|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
STA505 40V 3.5A QUAD POWER HALF BRIDGE s MINIMUM INPUT OUTPUT PULSE WIDTH DISTORTION 200m RdsON COMPLEMENTARY DMOS OUTPUT STAGE CMOS COMPATIBLE LOGIC INPUTS THERMAL PROTECTION THERMAL WARNING OUTPUT UNDER VOLTAGE PROTECTION MULTIPOWER BCD TECHNOLOGY s s s s s PowerSO36 ORDERING NUMBER: STA505 DESCRIPTION STA505 is a monolithic quad half bridge stage in Multipower BCD Technology. The device can be used as dual bridge or reconfigured, by connecting CONFIG pin to Vdd pin, as single bridge with double current capability, and as half bridge (Binary mode) with half current capability. The device is particularly designed to make the outAUDIO APPLICATION CIRCUIT (Dual BTL) VCC1A IN1A IN1A +3.3V IBIAS CONFIG PWRDN R57 10K R59 10K C58 100nF TH_WAR IN1B VDD VDD VSS VSS C58 100nF C53 100nF C60 100nF IN2A VCCSIGN VCCSIGN IN2A GND-Reg GND-Clean 21 22 33 34 M17 35 8 9 36 31 20 19 M16 M15 REGULATORS 7 VCC2A C32 1F OUT2A OUT2A 6 GND2A PWRDN FAULT 23 24 25 27 26 TRI-STATE PROTECTIONS & LOGIC M5 28 30 M4 13 M2 29 M3 15 17 16 C30 1F OUT1A OUT1A 14 GND1A C52 330pF +VCC C55 1000F put stage of a stereo All-Digital High Efficiency (DDXTM) amplifier capable to deliver 50 + 50W @ THD = 10% at Vcc 30V output power on 8 load and 80W @ THD = 10% at Vcc 36V on 8 load in single BTL configuration. The input pins have threshold proportional to Ibias pin voltage. L18 22H C20 100nF R98 6 C99 100nF C23 470nF C101 100nF 12 VCC1B C31 1F OUT1B OUT1B GND1B R63 20 R100 6 C21 100nF L19 22H 11 10 TH_WAR IN1B L113 22H C110 100nF C109 330pF R103 6 R104 20 4 VCC2B C33 1F OUT2B OUT2B R102 6 C111 100nF 3 2 C107 100nF C108 470nF C106 100nF IN2B IN2B GNDSUB 32 M14 L112 22H 1 5 GND2B D00AU1148B July 2003 1/9 STA505 PIN FUNCTION N 1 35 ; 36 15 12 7 4 14 13 6 5 16 ; 17 10 ; 11 8;9 2;3 29 30 31 32 21 ; 22 33 ; 34 25 26 27 24 28 19 23 18 20 Pin GND-SUB Vcc Sign Vcc1A Vcc1B Vcc2A Vcc2B GND1A GND1B GND2A GND2B OUT1A OUT1B OUT2A OUT2B IN1A IN1B IN2A IN2B Vdd Vss PWRDN TRI-STATE FAULT CONFIG TH-WAR GND-clean IBIAS NC GND-Reg Substrate ground Signal Positive Supply Positive Supply Positive Supply Positive Supply Positive Supply Negative Supply Negative Supply Negative Supply Negative Supply Output half bridge 1A Output half bridge 1B Output half bridge 2A Output half bridge 2B Input of half bridge 1A Input of half bridge 1B Input of half bridge 2A Input of half bridge 2B 5V Regulator referred to ground 5V Regulator referred to +Vcc Stand-by pin Hi-Z pin Fault pin advisor Configuration pin Thermal warning advisor Logical ground High logical state setting voltage Not connected Ground for regulator Vdd Description 2/9 STA505 FUNCTIONAL PIN STATUS PIN NAME FAULT FAULT (*) TRI-STATE TRI-STATE PWRDN PWRDN THWAR THWAR(*) CONFIG CONFIG(**) Logical value 0 1 0 1 0 1 0 1 0 1 IC -STATUS Fault detected (Short circuit, or Thermal ..) Normal Operation All powers in Hi-Z state Normal operation Low absorpion Normal operation Temperature of the IC =130C Normal operation Normal Operation OUT1A=OUT1B ; OUT2A=OUT2B (IF IN1A = IN1B; IN2A = IN2B) (*) : The pin is open collector. To have the high logic value, it needs to be pulled up by a resistor. (**): To put CONFIG = 1 means connect Pin 24 (CONFIG) to Pins 21, 22 (Vdd) PIN CONNECTION VCCSign VCCSign VSS VSS IN2B IN2A IN1B IN1A TH_WAR FAULT TRI-STATE PWRDN CONFIG IBIAS VDD VDD GND-Reg GND-Clean 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 D01AU1273 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 GND-SUB OUT2B OUT2B VCC2B GND2B GND2A VCC2A OUT2A OUT2A OUT1B OUT1B VCC1B GND1B GND1A VCC1A OUT1A OUT1A N.C. 3/9 STA505 ABSOLUTE MAXIMUM RATINGS Symbol VCE Vmax Top Tstg, Tj Parameter DC Supply Voltage (Pin 4,7,12,15) Maximum Voltage on pins 23 to 32 Operating Temperature Range Storage and Junction Temperature Value 40 5.5 0 to 70 -40 to 150 Unit V V C C THERMAL DATA Symbol Tj-case TjSD Twarn thSD Parameter Thermal Resistance Junction to Case (thermal pad) Thermal shut-down junction temperature Thermal warning temperature Thermal shut-down hysteresis 150 130 25 Min. Typ. Max. 2.5 Unit C/W C C C ELECTRICAL CHARACTERISTCS (Ibias = 3.3V; Vcc = 30V; T = 25C unless otherwise specified) Symbol RdsON Idss gN gP Dt_s Dt_d td ON td OFF tr tf VCC VIN-H VIN-L IIN-H IIN-L Parameter Power Pchannel/Nchannel MOSFET RdsON Power Pchannel/Nchannel leakage Idss Power Pchannel RdsON Matching Power Nchannel RdsON Matching Low current Dead Time (static) Id=1A; Vcc=35V Id=1A Id=1A see test circuit no.1; see fig. 1 95 95 10 20 50 100 100 25 25 9 36 Ibias/2 +300mV Ibias/2 -300mV Pin voltage = Ibias Pin voltage = 0.3V 1 1 Test conditions Min. Typ. 200 Max. 270 50 Unit m A % % ns ns ns ns ns ns V V V A A High current Dead Time (dinamic) L=22H; C = 470nF; Rl = 8 Id=3.5A; see fig. 3 Turn-on delay time Turn-off delay time Rise time Fall time Supply voltage operating voltage High level input voltage Low level input voltage Hi level Input current Low level input current Resistive load Resistive load Resistive load; as fig.1; Resistive load; as fig. 1; 4/9 STA505 ELECTRICAL CHARACTERISTCS (continued) Symbol Parameter Test conditions Ibias = 3.3V Ibias = 3.3V Ibias = 3.3V PWRDN = 0 0.8 1.7 3 Min. Typ. 35 Max. Unit A V V mA IPWRDN-H Hi level PWRDN pin input current VL VH IVCCPWRDN IFAULT Low logical state voltage VL (pin PWRDN, TRISTATE) (note 1) High logical state voltage VH (pin PWRDN, TRISTATE) (note 1) Supply current from Vcc in Power Down Output Current pins FAULT -TH-WARN when FAULT CONDITIONS Supply current from Vcc in Tristate Supply current from Vcc in operation both channel switching) Isc (short circuit current limit) (note 2) Undervoltage protection threshold Output minimum pulse width Vpin = 3.3V Tri-state=0 Input pulse width = 50% Duty; Switching Frequency = 384Khz; No LC filters; 3.5 1 22 80 mA mA mA IVCC-hiz IVCC IVCC-q IOUT-SH VOV 6 7 8 A V No Load 70 150 ns Notes: 1. The following table explains the VL, VH variation with Ibias Ibias 2.7 3.3 5 VLmin 0.7 0.8 0.85 VHmax 1.5 1.7 1.85 Unit V V V Note 2: If used in single BTL configuration, the device may be not short circuit protected LOGIC TRUTH TABLE (see fig. 2) TRI-STATE 0 1 1 1 1 INxA x 0 0 1 1 INxB x 0 1 0 1 Q1 OFF OFF OFF ON ON Q2 OFF OFF ON OFF ON Q3 OFF ON ON OFF OFF Q4 OFF ON OFF ON OFF OUTPUT MODE Hi-Z DUMP NEGATIVE POSITIVE Not used 5/9 STA505 Figure 1. Test Circuit. OUTxY Vcc (3/4)Vcc Low current dead time = MAX(DTr,DTf) (1/2)Vcc (1/4)Vcc +Vcc t Duty cycle = 50% M58 DTr OUTxY M57 DTf INxY R 8 + - V67 = vdc = Vcc/2 D03AU1458 gnd Figure 2. +VCC Q1 INxA OUTxA Q2 OUTxB INxB Q3 Q4 GND D00AU1134 Figure 3. High Current Dead time for Bridge application = ABS(DTout(A)-DTin(A))+ABS(DTOUT(B)-DTin(B)) +VCC Duty cycle=A Duty cycle=B DTout(A) M58 Q1 OUTxA Rload=8 L67 22 C69 470nF DTout(B) L68 22 C70 470nF Q2 OUTxB M64 DTin(A) INxA DTin(B) INxB Iout=3.5A M57 Q3 Iout=3.5A Q4 M63 C71 470nF Duty cycle A and B: Fixed to have DC output current of 3.5A in the direction shown in figure D00AU1162 6/9 STA505 Figure 4. Typical Single BTL Configuration to obtain 80W @ THD 10%, R L = 8, VCC = 36V (note 1) IBIAS 100nF +3.3V 23 18 17 16 11 10 N.C. 22H OUT1A OUT1A OUT1B OUT1B OUT2A 22 1/2W 6.2 1/2W 6.2 1/2W GND-Clean GND-Reg 19 20 100nF FILM 100nF X7R 470nF FILM 100nF X7R 100nF FILM 22H 10K 100nF X7R VDD VDD CONFIG 21 22 24 28 25 27 26 8 9 8 OUT2A OUT2B 330pF TH_WAR nPWRDN 10K TH_WAR PWRDN FAULT TRI-STATE 100nF IN1A IN1B IN2A IN2B VSS VSS 100nF X7R 100nF X7R Add. VCCSIGN VCCSIGN GNDSUB 3 2 OUT2B 15 VCC1A 1F X7R +36V 2200F 63V 29 30 31 32 33 34 12 VCC1B VCC2A IN1A 7 +36V 1F X7R IN1B 4 14 VCC2B GND1A GND1B 35 13 GND2A 36 1 6 GND2B 5 D01AU1274 Note: 1. "A PWM modulator as driver is needed . In particular, this result is performed using the STA30X+STA50X demo board". Figure 5. Typical Quad Half bridge Configuration VCC1P IN1A IN1A +3.3V IBIAS CONFIG PWRDN R57 10K R59 10K C58 100nF TH_WAR IN1B VDD VDD VSS VSS C58 100nF C53 100nF C60 100nF IN2A VCCSIGN VCCSIGN IN2A GND-Reg GND-Clean 21 22 33 34 M17 35 8 9 36 31 20 19 M16 M15 OUTPR OUTPR 6 PGND2P R43 20 C43 330pF L13 22H C73 100nF R53 6 C83 100nF R66 5K REGULATORS 7 VCC2P PWRDN FAULT 23 24 25 27 26 TRI-STATE PROTECTIONS & LOGIC M5 28 30 M4 13 M2 29 M3 15 17 16 OUTPL OUTPL 14 PGND1P R41 20 C41 330pF L11 22H C71 100nF R51 6 C81 100nF R62 5K R61 5K +VCC C21 2200F C31 820F C91 1F 12 VCC1N C51 1F OUTNL OUTNL PGND1N C61 100nF L12 22H R42 20 C42 330pF C72 100nF R52 6 C82 100nF R64 5K 11 10 TH_WAR IN1B R63 5K C32 820F C92 1F R65 5K C33 820F C93 1F 4 VCC2N C52 1F OUTNR OUTNR C62 100nF L14 22H R44 20 C44 330pF C74 100nF R54 6 C84 100nF R68 5K 3 2 IN2B R67 5K C34 820F IN2B GNDSUB 32 M14 1 5 PGND2N C94 1F D03AU1474 For more information refer to the application notes AN1456 and AN1661 7/9 STA505 DIM. A A2 A4 A5 a1 b c D D1 D2 E E1 E2 E3 E4 e e3 G H h L N s MIN. 3.25 0.8 mm TYP. MAX. 3.5 3.3 1 0.075 0.38 0.32 16 9.8 MIN. 0.128 0.031 inch TYP. MAX. 0.138 0.13 0.039 0.003 0.015 0.012 0.630 0.38 OUTLINE AND MECHANICAL DATA 0.2 0 0.22 0.23 15.8 9.4 1 13.9 10.9 5.8 2.9 0.65 11.05 0 15.5 0.8 0.075 0 15.9 0.61 1.1 1.1 0.031 10 (max) 8 (max) 14.5 11.1 2.9 6.2 3.2 0.547 0.429 0.228 0.114 0 0.008 0.009 0.622 0.37 0.008 0.039 0.57 0.437 0.114 0.244 1.259 0.026 0.435 0.003 0.625 0.043 0.043 PowerSO36 (SLUG UP) (1) "D and E1" do not include mold flash or protusions. Mold flash or protusions shall not exceed 0.15mm (0.006") (2) No intrusion allowed inwards the leads. 7183931 8/9 STA505 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com (R) DDX is a trademark of Apogee tecnology inc. 9/9 |
Price & Availability of STA505 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |