View M1MA151WAT1_138694.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document by M1MA151WAT1/D
Common Anode Silicon Dual Switching Diodes
These Common Anode Silicon Epitaxial Planar Dual Diodes are designed for use in ultra high speed switching applications. These devices are housed in the SC-59 package which is designed for low power surface mount applications. * Fast trr, < 10 ns * Low CD, < 15 pF * Available in 8 mm Tape and Reel Use M1MA151/2WAT1 to order the 7 inch/3000 unit reel. Use M1MA151/2WAT3 to order the 13 inch/10,000 unit reel.
ANODE 3
M1MA151WAT1 M1MA152WAT1
Motorola Preferred Devices
SC-59 PACKAGE COMMON ANODE DUAL SWITCHING DIODES 40/80 V-100 mA SURFACE MOUNT
3
2
1 CATHODE
2 1
MAXIMUM RATINGS (TA = 25C)
Rating Reverse Voltage M1MA151WAT1 M1MA152WAT1 Peak Reverse Voltage M1MA151WAT1 M1MA152WAT1 Forward Current Single Dual Peak Forward Current Single Dual Peak Forward Surge Current Single Dual IFSM(1) IFM IF VRM Symbol VR Value 40 80 40 80 100 150 225 340 500 750
Unit Vdc
CASE 318D-03, STYLE 5 SC-59
Vdc
mAdc
mAdc
mAdc
THERMAL CHARACTERISTICS
Rating Power Dissipation Junction Temperature Storage Temperature Symbol PD TJ Tstg Max 200 150 - 55 to + 150 Unit mW C C
ELECTRICAL CHARACTERISTICS (TA = 25C)
Characteristic Reverse Voltage Leakage Current M1MA151WAT1 M1MA152WAT1 Forward Voltage Reverse Breakdown Voltage M1MA151WAT1 M1MA152WAT1 Diode Capacitance Reverse Recovery Time 1. t = 1 SEC 2. trr Test Circuit Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
Symbol IR VF VR CD trr(2)
Condition VR = 35 V VR = 75 V IF = 100 mA IR = 100 A VR = 0, f = 1.0 MHz IF = 10 mA, VR = 6.0 V, RL = 100 , Irr = 0.1 IR
Min -- -- -- 40 80 -- --
Max 0.1 0.1 1.2 -- -- 15 10
Unit Adc
Vdc Vdc
pF ns
REV 3
Motorola Small-Signal Transistors, FETs and Diodes Device Data (c) Motorola, Inc. 1996
1
M1MA151WAT1 M1MA152WAT1
RECOVERY TIME EQUIVALENT TEST CIRCUIT INPUT PULSE
tr tp IF t RL 10% Irr = 0.1 IR 90% VR tp = 2 s tr = 0.35 ns IF = 10 mA VR = 6 V RL = 100
OUTPUT PULSE
trr t
A
DEVICE MARKING -- EXAMPLE
Marking Symbol
Type No. Symbol 151WA MN 152WA MO
MNX
The "X" represents a smaller alpha digit Date Code. The Date Code indicates the actual month in which the part was manufactured.
2
Motorola Small-Signal Transistors, FETs and Diodes Device Data
M1MA151WAT1 M1MA152WAT1
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection
0.037 0.95
interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process.
0.037 0.95
0.098-0.118 2.5-3.0 0.094 2.4 0.039 1.0 0.031 0.8
inches mm
SC-59 POWER DISSIPATION
The power dissipation of the SC-59 is a function of the pad size. This can vary from the minimum pad size for soldering to the pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient; and the operating temperature, TA . Using the values provided on the data sheet, PD can be calculated as follows: PD = TJ(max) - TA RJA the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 200 milliwatts. PD = 150C - 25C = 200 milliwatts 625C/W
The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into
The 625C/W assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 200 milliwatts. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal CladTM. Using a board material such as Thermal Clad, a power dissipation of 400 milliwatts can be achieved using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference should be a maximum of 10C.
* The soldering temperature and time should not exceed * When shifting from preheating to soldering, the * After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. * Mechanical stress or shock should not be applied during cooling * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. maximum temperature gradient should be 5C or less. 260C for more than 10 seconds.
Motorola Small-Signal Transistors, FETs and Diodes Device Data
3
M1MA151WAT1 M1MA152WAT1
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. A solder stencil is required to screen the optimum amount of solder paste onto the footprint. The stencil is made of brass or stainless steel with a typical thickness of 0.008 inches. The stencil opening size for the SC-59 package should be the same as the pad size on the printed circuit board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones, and a figure for belt speed. Taken together, these control settings make up a heating "profile" for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 1 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. The line on the graph shows the actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177 -189C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints.
STEP 1 PREHEAT ZONE 1 "RAMP" 200C
STEP 2 STEP 3 VENT HEATING "SOAK" ZONES 2 & 5 "RAMP"
DESIRED CURVE FOR HIGH MASS ASSEMBLIES 150C
STEP 6 STEP 7 STEP 5 STEP 4 VENT COOLING HEATING HEATING ZONES 3 & 6 ZONES 4 & 7 205 TO 219C "SPIKE" "SOAK" PEAK AT 170C SOLDER JOINT 160C
150C 100C 100C DESIRED CURVE FOR LOW MASS ASSEMBLIES 50C 140C
SOLDER IS LIQUID FOR 40 TO 80 SECONDS (DEPENDING ON MASS OF ASSEMBLY)
TIME (3 TO 7 MINUTES TOTAL)
TMAX
Figure 1. Typical Solder Heating Profile
4
Motorola Small-Signal Transistors, FETs and Diodes Device Data
M1MA151WAT1 M1MA152WAT1
PACKAGE DIMENSIONS
A L
3 2 1
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. DIM A B C D G H J K L S MILLIMETERS MIN MAX 2.70 3.10 1.30 1.70 1.00 1.30 0.35 0.50 1.70 2.10 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.65 2.50 3.00 INCHES MIN MAX 0.1063 0.1220 0.0512 0.0669 0.0394 0.0511 0.0138 0.0196 0.0670 0.0826 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0649 0.0985 0.1181
S
B
D G
C H K
J
STYLE 5: PIN 1. CATHODE 2. CATHODE 3. ANODE
CASE 318D-03 ISSUE E SC-59
Motorola Small-Signal Transistors, FETs and Diodes Device Data
5
M1MA151WAT1 M1MA152WAT1
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
6
M1MA151WAT1/D Motorola Small-Signal Transistors, FETs and Diodes Device Data
*M1MA151WAT1/D*

▲Up To Search▲

Price & Availability of M1MA151WAT1

	To Download M1MA151WAT1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .