View L9826_241095.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

L9826
Octal Low-Side Driver for resistive and inductive loads with serial/parallel input control, output protection and diagnostic
s
OUTPUTS CURRENT CAPABILITY UP TO 500mA, RON = 2.2 AT TJ = 25C PARALLEL CONTROL INPUTS FOR OUTPUTS 1 AND 2 SPI CONTROL FOR OUTPUTS 1 TO 8 RESET FUNCTION WITH RESET SIGNAL AT NRES PIN OR UNDERVOLTAGE AT VCC - INTRINSIC OUTPUT VOLTAGE CLAMPING AT TYP. 50V OVERCURRENT SHUTDOWN AT OUTPUTS 3 TO 8 SHORT CIRCUIT CURRENT LIMITATION AND SELECTIVE THERMAL SHUTDOWN AT OUTPUTS 1 AND 2 OUTPUT STATUS DATA AVAILABLE ON THE SPI
SO20 (16+2+2) ORDERING NUMBER: L9826
s s s
s s s
DESCRIPTION The L9826 is a Octal Low-Side Driver Circuit, dedicated for automotive applications. Output voltage clamping is provided for flyback current recirculation, when inductive loads are driven. Chip Select and Serial Peripheral Interface for outputs control and diagnostic data transfer. Parallel Control inputs for two outputs.
s
BLOCK DIAGRAM
VCC
V CC
OUT1
1 2 3
NON1
Q1
S
Latch / Driver
R Overtemperature Detection
+ -
IOL
Diag1
Fault Latch
VDG
CH1 NON2
VCC
Q2 Diag2
CH2
OUT2 OUT3
SPI Interface
Output Latch
NCS
V CC
CLK
V CC
Shift Register
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
Q3
S
Latch / Driver
IOL
R
+
SDI
SDO
VCC
V CC
Diag1 Diag3 Diag2 Diag3 Diag4 Q4 Diag5 Diag4 Diag6 Diag7 Q5 Diag8 Diag5 Q6 Diag6
-
VDG
CH3 CH4 OUT4
CH5 CH6 CH7 CH8
OUT5 OUT6 OUT7 OUT8
nRES
VCC
Reset
Undervoltage RESET
Reset
Q7 Diag7 Q8 Diag8
GND
October 2002
1/12
L9826
PIN FUNCTION
N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Out 6 Out 1 nRes NCS GND GND NON1 SDO Out 8 Out 3 Out 5 Out 2 SDI CLK GND GND NON2 VCC Out 7 Out 4 output 6 output 1 asynchronous nRes chip select (active low) device ground device ground control input 1 serial data output output 8 output 3 output 5 output 2 serial data input serial clock device ground device ground control input 2 supply voltage output 7 output 4 Description
PIN CONNECTIONS (Top view)
OUT6 OUT1 nRES NCS GND GND NON1 SDO OUT8 OUT3
1 2 3 4 5 6 7 8 9 10
PINCON_L9826
20 19 18 17 16 15 14 13 12 11
OUT4 OUT7 Vcc NON2 GND GND CLK SDI OUT2 OUT5
2/12
L9826
ABSOLUTE MAXIMUM RATINGS For voltages and currents applied externally to the device
Symbol VCC Parameter Supply voltage Test Condition Min. -0.3 Typ. Max. 7 Unit V
Inputs and data lines (NONx, NCS, CLK, SDI, nRes) VIN IIN Voltage (NONx, NCS, CLK, SDI, nRes) Protection diodes current 1) T 1ms -0.3 -20 7 20 V mA
Outputs (Out1 ... Out8) VOUTc IOUT EOUTcl Continuous output voltage Output current 2) Output clamp energy IOUT 250mA -1,0 -2 45 1,0 10 V A mJ
Notes: 1. All inputs are protected against ESD according to MIL 883C; tested with HBM at 2KV. It corresponds to a dissipated energy E 0,2mJ. 2. Transient pulses in accordance to DIN40839 part 1, 3 and ISO 7637 Part 1, 3.
For currents determined within the device:
Symbol Parameter Test Condition Min. Typ. Max. Unit
Outputs (Out1 ... Out8) IOUT I O UT i i = 1-8 Output current (Out1 ... Out8) Total average-current all outputs
3)
1,0 2.0
A A
3. When operating the device with short circuit at more than 2 outputs at the same time, damage due to electrical overstress may occur.
THERMAL DATA
Symbol Thermal shutdown TJSC Thermal shutdown threshold 150 165 C Parameter Test Condition Min. Typ. Max. Unit
Thermal resistance RthjA-one RthjA-all Rthj-pin Single output (junction ambient) All outputs (junction ambient) Junction to Pin 90 75 18 C/W C/W C/W
3/12
L9826
ELECTRICAL CHARACTERISTCS (4.5V VCC 5,5V; -40C TJ 150C; unless otherwise specified)
Symbol Supply voltage IccSTB IccOPM Standby current Operating mode without load (nRes = Low) IOUT1 ... 8 = 500mA SPI - CLK = 3MHz NCS = LOW SDO no load Iout = -2A 70 5 A mA Parameter Test Condition Min. Typ. Max. Unit
ICC
ICC during reverse output current
100
mA
Inputs (NONx. NCS, CLK, SDI, nRes) VINL VINH Vhyst IIN RIN Low level High level Hysteresis voltage Input current Pullup resistance (NONx, NCS, CLK, SDI) Pulldown resistance (nRes) Input capacitance VIN = VCC -0.3 0.7*VCC 0.85 -10 50 10 250 0.2*VCC VCC+0,3 V V V A k
CIN
10
pF
Serial data outputs VSDOH VSDOL ISDOL CSDO High output level Low output level Tristate leakage current Output capacitance ISDO = -4mA ISDO = 3,2mA NCS = high; 0V VSDO VCC fSDO = 300kHz -10 VCC -0.4 0.4 10 10 V V A pF
Outputs OUT 1 ... 8 IOUTL1 - 8 Leakage current OUTx = OFF; VOUTx = 25V; VCC = 5V OUTx = OFF; VOUTx = 16V; VCC = 5V OUTx = OFF; VOUTx = 16V; VCC = 1V 1mA Iclp Ioutp; Itest = 10mA with correlation IOUT = 500mA; T j = +150C VOUT = 16V; f = 1MHz 45 100 A
IOUTL1 - 8 Leakage current
100
A
IOUTL1 - 8 Leakage current
10
A
Vclp
Output clamp voltage
62
V pF
RDSon COUT
On resistance OUT 1 ... 8 Output capacitance
3.0 300
4/12
L9826
ELECTRICAL CHARACTERISTCS (continued)
Symbol Parameter Test Condition Min. Typ. Max. Unit
Outputs short circuit protection ISBC ILIM tSCB Overcurrent shutoff threshold Short circuit current limitation Delay shutdown OUT3 ... OUT8 OUT1; OUT2 for output 3 ... 8; IOUT 1/2 ISCB 0.45 0.5 0.2 3,0 1.1 1,0 12 A A s
Diagnostics VDG IOL tdf Diagnostic threshold voltage Open load detection sink current Diagnostic detection filter time for output 1 & 2 on each diagnostic condition Vout = VDG 0.32*V
CC
0.4*VC
C
V A
20
100
15
50
s
Outputs timing tdon1 Turn ON delay of OUT 1 and 2 NON1, 2 = 50% to VOUT = 0,9*Vbat NCS = 50% to VOUT = 0,9*Vbat NCS = 50% to VOUT = 0,9*Vbat NCS = 50% to VOUT = 0,1*Vbat NON1, 2 = 50% to VOUT = 0,1*Vbat For output 3 to 8; 90% to 30% of Vbat; RL = 500; Vbat = 16V For output 1 and 2; 90% to 30% of Vbat; RL = 500; Vbat = 16V For output 1 to 8; 30% to 90% of Vbat; RL = 500; Vbat = 16V For output 1 to 8; 30% to 80% of Vbat; RL = 500; Vbat = 0.9 * Vclp 0.7 5 s
tdon2 tdoff
Turn ON delay of OUT 3 to 8 Turn OFF delay of OUT 1 to 8
10 10
s s
dUon1/dt dUon2/dt
Turn ON voltage slew-rate
3.5
V/s
Turn ON voltage slew-rate
2
10
V/s
dUoff1/dt
Turn OFF voltage slew-rate
2
10
V/s
dUoff2/dt
Turn OFF voltage slew-rate
2
15
V/s
Serial diagnostic link (Load capacitor at SDO = 100pF) fclk tclh tcll tpcld tcsdv tsclch Clock frequency Minimum time CLK = HIGH Minimum time CLK = LOW Propagation delay CLK to data at SDO valid NCS = LOW to data at SDO active CLK low before NCS low Setup time CLK to NCS change H/L 100 4,9V VCC 5,1V 50% duty cycle 3 160 160 100 MHz ns ns ns
100
ns
ns
5/12
L9826
ELECTRICAL CHARACTERISTCS (continued)
Symbol thclcl tscld thcld tsclcl thclch tpchdz Parameter CLK change L/H after NCS = low SDI input setup time CLK change H/L after SDI data valid SDI data hold after CLK change H/L 150 150 100 Multiple of 8 CLK cycles inside NCS period Test Condition Min. 100 Typ. Max. Unit ns
20
ns
SDI input hold time CLK low before NCS high CLK high after NCS high NCS L/H to output data float NCS pulse filter time
20
ns ns ns ns
FUNCTIONAL DESCRIPTION General The L9826 integrated circuit features 8 power low-side-driver outputs. Data is transmitted to the device using the Serial Peripheral Interface, SPI protocol. Outputs 1 and 2 can be controlled parallel or serial. The power outputs features voltage clamping function for flyback current recirculation and are protected against short circuit to Vbat. The diagnostics recognizes two outputs fault conditions: 1) overcurrent for outputs 3 to 8 , overcurrent and thermal overload for outputs 1 and 2 in switch-on condition and 2) open load or short to GND in switch-off condition for all outputs. The outputs status can be read out via the serial interface. The chip internal reset is a OR function of the external nRes signal and internally generated undervoltage nRes signal. Output Stages Control Each output is controlled with its latch and with common reset line, which enables all eight outputs. Outputs 1 and 2 can be controlled also by its NON1, NON2 inputs. It allows PWM control independently on the SPI. These inputs features internal pull-up resistors to assure that the outputs are switched off, when the inputs are open. The control data are transmitted via the SDI input, the timing of the serial interface is shown in Fig. 1. The device is selected with low NCS signal and the input data are transferred into the 8 bit shift register at every falling CLK edge. The rising edge of the NCS latches the new data from the shift register to the drivers.
6/12
L9826
Figure 1. Timing of the Serial Interface.
NCS
tsclch thclcl tclh tcll tsclcl thclch
CLK
tcsdv tpcld not defined tscld D8 thcld tpchdz D1
SDO
SDI
D8
D7
D1
The SPI register data are transferred to the output latch at rising NCS edge. The digital filter between NCS and the output latch ensures that the data are transferred only after 8 CLK cycles or multiple of 8 CLK cycles since the last NCS falling edge. The NCS changes only at low CLK. Outputs Control Tables :
Outputs 1, 2: NON1, 2 SPI-bit 1, 2 Output 1, 2 1 0 off 0 0 on 0 1 on 1 1 on SPI-bit 3 ... 8 Output 3 ... 8 0 off 1 on Outputs 3 to 8:
Figure 2. Output Control register structure
MSB Q2 Q4 Q6 Q8 Q1 Q3 Q5 LSB Q7
Control-bit output 7 Control-bit output 5 Control-bit output 3 Control-bit output 1 Control-bit output 8 Control-bit output 6 Control-bit output 4 Control-bit output 2
7/12
L9826
Power outputs characteristics for flyback current, outputs short circuit protection and diagnostics For output currents flowing into the circuit the output voltages are limited. The typical value of this voltage is 50V. This function allows that the flyback current of a inductive load recirculates into the circuit; the flyback energy is absorbed in the chip. Output short circuit protection for outputs 3 to 8 (dedicated for loads without inrush current): when the output current exceeds the short circuit threshold, the corresponding output overload latch is set and the output is switched off immediately. Output short circuit protection for outputs 1 and 2 (dedicated for loads with inrush current, as lamps): when the load current would exceed the short circuit limit value, the corresponding output goes in a current regulation mode. The output current is determined by the output characteristics and the output voltage depends on the load resistance. In this mode high power is dissipated in the output transistor and its temperature increases rapidly. When the power transistor temperature exceeds the thermal shutdown threshold, the overload latch is set and the corresponding output switched off. For the load diagnostic in output off condition each output features a diagnostic current sink, typ 60A. Diagnostics The output voltage at all outputs is compared with the diagnostic threshold, typ 0,38 * VCC. Outputs 1 and 2 features dedicated fault latches. The output status signal is filtered and latched. The fault latches are cleared during NCS low. The latch stores the status bit, so the first reading after the error occurred might be wrong. The second reading is right. Diagnostic Table for outputs 1 and 2 in parallel controlled mode:
Output 1, 2 off off on on Output-voltage > DG-threshold < DG-threshold < DG-threshold > DG-threshold Status-bit high low high low Output-mode correct operation fault condition 2) correct operation fault condition 1)
Fault condition 1) "output short circuit to Vbat" : the output was switched on and the voltage at the output exceeds the diagnostics threshold. The output operates in current regulation mode or has been switched off due to thermal shutdown. The status bit is low. Fault condition 2) "open load" or "output short circuit to GND" : the output is switched off and the voltage at the output drops below the diagnostics threshold, because the load current is lower than the output diagnostic current source, the load is interrupted. The diagnostic bit is low. For outputs 3 to 8 the output status signals, are fed directly to the SPI register. Diagnostic Table for outputs 1 to 8 in SPI controlled mode:
Output 1 ... 8 off off on on Output-voltage > DG-threshold < DG-threshold < DG-threshold > DG-threshold Status-bit high low low high Output-mode correct operation fault condition 2) correct operation fault condition 1)
8/12
L9826
The fault condition 1) "output short circuit to Vbat" : the output was switched on and the voltage at the output exceeded the diagnostics threshold due to overcurrent, the output overload latch was set and the output has been switched off. The diagnostic bit is high. Fault condition 2) "open load" or "output short circuit to GND" is the same as of outputs 1 and 2. At the falling edge of NCS the output status data are transferred to the shift register. When NSC is low, data bits contained in the shift register are transferred to SDO output et every rising CLK edge. Figure 3. The Pulse Diagram to Read the Outputs Status Register
NCS CLK SDO SDI MSB 6 6 5 5 4 4 3 3 2 2 1 1 LSB LSB
MSB
Figure 4. The Structure of the Outputs Status Register
MSB LSB
Diag2 Diag4 Diag6 Diag8 Diag1 Diag3 Diag5 Diag7
Diagnostic-bit output 7 Diagnostic-bit output 5 Diagnostic-bit output 3 Diagnostic-bit output 1 Diagnostic-bit output 8 Diagnostic-bit output 6 Diagnostic-bit output 4 Diagnostic-bit output 2
9/12
L9826
APPLICATION INFORMATION The typical application diagram is shown in Fig. 5. Figure 5. Typical Application Circuit Diagram for the L9826 Circuit.
VCC
VOLTAGE REGULATOR
VBAT
VCC OUT1
1 2 3
VC C
NON1
Q1
S
Latch / Driver
R Overtemperature Detection
+ -
IO L
Diag1
Fault Latch
VD G
CH1 NON2
V CC
Q2 Diag2
CH2
OUT2 OUT3
SPI Interface
Output Latch
NCS
VC C
CLK
VC C
Shift Register
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
Q3
S
Latch / Driver
IO L
R
+ -
SDI
SDO
VC C
VC C
Diag1 Diag3 Diag2 Diag3 Diag4 Q4 Diag5 Diag4 Diag6 Diag7 Q5 Diag8 Diag5 Q6 Diag6
VD G
CH3 CH4 OUT4
CH5
OUT5
CH6 CH7
OUT6
P
NCS2 ... 7 CLOCK NRES SDO SDI
nRES
VC C
Reset
Undervoltage RE SET
Reset
Q7 Diag7 Q8 Diag8
OUT7 OUT8
CH8
L9826
GND
R, L loads
L9826
For higher current driving capability two outputs of the same kind can be paralleled. In this case the maximum flyback energy should not exceed the limit value for single output. The immunity of the circuit with respect to the transients at the output is verified during the characterization for Test Pulses 1, 2 and 3a, 3b, DIN40839 or ISO7637 part 3. The Test Pulses are coupled to the outputs with 200pF series capacitor. All outputs withstand testpulses without damage. The correct function of the circuit with the Test Pulses coupled to the outputs is verified during the characterization for the typical application with R = 30 to 100, L= 0 to 600mH loads. The Test Pulses are coupled to the outputs with 200pF series capacitor.
10/12
L9826
mm DIM. MIN. A A1 B C D E e H h L K 10 0.25 0.4 2.35 0.1 0.33 0.23 12.6 7.4 1.27 10.65 0.75 1.27 0.394 0.010 0.016 TYP. MAX. 2.65 0.3 0.51 0.32 13 7.6 MIN. 0.093 0.004 0.013 0.009 0.496 0.291
inch TYP. MAX. 0.104 0.012 0.020 0.013 0.512 0.299 0.050 0.419 0.030 0.050
OUTLINE AND MECHANICAL DATA
SO20
0 (min.)8 (max.)
L
h x 45
A B e K H D A1 C
20
11 E
1
0 1
SO20MEC
11/12
L9826
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (R) 2002 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com
12/12

▲Up To Search▲

Price & Availability of L9826

	To Download L9826 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .