobile VID and Power Good Indication (0.9V VOUT 2V) LTC1709-8/LTC1709-9 2-Phase High Efficiency Controller with 5-Bit VID and Power Good Indication LTC1735 High Efficiency Synchronous Step-Down Controller LTC1736 LT1769 High Efficiency Synchronous Step-Down Controller with 5-Bit VID 2A Monolithic Battery Charger COMMENTS Adaptive PowerTM Mode, 24-Pin SSOP POR, Auxiliary Regulator POR, External Feedback Divider Auxiliary Regulator, 5V Standby 5V Standby, POR, Low Battery, Aux Regulator Constant Frequency, Standby, 5V and 3.3V LDOs Expandable Up to 12 Phases, G-28, Up to 120A 500kHz, 25MHz GBW, Error Amplifer 1.3V VOUT 3.5V, Current Mode Ensures Accurate Current Sharing, 3.5V VIN 36V Burst Mode Operation and Cycle Skip Low Current Modes, 3.5V VIN 36V VID Tables VRM 8.4 and VRM9.0, IOUT 40A Burst Mode Operation, 16-Pin Narrow SSOP, Fault Protection, 3.5V VIN 36V Output Fault Protection, Power Good, GN-24, 3.5V VIN 36V, 0.925V VOUT 2V CC/CV Switching DC/DC Converter, 5% Charge Accuracy, Adapter Current Limit for Maximum Charge Current No Sense Resistor Required, 4V VIN 36V, 0.8V VIN VIN, GN16 Adjustable Output Up to 40A, G-28 Extends Run Time by 10%, Reduces Charging Time by 50%, 36-Lead SSOP 0.6V VOUT 1.75V, IOUT 40A Precision Regulation, Up to 20A, Small PCB Area LTC1778 No RSENSETM Synchronous Current Mode Step-Down Controller LTC1929/LTC1929-PG 2-Phase High Efficiency Controller LTC1960 Dual Battery Charger/Selector with SPI Interface LTC3716 2-Phase High Efficiency Controller with 5-Bit VID and Power Good Indication LTC3717/LTC3831 DDR Memory Termination Regulators (VTT Supply) Adaptive Power and No RSENSE are a trademarks of Linear Technology Corporation. 3719i 32 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 q LT/TP 1201 1.5K * PRINTED IN USA FAX: (408) 434-0507 q www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2001 |
Price & Availability of LTC3719 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |