|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
12-Bit CCD Signal Processor with Precision Timing TM Generator AD9995 FEATURES 6-Phase Vertical Transfer Clock Support Correlated Double Sampler (CDS) 6 dB to 42 dB 10-Bit Variable Gain Amplifier (VGA) 12-Bit 36 MHz A/D Converter Black Level Clamp with Variable Level Control Complete On-Chip Timing Generator Precision Timing Core with <600 ps Resolution On-Chip 3 V Horizontal and RG Drivers 2-Phase and 4-Phase H-Clock Modes Electronic and Mechanical Shutter Modes On-Chip Driver for External Crystal On-Chip Sync Generator with External Sync Input 56-Lead LFCSP Package APPLICATIONS Digital Still Cameras Digital Video Camcorders Industrial Imaging GENERAL DESCRIPTION The AD9995 is a highly integrated CCD signal processor for digital still camera and camcorder applications. It includes a complete analog front end with A/D conversion, combined with a full-function programmable timing generator. The timing generator is capable of supporting both 4- and 6-phase vertical clocking. A Precision Timing core allows adjustment of high speed clocks with less than 600 ps resolution at 36 MHz operation. The AD9995 is specified at pixel rates of up to 36 MHz. The analog front end includes black level clamping, CDS, VGA, and a 12-bit A/D converter. The timing generator provides all the necessary CCD clocks: RG, H-clocks, V-clocks, sensor gate pulses, substrate clock, and substrate bias control. Operation is programmed using a 3-wire serial interface. Packaged in a space-saving 56-lead LFCSP, the AD9995 is specified over an operating temperature range of -20C to +85C. FUNCTIONAL BLOCK DIAGRAM VRT VRB AD9995 6dB TO 42dB CCDIN CDS VGA VREF 12-BIT ADC 12 DOUT CLAMP INTERNAL CLOCKS DCLK RG 4 HORIZONTAL DRIVERS H1-H4 PRECISION TIMING GENERATOR MSHUT STROBE V1-V6 6 V-H CONTROL SYNC GENERATOR INTERNAL REGISTERS VSG1-VSG5 5 VSUB SUBCK HD VD SYNC CLI CLO SL SCK DATA REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P Box 9106, Norwood, MA 02062-9106, U.S.A. .O. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2003 Analog Devices, Inc. All rights reserved. AD9995 TABLE OF CONTENTS SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Digital Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 AD9995 Analog Specifications . . . . . . . . . . . . . . . . . . . . . . 4 Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . 5 PACKAGE THERMAL CHARACTERISTICS. . . . . . . . . . . 5 ORDERING GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . 6 TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 EQUIVALENT CIRCUITS. . . . . . . . . . . . . . . . . . . . . . . . . . 7 TYPICAL PERFORMANCE CHARACTERISTICS . . . . . . 8 SYSTEM OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PRECISION TIMING HIGH SPEED TIMING GENERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Timing Resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 High Speed Clock Programmability . . . . . . . . . . . . . . . . . 10 H-Driver and RG Outputs . . . . . . . . . . . . . . . . . . . . . . . . 11 Digital Data Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 HORIZONTAL CLAMPING AND BLANKING . . . . . . . . 13 Individual CLPOB and PBLK Patterns. . . . . . . . . . . . . . . 13 Individual HBLK Patterns . . . . . . . . . . . . . . . . . . . . . . . . 13 Generating Special HBLK Patterns. . . . . . . . . . . . . . . . . . 14 Generating HBLK Line Alternation . . . . . . . . . . . . . . . . . 14 HORIZONTAL TIMING SEQUENCE EXAMPLE . . . . . . 15 VERTICAL TIMING GENERATION . . . . . . . . . . . . . . . . 16 Vertical Pattern Groups (VPAT) . . . . . . . . . . . . . . . . . . . . 17 Vertical Sequences (VSEQ) . . . . . . . . . . . . . . . . . . . . . . . . 18 Complete Field: Combining V-Sequences . . . . . . . . . . . . . 19 Generating Line Alternation for V-Sequence and HBLK . . 20 Second V-Pattern Group during VSG Active Line . . . . . . . 20 Sweep Mode Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Multiplier Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Vertical Sensor Gate (Shift Gate) Patterns . . . . . . . . . . . . . 22 MODE Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 VERTICAL TIMING EXAMPLE . . . . . . . . . . . . . . . . . . . . Important Note about Signal Polarities . . . . . . . . . . . . . . . SHUTTER TIMING CONTROL . . . . . . . . . . . . . . . . . . . . Normal Shutter Operation . . . . . . . . . . . . . . . . . . . . . . . . High Precision Shutter Operation . . . . . . . . . . . . . . . . . . . Low Speed Shutter Operation . . . . . . . . . . . . . . . . . . . . . . SUBCK Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . Readout after Exposure. . . . . . . . . . . . . . . . . . . . . . . . . . . Using the TRIGGER Register . . . . . . . . . . . . . . . . . . . . . . VSUB Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSHUT and STROBE Control . . . . . . . . . . . . . . . . . . . . TRIGGER Register Limitations . . . . . . . . . . . . . . . . . . . . EXPOSURE AND READOUT EXAMPLE . . . . . . . . . . . . AFE DESCRIPTION AND OPERATION . . . . . . . . . . . . . DC Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Correlated Double Sampler . . . . . . . . . . . . . . . . . . . . . . . Variable Gain Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical Black Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Data Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . POWER-UP AND SYNCHRONIZATION . . . . . . . . . . . . . Recommended Power-Up Sequence for Master Mode. . . . Generating Software SYNC without External SYNC Signal . . . . . . . . . . . . . . . . . . . . . . . . . SYNC during Master Mode Operation . . . . . . . . . . . . . . . Power-Up and Synchronization in Slave Mode . . . . . . . . . STANDBY MODE OPERATION . . . . . . . . . . . . . . . . . . . . CIRCUIT LAYOUT INFORMATION . . . . . . . . . . . . . . . . SERIAL INTERFACE TIMING . . . . . . . . . . . . . . . . . . . . . Register Address Banks 1 and 2. . . . . . . . . . . . . . . . . . . . . Updating of New Register Values. . . . . . . . . . . . . . . . . . . . COMPLETE LISTING OF REGISTER BANK 1 . . . . . . . COMPLETE LISTING OF REGISTER BANK 2 . . . . . . . OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 24 24 26 26 26 26 27 27 27 28 28 29 30 31 31 31 31 32 32 32 33 33 33 34 34 34 36 37 38 39 40 43 59 -2- REV. 0 AD9995-SPECIFICATIONS Parameter TEMPERATURE RANGE Operating Storage POWER SUPPLY VOLTAGE AVDD (AFE Analog Supply) TCVDD (Timing Core Analog Supply) RGVDD (RG Driver) HVDD (H1-H4 Drivers) DRVDD (Data Output Drivers) DVDD (Digital) POWER DISSIPATION (See TPC 1 for Power Curves) 36 MHz, Typ Supply Levels, 100 pF H1-H4 Loading Power from HVDD Only* Standby 1 Mode Standby 2 Mode Standby 3 Mode MAXIMUM CLOCK RATE (CLI) *The total power dissipated by the HVDD supply may be approximated using the equation Total HVDD Power = C LOAD x HVDD x Pixel Frequency x HVDD x Number of H - outputs used H- Reducing the H-loading, using only two of the outputs, and/or using a lower HVDD supply will reduce the power dissipation. Specifications subject to change without notice. Min -20 -65 2.7 2.7 2.7 2.7 2.7 2.7 Typ Max +85 +150 Unit C C V V V V V V mW mW mW mW mW MHz 3.0 3.0 3.0 3.0 3.0 3.0 360 130 130 12 0.5 3.6 3.6 3.6 3.6 3.6 3.6 36 [ ] DIGITAL SPECIFICATIONS Parameter LOGIC INPUTS High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current Input Capacitance LOGIC OUTPUTS (Except H and RG) High Level Output Voltage @ IOH = 2 mA Low Level Output Voltage @ IOL = 2 mA RG and H-DRIVER OUTPUTS (H1-H4) High Level Output Voltage @ Max Current Low Level Output Voltage @ Max Current Maximum Output Current (Programmable) Maximum Load Capacitance (For Each Output) Specifications subject to change without notice. Symbol VIH VIL IIH IIL CIN VOH VOL VOH VOL Min 2.1 Typ Max Unit V V A A pF V V V V mA pF 10 10 10 2.2 0.6 0.5 VDD - 0.5 30 100 0.5 REV. 0 -3- AD9995 ANALOG SPECIFICATIONS (AVDD = 3.0 V, f Parameter CDS* Allowable CCD Reset Transient Max Input Range before Saturation Max CCD Black Pixel Amplitude VARIABLE GAIN AMPLIFIER (VGA) Gain Control Resolution Gain Monotonicity Gain Range Min Gain (VGA Code 0) Max Gain (VGA Code 1023) BLACK LEVEL CLAMP Clamp Level Resolution Clamp Level Min Clamp Level (Code 0) Max Clamp Level (Code 255) A/D CONVERTER Resolution Differential Nonlinearity (DNL) No Missing Codes Full-Scale Input Voltage VOLTAGE REFERENCE Reference Top Voltage (REFT) Reference Bottom Voltage (REFB) SYSTEM PERFORMANCE Gain Accuracy Low Gain (VGA Code 0) Max Gain (VGA Code 1023) Peak Nonlinearity, 500 mV Input Signal Total Output Noise Power Supply Rejection (PSR) *Input signal characteristics defined as follows: CLI = 36 MHz, Typical Timing Specifications, TMIN to TMAX, unless otherwise noted.) Typ 500 Min Max Unit mV V p-p mV Steps Notes 1.0 50 1024 Guaranteed 6 42 256 0 255 12 -1.0 dB dB Steps Measured at ADC output. LSB LSB Bits LSB V V V Includes entire signal chain. 0.5 Guaranteed 2.0 2.0 1.0 +1.0 5.0 40.5 5.5 41.5 0.2 0.8 50 6.0 42.5 dB dB % LSB rms dB Gain = (0.0351 Code) + 6 dB 12 dB gain applied. AC grounded input, 6 dB gain applied. Measured with step change on supply. 500mV TYP RESET TRANSIENT 50mV MAX OPTICAL BLACK PIXEL 1V MAX INPUT SIGNAL RANGE Specifications subject to change without notice. -4- REV. 0 AD9995 TIMING SPECIFICATIONS (C = 20 pF, AVDD = DVDD = DRVDD = 3.0 V, f L CLI = 36 MHz, unless otherwise noted.) Min 27.8 11.2 2 Typ Max Unit ns ns ns Pixels ns ns Cycles MHz ns ns ns ns ns Parameter MASTER CLOCK, CLI (Figure 4) CLI Clock Period CLI High/Low Pulsewidth Delay from CLI Rising Edge to Internal Pixel Position 0 AFE CLPOB Pulsewidth 1, 2 Symbol tCONV tCLIDLY 13.9 6 20 13.9 8 11 16.6 (Figures 9 and 14) 1 AFE SAMPLE LOCATION (Figure 7) SHP Sample Edge to SHD Sample Edge DATA OUTPUTS (Figures 8a and 8b) Output Delay from DCLK Rising Edge1 Pipeline Delay from SHP/SHD Sampling to DOUT SERIAL INTERFACE (Figures 40a and 40b) Maximum SCK Frequency SL to SCK Setup Time SCK to SL Hold Time SDATA Valid to SCK Rising Edge Setup SCK Falling Edge to SDATA Valid Hold SCK Falling Edge to SDATA Valid Read tS1 tOD 12.5 fSCLK tLS tLH tDS tDH tDV 10 10 10 10 10 10 NOTES 1Parameter is programmable. 2Minimum CLPOB pulsewidth is for functional operation only. Wider typical pulses are recommended to achieve good clamp performance. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS* Parameter AVDD TCVDD HVDD RGVDD DVDD DRVDD RG Output With Respect To AVSS TCVSS HVSS RGVSS DVSS DRVSS RGVSS HVSS DVSS DVSS DVSS AVSS PACKAGE THERMAL CHARACTERISTICS Thermal Resistance JA = 25C/W* Min -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 Max +3.9 +3.9 +3.9 +3.9 +3.9 +3.9 RGVDD + 0.3 HVDD + 0.3 DVDD + 0.3 DVDD + 0.3 DVDD + 0.3 AVDD + 0.3 150 350 Unit V V V V V V V *JA is measured using a 4-layer PCB with the exposed paddle soldered to the board. ORDERING GUIDE Model AD9995KCP AD9995KCPRL Temperature Range -20C to +85C -20C to +85C Package Description LFCSP LFCSP Package Option CP-56 CP-56 H1-H4 Output Digital Outputs Digital Inputs SCK, SL, SDATA REFT, REFB, CCDIN Junction Temperature Lead Temperature, 10 sec V V V V V C C *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute maximum ratings apply individually only, not in combination. Unless otherwise specified, all other voltages are referenced to GND. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9995 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 -5- AD9995 PIN CONFIGURATION 53 D1 52 D0 (LSB) 47 VD 46 SYNC_CLP 45 STROBE 44 MSHUT 51 DCLK 50 HD 49 DVDD 48 DVSS 56 D4 54 D2 43 SCK 55 D3 D5 D6 D7 D8 D9 D10 (MSB) D11 DRVDD DRVSS 1 2 3 4 5 6 7 8 9 PIN 1 IDENTIFIER 42 41 40 39 38 SDI SL REFB REFT AVSS CCDIN AVDD CLI CLO TCVDD TCVSS RGVDD RG RGVSS AD9995 TOP VIEW 37 36 35 34 33 32 31 30 29 VSUB 10 SUBCK 11 V1 12 V2 13 V3 14 VSG3 20 V6 17 VSG1 18 VSG2 19 VSG4 21 V4 15 V5 16 H1 23 HVSS 25 VSG5 22 H2 24 HVDD 26 H3 27 PIN FUNCTION DESCRIPTIONS1 H4 28 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Mnemonic D5 D6 D7 D8 D9 D10 D11 DRVDD DRVSS VSUB SUBCK V1 V2 V3 V4 V5 V6 VSG1 VSG2 VSG3 VSG4 VSG5 H1 H2 HVSS HVDD H3 H4 RGVSS RG RGVDD TCVSS TCVDD CLO CLI Type2 DO DO DO DO DO DO DO P P DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO P P DO DO P DO P P P DO DI Description Data Output Data Output Data Output Data Output Data Output Data Output Data Output (MSB) Data Output Driver Supply Data Output Driver Ground CCD Substrate Bias CCD Substrate Clock (E-Shutter) CCD Vertical Transfer Clock 1 CCD Vertical Transfer Clock 2 CCD Vertical Transfer Clock 3 CCD Vertical Transfer Clock 4 CCD Vertical Transfer Clock 5 CCD Vertical Transfer Clock 6 CCD Sensor Gate Pulse 1 CCD Sensor Gate Pulse 2 CCD Sensor Gate Pulse 3 CCD Sensor Gate Pulse 4 CCD Sensor Gate Pulse 5 CCD Horizontal Clock 1 CCD Horizontal Clock 2 H1-H4 Driver Ground H1-H4 Driver Supply CCD Horizontal Clock 3 CCD Horizontal Clock 4 RG Driver Ground CCD Reset Gate Clock RG Driver Supply Analog Ground for Timing Core Analog Supply for Timing Core Clock Output for Crystal Reference Clock Input -6- Pin 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Mnemonic AVDD CCDIN AVSS REFT REFB SL SDI SCK MSHUT STROBE SYNC VD DVSS DVDD HD DCLK D0 D1 D2 D3 D4 Type2 P AI P AO AO DI DI DI DO DO DI DIO P P DIO DO DO DO DO DO DO Description Analog Supply for AFE CCD Signal Input Analog Ground for AFE Voltage Reference Top Bypass Voltage Reference Bottom Bypass 3-Wire Serial Load Pulse 3-Wire Serial Data Input 3-Wire Serial Clock Mechanical Shutter Pulse Strobe Pulse External System Sync Input Vertical Sync Pulse (Input for Slave Mode, Output for Master Mode) Digital Ground Power Supply for VSG, V1-V6, HD/VD, MSHUT, STROBE, SYNC, and Serial Interface Horizontal Sync Pulse (Input for Slave Mode, Output for Master Mode) Data Clock Output Data Output (LSB) Data Output Data Output Data Output Data Output NOTES 1See Figure 38 for circuit configuration. 2AI = Analog Input, AO = Analog Output, DI = Digital Input, DO = Digital Output, DIO = Digital Input/Output, P = Power. REV. 0 AD9995 TERMINOLOGY Differential Nonlinearity (DNL) An ideal ADC exhibits code transitions that are exactly 1 LSB apart. DNL is the deviation from this ideal value. Therefore, every code must have a finite width. No missing codes guaranteed to 12-bit resolution indicates that all 4096 codes must be present over all operating conditions. Peak Nonlinearity age of the 2 V ADC full-scale signal. The input signal is always appropriately gained up to fill the ADC's full-scale range. Total Output Noise Peak nonlinearity, a full signal chain specification, refers to the peak deviation of the output of the AD9995 from a true straight line. The point used as zero scale occurs 0.5 LSB before the first code transition. Positive full scale is defined as a level 1.5 LSB beyond the last code transition. The deviation is measured from the middle of each particular output code to the true straight line. The error is then expressed as a percentEQUIVALENT CIRCUITS The rms output noise is measured using histogram techniques. The standard deviation of the ADC output codes is calculated in LSB and represents the rms noise level of the total signal chain at the specified gain setting. The output noise can be converted to an equivalent voltage using the relationship 1 LSB = (ADC Full Scale/2n codes), where n is the bit resolution of the ADC. For the AD9995, 1 LSB is 0.488 mV. Power Supply Rejection (PSR) The PSR is measured with a step change applied to the supply pins. The PSR specification is calculated from the change in the data outputs for a given step change in the supply voltage. DVDD AVDD R AVSS AVSS DVSS Circuit 1. CCDIN Circuit 3. Digital Inputs HVDD OR RGVDD DVDD DRVDD RG, H1-H4 DATA THREESTATE DOUT ENABLE OUTPUT DVSS DRVSS HVSS OR RGVSS Circuit 2. Digital Data Outputs Circuit 4. H1-H4, RG Drivers REV. 0 -7- AD9995-Typical Performance Characteristics 450 48 400 POWER DISSIPATION (mW) VDD = 3.3V OUTPUT NOISE (LSB) 36 VDD = 3.0V 40 350 32 300 VDD = 2.7V 250 24 16 200 8 150 18 24 30 0 0 200 400 600 800 1000 SAMPLE RATE (MHz) VGA GAIN CODE (LSB) TPC 1. Power Dissipation vs. Sample Rate 1.0 TPC 3. Output Noise vs. VGA Gain 0.5 DNL (LSB) 0 -0.5 -1.0 0 500 1000 1500 2000 CODES 2500 3000 3500 4000 TPC 2. Typical DNL Performance -8- REV. 0 AD9995 SYSTEM OVERVIEW Figure 1 shows the typical system block diagram for the AD9995 used in Master mode. The CCD output is processed by the AD9995's AFE circuitry, which consists of a CDS, VGA, black level clamp, and A/D converter. The digitized pixel information is sent to the digital image processor chip, which performs the postprocessing and compression. To operate the CCD, all CCD timing parameters are programmed into the AD9995 from the system microprocessor through the 3-wire serial interface. From the system master clock, CLI, provided by the image processor or external crystal, the AD9995 generates all of the CCD's horizontal and vertical clocks and all internal AFE clocks. External synchronization is provided by a SYNC pulse from the microprocessor, which will reset internal counters and resync the VD and HD outputs. Alternatively, the AD9995 may be operated in Slave mode, in which VD and HD are provided externally from the image processor. In this mode, all AD9995 timing will be synchronized with VD and HD. V-DRIVER V1-V6, VSG1-VSG5, SUBCK The H-drivers for H1-H4 and RG are included in the AD9995, allowing these clocks to be directly connected to the CCD. H-drive voltage of up to 3.3 V is supported. An external V-driver is required for the vertical transfer clocks, the sensor gate pulses, and the substrate clock. The AD9995 also includes programmable MSHUT and STROBE outputs, which may be used to trigger mechanical shutter and strobe (flash) circuitry. Figures 2 and 3 show the maximum horizontal and vertical counter dimensions for the AD9995. All internal horizontal and vertical clocking is controlled by these counters to specify line and pixel locations. Maximum HD length is 4095 pixels per line, and maximum VD length is 4095 lines per field. MAXIMUM FIELD DIMENSIONS 12-BIT HORIZONTAL = 4096 PIXELS MAX H1-H4, RG, VSUB DOUT CCD CCDIN MSHUT STROBE SYNC AD9995 AFETG DCLK HD, VD CLI DIGITAL IMAGE PROCESSING ASIC 12-BIT VERTICAL = 4096 LINES MAX SERIAL INTERFACE Figure 2. Vertical and Horizontal Counters Figure 1. Typical System Block Diagram, Master Mode MAX VD LENGTH IS 4095 LINES VD MAX HD LENGTH IS 4095 PIXELS HD CLI Figure 3. Maximum VD/HD Dimensions REV. 0 -9- AD9995 PRECISION TIMING HIGH SPEED TIMING GENERATION The AD9995 generates high speed timing signals using the flexible Precision Timing core. This core is the foundation for generating the timing used for both the CCD and the AFE: the reset gate RG, horizontal drivers H1-H4, and SHP/SHD sample clocks. A unique architecture makes it routine for the system designer to optimize image quality by providing precise control over the horizontal CCD readout and the AFE correlated double sampling. The high speed timing of the AD9995 operates the same in either Master or Slave mode configuration. For more information on synchronization and pipeline delays, see the Power-Up and Synchronization section. Timing Resolution CLIDIVIDE register (Addr. 0x30). The AD9995 will then internally divide the CLI frequency by 2. The AD9995 also includes a master clock output, CLO, which is the inverse of CLI. This output is intended to be used as a crystal driver. A crystal can be placed between the CLI and CLO pins to generate the master clock for the AD9995. For more information on using a crystal, see Figure 39. High Speed Clock Programmability The Precision Timing core uses a 1 master clock input (CLI) as a reference. This clock should be the same as the CCD pixel clock frequency. Figure 4 illustrates how the internal timing core divides the master clock period into 48 steps or edge positions. Using a 20 MHz CLI frequency, the edge resolution of the Precision Timing core is 1 ns. If a 1 system clock is not available, it is also possible to use a 2 reference clock by programming the POSITION CLI P[0] P[12] Figure 5 shows how the high speed clocks RG, H1-H4, SHP, and SHD are generated. The RG pulse has programmable rising and falling edges, and may be inverted using the polarity control. The horizontal clocks H1 and H3 have programmable rising and falling edges and polarity control. The H2 and H4 clocks are always inverses of H1 and H3, respectively. Table I summarizes the high speed timing registers and their parameters. Figure 6 shows the typical 2-phase H-clock arrangement in which H3 and H4 are programmed for the same edge location as H1 and H2. The edge location registers are 6 bits wide, but there are only 48 valid edge locations available. Therefore, the register values are P[24] P[36] P[48] = P[0] tCLIDLY 1 PIXEL PERIOD NOTES PIXEL CLOCK PERIOD IS DIVIDED INTO 48 POSITIONS, PROVIDING FINE EDGE RESOLUTION FOR HIGH SPEED CLOCKS. THERE IS A FIXED DELAY FROM THE CLI INPUT TO THE INTERNAL PIXEL PERIOD POSITIONS (tCLIDLY = 6ns TYP). Figure 4. High Speed Clock Resolution from CLI Master Clock Input 3 CCD SIGNAL 1 RG 5 H1 6 2 4 H2 7 H3 8 H4 PROGRAMMABLE CLOCK POSITIONS: 1. RG RISING EDGE 2. RG FALLING EDGE 3. SHP SAMPLE LOCATION 4. SHD SAMPLE LOCATION 5. H1 RISING EDGE POSITION 6. H1 FALLING EDGE POSITION (H2 IS INVERSE OF H1) 7. H3 RISING EDGE POSITION 8. H3 FALLING EDGE POSITION (H4 IS INVERSE OF H3) Figure 5. High Speed Clock Programmable Locations -10- REV. 0 AD9995 mapped into four quadrants, with each quadrant containing 12 edge locations. Table II shows the correct register values for the corresponding edge locations. Figure 7 shows the default timing locations for all of the high speed clock signals. H-Driver and RG Outputs Digital Data Outputs In addition to the programmable timing positions, the AD9995 features on-chip output drivers for the RG and H1-H4 outputs. These drivers are powerful enough to directly drive the CCD inputs. The H-driver and RG current can be adjusted for optimum rise/fall time into a particular load by using the DRVCONTROL register (Addr. 0x35). The 3-bit drive setting for each output is adjustable in 4.1 mA increments, with the minimum setting of 0 equal to OFF or three-state, and the maximum setting of 7 equal to 30.1 mA. As shown in Figures 5, 6, and 7, the H2 and H4 outputs are inverses of H1 and H3, respectively. The H1/H2 crossover voltage is approximately 50% of the output swing. The crossover voltage is not programmable. The AD9995 data output and DCLK phases are programmable using the DOUTPHASE register (Addr. 0x37, Bits [5:0]). Any edge from 0 to 47 may be programmed, as shown in Figure 8a. Normally, the DOUT and DCLK signals will track in phase based on the DOUTPHASE register contents. The DCLK output phase can also be held fixed with respect to the data outputs by changing the DCLKMODE register high (Addr. 0x37, Bit 6). In this mode, the DCLK output will remain at a fixed phase equal to CLO (the inverse of CLI) while the data output phase is still programmable. There is a fixed output delay from the DCLK rising edge to the DOUT transition, called tOD. This delay can be programmed to four values between 0 ns and 12 ns by using the DOUTDELAY register (Addr. 0x037, Bits [8:7]). The default value is 8 ns. The pipeline delay through the AD9995 is shown in Figure 8b. After the CCD input is sampled by SHD, there is an 11-cycle delay until the data is available. Table I. Timing Core Register Parameters for H1, H3, RG, SHP/SHD Parameter Polarity Positive Edge Negative Edge Sampling Location Drive Strength Length 1b 6b 6b 6b 3b Range High/Low 0-47 Edge Location 0-47 Edge Location 0-47 Edge Location 0-47 Current Steps Description Polarity Control for H1, H3, and RG (0 = No Inversion, 1 = Inversion) Positive Edge Location for H1, H3, and RG Negative Edge Location for H1, H3, and RG Sampling Location for Internal SHP and SHD Signals Drive Current for H1-H4 and RG Outputs (4.1 mA per Step) CCD SIGNAL RG H1/H3 H2/H4 USING THE SAME TOGGLE POSITIONS FOR H1 AND H3 GENERATES STANDARD 2-PHASE H-CLOCKING. Figure 6. 2-Phase H-Clock Operation Table II. Precision Timing Edge Locations Quadrant I II III IV Edge Location (Dec) 0 to 11 12 to 23 24 to 35 36 to 47 Register Value (Dec) 0 to 11 16 to 27 32 to 43 48 to 59 Register Value (Bin) 000000 to 001011 010000 to 011011 100000 to 101011 110000 to 111011 REV. 0 -11- AD9995 POSITION P[0] P[12] P[24] P[36] P[48] = P[0] PIXEL PERIOD RGr[0] RG Hr[0] H1/H3 Hf[24] RGf[12] H2/H4 SHP[24] CCD SIGNAL tS1 SHD[0] NOTES ALL SIGNAL EDGES ARE FULLY PROGRAMMABLE TO ANY OF THE 48 POSITIONS WITHIN ONE PIXEL PERIOD. DEFAULT POSITIONS FOR EACH SIGNAL ARE SHOWN. Figure 7. High Speed Timing Default Locations P[0] P[12] P[24] P[36] P[48] = P[0] PIXEL PERIOD DCLK tOD DOUT NOTES DATA OUTPUT (DOUT) AND DCLK PHASE ARE ADJUSTABLE WITH RESPECT TO THE PIXEL PERIOD. WITHIN ONE CLOCK PERIOD, THE DATA TRANSITION CAN BE PROGRAMMED TO 48 DIFFERENT LOCATIONS. OUTPUT DELAY (tOD) FROM DCLK RISING EDGE TO DOUT RISING EDGE IS PROGRAMMABLE. Figure 8a. Digital Output Phase Adjustment CLI tCLIDLY N-1 CCDIN SAMPLE PIXEL N SHD (INTERNAL) N N+1 N+2 N+3 N+4 N+5 N+6 N+7 N+8 N+9 N+10 N+11 N+12 N+13 DCLK PIPELINE LATENCY=11 CYCLES DOUT N-13 N-12 N-11 N-10 N-9 N-8 N-7 N-6 N-5 N-4 N-3 N-2 N-1 N N+1 N+2 NOTES DEFAULT TIMING VALUES ARE SHOWN: SHDLOC = 0, DOUT PHASE = 0, DCLKMODE = 0. HIGHER VALUES OF SHD AND/OR DOUTPHASE WILL SHIFT DOUT TRANSITION TO THE RIGHT, WITH RESPECT TO CLI LOCATION. Figure 8b. Pipeline Delay -12- REV. 0 AD9995 HORIZONTAL CLAMPING AND BLANKING The AD9995's horizontal clamping and blanking pulses are fully programmable to suit a variety of applications. Individual control is provided for CLPOB, PBLK, and HBLK during the different regions of each field. This allows the dark pixel clamping and blanking patterns to be changed at each stage of the readout in order to accommodate different image transfer timing and high speed line shifts. Individual CLPOB and PBLK Patterns each containing a unique pulse pattern for CLPOB and PBLK. Figure 9 shows how the sequence change positions divide the readout field into different regions. A different V-sequence can be assigned to each region, allowing the CLPOB and PBLK signals to be changed accordingly with each change in the vertical timing. Individual HBLK Patterns The AFE horizontal timing consists of CLPOB and PBLK, as shown in Figure 9. These two signals are independently programmed using the registers in Table III. SPOL is the start polarity for the signal, and TOG1 and TOG2 are the first and second toggle positions of the pulse. Both signals are active low and should be programmed accordingly. A separate pattern for CLPOB and PBLK may be programmed for every 10 V-sequences. As described in the Vertical Timing Generation section, up to 10 separate V-sequences can be created, The HBLK programmable timing shown in Figure 10 is similar to CLPOB and PBLK. However, there is no start polarity control. Only the toggle positions are used to designate the start and stop positions of the blanking period. Additionally, there is a polarity control HBLKMASK that designates the polarity of the horizontal clock signals H1-H4 during the blanking period. Setting HBLKMASK high will set H1 = H3 = low and H2 = H4 = high during the blanking, as shown in Figure 11. As with the CLPOB and PBLK signals, HBLK registers are available in each V-sequence, allowing different blanking signals to be used with different vertical timing sequences. ... HD CLPOB (1) PBLK ACTIVE ACTIVE NOTES PROGRAMMABLE SETTINGS: 1. START POLARITY (CLAMP AND BLANK REGION ARE ACTIVE LOW) 2. FIRST TOGGLE POSITION 3. SECOND TOGGLE POSITION Figure 9. Clamp and Pre-Blank Pulse Placement Table III. CLPOB and PBLK Pattern Registers Register SPOL TOG1 TOG2 Length 1b 12b 12b Range High/Low 0-4095 Pixel Location 0-4095 Pixel Location Description Starting Polarity of CLPOB/PBLK for V-Sequence 0-9 First Toggle Position within Line for V-Sequence 0-9 Second Toggle Position within Line for V-Sequence 0-9 Table IV. HBLK Pattern Registers Register HBLKMASK HBLKALT HBLKTOG1 HBLKTOG2 HBLKTOG3 HBLKTOG4 HBLKTOG5 HBLKTOG6 Length 1b 2b 12b 12b 12b 12b 12b 12b Range High/Low 0-3 Alternation Mode 0-4095 Pixel Location 0-4095 Pixel Location 0-4095 Pixel Location 0-4095 Pixel Location 0-4095 Pixel Location 0-4095 Pixel Location Description Masking Polarity for H1/H3 (0 = H1/H3 Low, 1 = H1/H3 High) Enables Odd/Even Alternation of HBLK Toggle Positions 0 = Disable Alternation. 1 = TOG1-TOG2 Odd, TOG3-TOG6 Even. 2 = 3 = TOG1-TOG2 Even, TOG3-TOG6 Odd First Toggle Position within Line for Each V-Sequence 0-9 Second Toggle Position within Line for Each V-Sequence 0-9 Third Toggle Position within Line for Each V-Sequence 0-9 Fourth Toggle Position within Line for Each V-Sequence 0-9 Fifth Toggle Position within Line for Each V-Sequence 0-9 Sixth Toggle Position within Line for Each V-Sequence 0-9 REV. 0 -13- ... (2) (3) AD9995 Generating Special HBLK Patterns Generating HBLK Line Alternation There are six toggle positions available for HBLK. Normally, only two of the toggle positions are used to generate the standard HBLK interval. However, the additional toggle positions may be used to generate special HBLK patterns, as shown in Figure 12. The pattern in this example uses all six toggle positions to generate two extra groups of pulses during the HBLK interval. By changing the toggle positions, different patterns can be created. One further feature of the AD9995 is the ability to alternate different HBLK toggle positions on odd and even lines. This may be used in conjunction with V-pattern odd/even alternation or on its own. When a 1 is written to the HBLKALT register, TOG1 and TOG2 are used on odd lines only, while TOG3-TOG6 are used on even lines. Writing a 2 to the HBLKALT register gives the opposite result: TOG1 and TOG2 are used on even lines, while TOG3-TOG6 are used on odd lines. See the Vertical Timing Generation, Line Alternation section for more information. HD 1 HBLK BLANK 2 BLANK PROGRAMMABLE SETTINGS: 1. FIRST TOGGLE POSITION = START OF BLANKING 2. SECOND TOGGLE POSITION = END OF BLANKING Figure 10. Horizontal Blanking (HBLK) Pulse Placement HD HBLK H1/H3 H1/H3 H2/H4 THE POLARITY OF H1 DURING BLANKING IS PROGRAMMABLE (H2 IS OPPOSITE POLARITY OF H1). Figure 11. HBLK Masking Control TOG1 TOG2 TOG3 TOG4 TOG5 TOG6 HBLK H1/H3 H2/H4 SPECIAL H-BLANK PATTERN IS CREATED USING MULTIPLE HBLK TOGGLE POSITIONS. Figure 12. Generating Special HBLK Patterns -14- REV. 0 AD9995 HORIZONTAL TIMING SEQUENCE EXAMPLE Figure 13 shows an example CCD layout. The horizontal register contains 28 dummy pixels, which will occur on each line clocked from the CCD. In the vertical direction, there are 10 optical black (OB) lines at the front of the readout and two at the back of the readout. The horizontal direction has four OB pixels in the front and 48 in the back. Figure 14 shows the basic sequence layout to be used during the effective pixel readout. The 48 OB pixels at the end of each line are used for the CLPOB signals. PBLK is optional and is often used to blank the digital outputs during the noneffective CCD pixels. HBLK is used during the vertical shift interval. The HBLK, CLPOB, and PBLK parameters are programmed in the V-sequence registers. More elaborate clamping schemes may be used, such as adding in a separate sequence to clamp during the entire shield OB lines. This requires configuring a separate V-sequence for reading out the OB lines. 2 VERTICAL OB LINES V EFFECTIVE IMAGE AREA 10 VERTICAL OB LINES H 4 OB PIXELS HORIZONTAL CCD REGISTER 48 OB PIXELS 28 DUMMY PIXELS Figure 13. Example CCD Configuration HD OB CCDIN OPTICAL BLACK VERTICAL SHIFT DUMMY EFFECTIVE PIXELS OPTICAL BLACK VERT SHIFT SHP SHD H1/H3 H2/H HBLK PBLK CLPOB Figure 14. Horizontal Sequence Example REV. 0 -15- AD9995 VERTICAL TIMING GENERATION The AD9995 provides a very flexible solution for generating vertical CCD timing, and can support multiple CCDs and different system architectures. The 6-phase vertical transfer clocks V1-V6 are used to shift each line of pixels into the horizontal output register of the CCD. The AD9995 allows these outputs to be individually programmed into various readout configurations using a 4-step process. Figure 15 shows an overview of how the vertical timing is generated in four steps. First, the individual pulse patterns for V1-V6 CREATE THE VERTICAL PATTERN GROUPS (MAXIMUM OF 10 GROUPS). V1 V2 VPAT 0 V3 V4 V5 V6 are created by using the vertical pattern group registers. Second, the V-pattern groups are used to build the sequences, where additional information is added. Third, the readout for an entire field is constructed by dividing the field into different regions and then assigning a sequence to each region. Each field can contain up to seven different regions to accommodate different steps of the readout such as high speed line shifts and unique vertical line transfers. Up to six different fields may be created. Finally, the Mode register allows the different fields to be combined into any order for various readout configurations. BUILD THE V-SEQUENCES BY ADDING LINE START POSITION, # OF REPEATS, AND HBLK/CLPOB PULSES (MAXIMUM OF 10 V-SEQUENCES). V1 V2 V-SEQUENCE 0 (VPAT0, 1 REP) V3 V4 V5 V6 V1 V1 V2 V3 VPAT 9 V4 V5 V6 V-SEQUENCE 1 (VPAT9, 2 REP) V2 V3 V4 V5 V6 V1 V2 V-SEQUENCE 2 (VPAT9, N REP) V3 V4 V5 V6 USE THE MODE REGISTER TO CONTROL WHICH FIELDS ARE USED, AND IN WHAT ORDER (MAXIMUM OF 7 FIELDS MAY BE COMBINED IN ANY ORDER). BUILD EACH FIELD BY DIVIDING INTO DIFFERENT REGIONS, AND ASSIGNING A DIFFERENT V-SEQUENCE TO EACH (MAXIMUM OF 7 REGIONS IN EACH FIELD) (MAXIMUM OF 6 FIELDS). FIELD 0 REGION 0: USE V-SEQUENCE 2 REGION 0: USE V-SEQUENCE 3 REGION 1: USE V-SEQUENCE 0 REGION 0: USE V-SEQUENCE 3 REGION 2: USE USE V-SEQUENCE 2 REGION 1: V-SEQUENCE 3 REGION 1: USE V-SEQUENCE 2 FIELD 0 FIELD 1 FIELD 2 FIELD 3 FIELD 4 REGION 3: USE V-SEQUENCE 0 REGION 2: USE V-SEQUENCE 1 FIELD 5 FIELD 1 FIELD 4 FIELD 2 REGION 2: USE V-SEQUENCE 1 REGION 4: USE V-SEQUENCE 2 FIELD 1 FIELD 2 Figure 15. Summary of Vertical Timing Generation -16- REV. 0 AD9995 Vertical Pattern Groups (VPAT) The vertical pattern groups define the individual pulse patterns for each V1-V6 output signal. Table V summarizes the registers available for generating each of the 10 V-pattern groups. The start polarity (VPOL) determines the starting polarity of the vertical sequence, and can be programmed high or low for each V1-V6 output. The first, second, and third toggle position (VTOG1, VTOG2, VTOG3) are the pixel locations within the line where the pulse transitions. A fourth toggle position (VTOG4) is also available for V-Pattern Groups 8 and 9. All toggle positions are 12-bit values, allowing their placement anywhere in the horizontal line. A separate register, VPATSTART, specifies the start position of the V-pattern group within the line (see the Vertical Sequences section). The VPATLEN register designates the total length of the V-pattern group, which will determine the number of pixels between each of the pattern repetitions, when repetitions are used (see the Vertical Sequences section). The FREEZE and RESUME registers are used to temporarily stop the operation of the V1-V6 outputs. At the pixel location specified in the FREEZE register, the V1-V6 outputs will be held static at their current dc state, high or low. The V1-V6 outputs are held until the pixel location specified by RESUME register. Two sets of FREEZE/RESUME registers are provided, allowing the vertical outputs to be interrupted twice in the same line. The FREEZE and RESUME positions are programmed in the V-pattern group registers, but are separately enabled using the VMASK registers, which are described in the Vertical Sequence section. Table V. Vertical Pattern Group Registers Register VPOL VTOG1 VTOG2 VTOG3 VTOG4 VPATLEN FREEZE1 RESUME1 FREEZE2 RESUME2 Length 1b 12b 12b 12b 12b 12b 12b 12b 12b 12b Range High/Low 0-4096 Pixel Location 0-4096 Pixel Location 0-4096 Pixel Location 0-4096 Pixel Location 0-4096 Pixels 0-4096 Pixel Location 0-4096 Pixel Location 0-4096 Pixel Location 0-4096 Pixel Location Description Starting Polarity of Each V1-V6 Output First Toggle Position within Line for Each V1-V6 Output Second Toggle Position within Line for Each V1-V6 Output Third Toggle Position within Line for Each V1-V6 Output Fourth Toggle Position, only Available in V-Pattern Groups 8 and 9 Total Length of Each V-Pattern Group Holds the V1-V6 Outputs at Their Current Levels (Static DC) Resumes Operation of the V1-V6 Outputs to Finish Their Pattern Holds the V1-V6 Outputs at Their Current Levels (Static DC) Resumes Operation of the V1-V6 Outputs to Finish Their Pattern START POSITION OF V-PATTERN GROUP IS PROGRAMMABLE IN V-SEQUENCE REGISTERS HD 4 V1 1 2 3 V2 1 2 3 V6 1 2 3 PROGRAMMABLE SETTINGS FOR EACH V-PATTERN: 1. START POLARITY 2. FIRST TOGGLE POSITION 3. SECOND TOGGLE POSITION (3RD TOGGLE POSITION ALSO AVAILABLE, 4TH TOGGLE POSITION AVAILABLE FOR V-PATTERN GROUPS 8 AND 9) 4. TOTAL PATTERN LENGTH FOR ALL V1-V6 OUTPUTS Figure 16. Vertical Pattern Group Programmability REV. 0 -17- AD9995 Vertical Sequences (VSEQ) The vertical sequences are created by selecting one of the 10 V-pattern groups and adding repeats, start position, and horizontal clamping and blanking information. Up to 10 V-sequences can be programmed, each using the registers shown in Table VI. Figure 17 shows how the different registers are used to generate each V-sequence. The VPATSEL register selects which V-pattern group will be used in a given V-sequence. The basic V-pattern group can have repetitions added, for high speed line shifts or line binning, by using the VPATREPO and VPATREPE registers. Generally, the same number of repetitions are programmed into both registers, but if a different number of repetitions is required on odd and even lines, separate values may be used for each register (see the V-Sequence Line Alternation section). The VPATSTART register specifies where in the line the V-pattern group will start. The VMASK register is used in conjunction with the FREEZE/ RESUME registers to enable optional masking of the V-outputs. Either or both of the FREEZE1/RESUME1 and FREEZE2/ RESUME2 registers can be enabled. The line length (in pixels) is programmable using the HDLEN registers. Each V-sequence can have a different line length to accommodate various image readout techniques. The maximum number of pixels per line is 4096. Note that the last line of the field is separately programmable using the HDLAST register located in the Field register section. Table VI. V-Sequence Registers (see Tables III and IV for HBLK, CLPOB, PBLK Registers) Register VPATSEL VMASK Length 4b 2b Range 0-9 V-Pattern Group # 0-3 Mask Mode Description Selected V-Pattern Group for Each V-Sequence. Enables the Masking of V1-V6 Outputs at the Locations Specified by the FREEZE/RESUME Registers. 0 = No Mask, 1 = Enable FREEZE1/RESUME1, 2 = Enable FREEZE2/RESUME2, 3 = Enable both 1 and 2. Number of Repetitions for the V-Pattern Group for Odd Lines. If no odd/even alternation is required, set to VPATREPE. Number of Repetitions for the V-Pattern Group for Even Lines. If no odd/even alternation is required, set to VPATREPO. Start Position for the Selected V-Pattern Group. HD Line Length for Lines in Each V-Sequence. VPATREPO VPATREPE VPATSTART HDLEN 12b 12b 12b 12b 0-4095 # of Repeats 0-4095 # of Repeats 0-4095 Pixel Location 0-4095 # of Pixels 1 HD 2 3 V1-V6 V-PATTERN GROUP 4 VPAT REP 2 4 VPAT REP 3 CLPOB PBLK 6 5 HBLK PROGRAMMABLE SETTINGS FOR EACH V-SEQUENCE: 1. START POSITION IN THE LINE OF SELECTED V-PATTERN GROUP 2. HD LINE LENGTH 3. V-PATTERN SELECT (VPATSEL) TO SELECT ANY V-PATTERN GROUP 4. NUMBER OF REPETITIONS OF THE V-PATTERN GROUP (IF NEEDED) 5. START POLARITY AND TOGGLE POSITIONS FOR CLPOB AND PBLK SIGNALS 6. MASKING POLARITY AND TOGGLE POSITIONS FOR HBLK SIGNAL Figure 17. V-Sequence Programmability -18- REV. 0 AD9995 Complete Field: Combining V-Sequences After the V-sequences have been created, they are combined to create different readout fields. A field consists of up to seven different regions, and within each region a different V-sequence can be selected. Figure 18 shows how the sequence change positions (SCP) designate the line boundary for each region, and the VSEQSEL registers then select which V-sequence is used during each region. Registers to control the VSG outputs are also included in the Field registers. Table VII summarizes the registers used to create the different fields. Up to six different fields can be preprogrammed using all of the Field registers. The VEQSEL registers, one for each region, select which of the 10 V-sequences will be active during each region. The SWEEP registers are used to enable SWEEP mode during any region. The MULTI registers are used to enable Multiplier mode dur- ing any region. The SCP registers create the line boundaries for each region. The VDLEN register specifies the total number of lines in the field. The total number of pixels per line (HDLEN) is specified in the V-sequence registers, but the HDLAST register specifies the number of pixels in the last line of the field. The VPATSECOND register is used to add a second V-pattern group to the V1-6 outputs during the sensor gate (VSG) line. The SGMASK register is used to enable or disable each individual VSG output. There is a single bit for each VSG output; setting the bit high will mask the output, setting it low will enable the output. The SGPAT register assigns one of the four different SG patterns to each VSG output. The individual SG patterns are created separately using the SG pattern registers. The SGLINE1 register specifies which line in the field will contain the VSG outputs. The optional SGLINE2 register allows the same VSG pulses to be repeated on a different line. Table VII. Field Registers Register VSEQSEL SWEEP MULTI SCP VDLEN HDLAST VPATSECOND SGMASK SGPATSEL SGLINE1 SGLINE2 Length 4b 1b 1b 12b 12b 12b 4b 6b 12b 12b 12b Range 0-9 V-Sequence # High/Low High/Low 0-4095 Line # 0-4095 # of Lines 0-4095 # of Pixels 0-9 V-Pattern Group # High/Low, Each VSG 0-3 Pattern #, Each VSG 0-4095 Line # 0-4095 Line # Description Selected V-Sequence for Each Region in the Field. Enables Sweep Mode for Each Region, When Set High. Enables Multiplier Mode for Each Region, When Set High. Sequence Change Position for Each Region. Total Number of Lines in Each Field. Length in Pixels of the Last HD Line in Each Field. Selected V-Pattern Group for Second Pattern Applied During VSG Line. Set High to Mask Each Individual VSG Output. VSG1 [0], VSG2 [1], VSG3 [2], VSG4 [3], VSG5 [4]. Selects the VSG Pattern Number for Each VSG Output. VSG1 [1:0], VSG2 [3:2], VSG3 [5:4], VSG4 [7:6], VSG5 [9:8]. Selects the Line in the Field where the VSG Are Active. Selects a Second Line in the Field to Repeat the VSG Signals. SCP 1 SCP 2 SCP 3 SCP 4 SCP 5 SCP 6 VD REGION 0 HD REGION 1 REGION 2 REGION 3 REGION 4 REGION 5 REGION 6 V1-V6 VSEQSEL0 VSEQSEL1 SGLINE1 SGLINE VSEQSEL2 VSEQSEL3 VSEQSEL4 VSEQSEL5 VSEQSEL6 VSG FIELD SETTINGS: 1. SEQUENCE CHANGE POSITIONS (SCP1-6) DEFINE EACH OF THE 7 REGIONS IN THE FIELD. 2. VSEQSEL0-6 SELECTS THE DESIRED V-SEQUENCE (0-9) FOR EACH REGION. 3. SGLINE1 REGISTER SELECTS WHICH HD LINE IN THE FIELD WILL CONTAIN THE SENSOR GATE PULSE(S). Figure 18. Complete Field Is Divided into Regions REV. 0 -19- AD9995 Generating Line Alternation for V-Sequence and HBLK Second V-Pattern Group during VSG Active Line During low resolution readout, some CCDs require a different number of vertical clocks on alternate lines. The AD9995 can support this by using the VPATREPO and VPATREPE registers. This allows a different number of VPAT repetitions to be programmed on odd and even lines. Note that only the number of repeats can be different in odd and even lines, but the VPAT group remains the same. Additionally, the HBLK signal can also be alternated for odd and even lines. When the HBLKALT register is set high, the HBLK TOG1 and TOG2 positions will be used on odd lines and the TOG3-TOG6 positions will be used on even lines. This allows the HBLK interval to be adjusted on odd and even lines if needed. Figure 19 shows an example of VPAT repetition alternation and HBLK alternation used together. It is also possible to use VPAT and HBLK alternation separately. Most CCDs require additional vertical timing during the sensor gate line. The AD9995 supports the option to output a second V-pattern group for V1-V6 during the line when the sensor gates VSG1-VSG5 are active. Figure 20 shows a typical VSG line, which includes two separate sets of V-pattern groups for V1-V6. The V-pattern group at the start of the VSG line is selected in the same manner as the other regions, using the appropriate VSEQSEL register. The second V-pattern group, unique to the VSG line, is selected using the VPATSECOND register, located with the Field registers. The start position of the second VPAT group uses the VPATLEN register from the selected VPAT registers. Because the VPATLEN register is used as the start position and not as the VPAT length, it is not possible to program multiple repetitions for the second VPAT group. HD VPATREPO = 2 V1 VPATREPE = 5 VPATREPO = 2 V2 V6 TOG1 HBLK TOG2 TOG3 TOG4 TOG1 TOG2 NOTES 1. THE NUMBER OF REPEATS FOR THE V-PATTERN GROUP MAY BE ALTERNATED ON ODD AND EVEN LINES. 2. THE HBLK TOGGLE POSITIONS MAY BE ALTERNATED BETWEEN ODD AND EVEN LINES IN ORDER TO GENERATE DIFFERENT HBLK PATTERNS FOR ODD/EVEN LINES. Figure 19. Odd/Even Line Alternation of VPAT Repetitions and HBLK Toggle Positions HD START POSITION FOR 2ND VPAT GROUP USES VPATLEN REGISTER VSG V1 V2 V6 2ND VPAT GROUP Figure 20. Example of Second VPAT Group during Sensor Gate Line -20- REV. 0 AD9995 Sweep Mode Operation The AD9995 contains an additional mode of vertical timing operation called Sweep mode. This mode is used to generate a large number of repetitive pulses that span multiple HD lines. One example of where this mode is needed is at the start of the CCD readout operation. At the end of the image exposure but before the image is transferred by the sensor gate pulses, the vertical interline CCD registers should be free of all charge. This can be accomplished by quickly shifting out any charge using a long series of pulses from the V1-V6 outputs. Depending on the vertical resolution of the CCD, up to 2,000 or 3,000 clock cycles will be needed to shift the charge out of each vertical CCD line. This operation will span across multiple HD line lengths. Normally, the AD9995's vertical timing must be contained within one HD line length, but when Sweep mode is enabled, the HD boundaries will be ignored until the region is finished. To enable Sweep mode within any region, program the appropriate SWEEP register to high. Figure 21 shows an example of Sweep mode operation. The number of vertical pulses needed will depend on the vertical resolution of the CCD. The V1-V6 output signals are generated using the V-pattern registers (shown in Table VII). A single pulse is created using the polarity and toggle position registers. The number of repetitions is then programmed to match the number of vertical shifts required by the CCD. Repetitions are programmed in the V-sequence registers using the VPATREP registers. This produces a pulse train of the appropriate length. Normally, the pulse train would be truncated at the end of the HD line length, but with Sweep mode enabled for this region, the HD boundaries will be ignored. In Figure 21, the Sweep region occupies 23 HD lines. After the Sweep mode region is completed, in the next region, normal sequence operation will resume. When using Sweep mode, be sure to set the region boundaries (using the sequence change positions) to the appropriate lines to prevent the Sweep operation from overlapping the next V-sequence. Multiplier Mode To generate very wide vertical timing pulses, a vertical region may be configured into a multiplier region. This mode uses the V-pattern registers in a slightly different manner. Multiplier mode can be used to support unusual CCD timing requirements, such as vertical pulses that are wider than a single HD line length. The start polarity and toggle positions are still used in the same manner as the standard VPAT group programming, but the VPATLEN is used differently. Instead of using the pixel counter (HD counter) to specify the toggle position locations (VTOG1, 2, 3) of the VPAT group, the VPATLEN is multiplied with the VTOG position to allow very long pulses to be generated. To calculate the exact toggle position, counted in pixels after the start position, use the equation Multiplier ModeTogglePosition = VTOG x VPATLEN Because the VTOG register is multiplied by VPATLEN, the resolution of the toggle position placement is reduced. If VPATLEN = 4, the toggle position accuracy is now reduced to 4-pixel steps instead of single pixel steps. Table VIII summarizes how the VPAT group registers are used in Multiplier mode operation. In Multiplier mode, the VPATREPO and VPATREPE registers should always be programmed to the same value as the highest toggle position. VD SCP 1 SCP 2 HD LINE 0 LINE 1 L LINE 2 LINE 24 LINE 25 V1-V6 REGION 0 REGION 1: SWEEP REGION REGION 2 Figure 21. Example of Sweep Region for High Speed Vertical Shift Table VIII. Multiplier Mode Register Parameters Register MULTI VPOL VTOG1 VTOG2 VTOG3 VPATLEN VPATREP Length 1b 1b 12b 12b 12b 10b 12b Range High/Low High/Low 0-4095 Pixel Location 0-4095 Pixel Location 0-4095 Pixel Location 0-1023 Pixels 0-4096 Description High enables Multiplier mode. Starting Polarity of V1-V6 Signal in Each VPAT Group. First Toggle Position for V1-V6 Signal in Each VPAT Group. Second Toggle Position for V1-V6 Signal in Each VPAT Group. Third Toggle Position for V1-V6 Signal in Each VPAT Group. Used as Multiplier Factor for Toggle Position Counter. VPATREPE/VPATREPO should be set to the same value as TOG2 or 3. REV. 0 -21- AD9995 The example shown in Figure 22 illustrates this operation. The first toggle position is 2, and the second toggle position is 9. In non-Multiplier mode, this causes the V-sequence to toggle at pixel 2 and then pixel 9 within a single HD line. However, toggle positions are now multiplied by the VTPLEN = 4, so the first toggle occurs at pixel count 8 and the second toggle occurs at pixel count 36. Sweep mode has also been enabled to allow the toggle positions to cross the HD line boundaries. Vertical Sensor Gate (Shift Gate) Patterns In an interline CCD, the vertical sensor gates (VSG) are used to transfer the pixel charges from the light-sensitive image area into light-shielded vertical registers. From the light-shield vertical registers, the image is then read out line-by-line by using the vertical transfer pulses V1-V6 in conjunction with the high speed horizontal clocks. Table IX contains the summary of the VSG pattern registers. The AD9995 has five VSG outputs, VSG1-VSG5. Each of the outputs can be assigned to one of four programmed patterns by using the SGPATSEL registers. Each pattern is generated in a similar manner as the V-pattern groups, with a programmable start polarity (SGPOL), first toggle position (SGTOG1), and second toggle position (SGTOG2). The active line where the VSG1-VSG5 pulses occur is programmable using the SGLINE1 and SGLINE2 registers. Additionally, any of the VSG1-VSG5 pulses may be individually disabled by using the SGMASK register. The individual masking allows all of the SG patterns to be preprogrammed, and the appropriate pulses for the different fields can be separately enabled. For maximum flexibility, the SGPATSEL, SGMASK, and SGLINE registers are separately programmable for each field. More detail is given in the Complete Field section. START POSITION OF VPAT GROUP IS STILL PROGRAMMED IN THE V-SEQUENCE REGISTERS HD 3 VPATLEN 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 5 4 1 2 3 4 1 2 3 4 1 2 3 41 2 3 5 41 2 3 41 2 3 4 PIXEL NUMBER 1 2 3 45 6 7 8 4 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 4 V1-V6 1 2 2 MULTIPLIER MODE V-PATTERN GROUP PROPERTIES: 1. START POLARITY (ABOVE: STARTPOL = 0) 2. FIRST, SECOND, AND THIRD TOGGLE POSITIONS (ABOVE: VTOG1 = 2, VTOG2 = 9) 3. LENGTH OF VPAT COUNTER (ABOVE: VPATLEN = 4). THIS IS THE MINIMUM RESOLUTION FOR TOGGLE POSITION CHANGES. 4. TOGGLE POSITIONS OCCUR AT LOCATION EQUAL TO (VTOG VPATLEN) 5. IF SWEEP REGION IS ENABLED, THE V-PULSES MAY ALSO CROSS THE HD BOUNDRIES, AS SHOWN ABOVE Figure 22. Example of Multiplier Region for Wide Vertical Pulse Timing Table IX. VSG Pattern Registers (also see Field Registers in Table VII) Register SGPOL SGTOG1 SGTOG2 Length 1b 12b 12b Range High/Low 0-4095 Pixel Location 0-4095 Pixel Location Description Sensor Gate Starting Polarity for SG Pattern 0-3 First Toggle Position for SG Pattern 0-3 Second Toggle Position for SG Pattern 0-3 VD 4 HD VSG PATTERNS 1 2 3 PROGRAMMABLE SETTINGS FOR EACH PATTERN: 1. START POLARITY OF PULSE 2. FIRST TOGGLE POSITION 3. SECOND TOGGLE POSITION 4. ACTIVE LINE FOR VSG PULSES WITHIN THE FIELD (PROGRAMMABLE IN THE FIELD REGISTER, NOT FOR EACH PATTERN) Figure 23. Vertical Sensor Gate Pulse Placement -22- REV. 0 AD9995 MODE Register The MODE register is a single register that selects the field timing of the AD9995. Typically, all of the field, V-sequence, and V-pattern group information is programmed into the AD9995 at startup. During operation, the MODE register allows the user to select any combination of field timing to meet the current requirements of the system. The advantage of using the MODE register in conjunction with preprogrammed timing is that it greatly reduces the system programming requirements during camera operation. Only a few register writes are required when the camera operating mode is changed, rather than having to write in all of the vertical timing information with each camera mode change. A basic still camera application might require five different fields of vertical timing: one for draft mode operation, one for autofocusing, and three for still image readout. All of the register timing information for the five fields would be loaded at startup. Then, during camera operation, the MODE register would select which field timing would be active, depending on how the camera was being used. Table X shows how the MODE register bits are used. The three MSBs, D23-D21, are used to specify how many total fields will be used. Any value from 1 to 7 can be selected using these three bits. The remaining register bits are divided into 3-bit sections to select which of the six fields are used and in which order. Up to seven fields may be used in a single MODE write. The AD9995 will start with the Field timing specified by the first Field bits, and on the next VD will switch to the timing specified by the second Field bits, and so on. After completing the total number of fields specified in Bits D23 to D21, the AD9995 will repeat by starting at the first Field again. This will continue until a new write to the MODE register occurs. Figure 24 shows example MODE register settings for different field configurations. Table X. MODE Register Data Bit Breakdown (D23 = MSB) D23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 D0 Total Number of Fields to Use. 1 = 1st Field Only 7 = All 7 Fields 0 = Invalid 7th Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 6th Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 5th Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 4th Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 3rd Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 2nd Field 0 = Field 0 5 = Field 5 6, 7 = Invalid 1st Field 0 = Field 0 5 = Field 5 6, 7 = Invalid EXAMPLE 1: TOTAL FIELDS = 3, 1ST FIELD = FIELD 0, 2ND FIELD = FIELD 1, 3RD FIELD = FIELD 2 MODE REGISTER CONTENTS = 0x600088 FIELD 0 FIELD 1 FIELD 2 EXAMPLE 2: TOTAL FIELDS = 2, 1ST FIELD = FIELD 3, 2ND FIELD = FIELD 4 MODE REGISTER CONTENTS = 0x400023 FIELD 3 FIELD 4 EXAMPLE 3: TOTAL FIELDS = 4, 1ST FIELD = FIELD 5, 2ND FIELD = FIELD 1, 3RD FIELD = FIELD 4, 4TH FIELD = FIELD 2 MODE REGISTER CONTENTS = 0x80050D FIELD 5 FIELD 1 FIELD 4 FIELD 2 Figure 24. Using the MODE Register to Select Field Timing REV. 0 -23- AD9995 VERTICAL TIMING EXAMPLE To better understand how the AD9995's vertical timing generation is used, consider the example CCD timing chart in Figure 25. This particular example illustrates a CCD using a general 3-field readout technique. As described in the Field section, each readout field should be divided into separate regions to perform each step of the readout. The sequence change positions (SCP) determine the line boundaries for each region, and the VSEQSEL registers will then assign a particular V-sequence to each region. The V-sequences will contain the specific timing information required in each region: V1-V6 pulses (using VPAT groups), HBLK/CLPOB timing, and VSG patterns for the SG active lines. This particular timing example requires four regions for each of the three fields, labeled Region 0, Region 1, Region 2, and Region 3. Because the AD9995 allows up to six individual fields to be programmed, the Field 0, Field 1, and Field 2 registers can be used to meet the requirements of this timing example. The four regions for each field are very similar in this example, but the individual registers for each field allow flexibility to accommodate other timing charts. Region 0 is a high speed vertical shift region. Sweep mode can be used to generate this timing operation, with the desired number of high speed vertical pulses needed to clear any charge from the CCD's vertical registers. Region 1 consists of only two lines, and uses standard single line vertical shift timing. The timing of this region area will be the same as the timing in Region 3. Region 2 is the sensor gate line, where the VSG pulses transfer the image into the vertical CCD registers. This region may require the use of the second V-pattern group for SG active line. Region 3 also uses the standard single line vertical shift timing, the same timing as Region 1. In summary, four regions are required in each of the three fields. The timing for Regions 1 and 3 is essentially the same, reducing the complexity of the register programming. Other registers will need to be used during the actual readout operation, such as the MODE register, shutter control registers (TRIGGER, SUBCK, VSUB, MSHUT, STROBE), and AFE gain register. These registers will be explained in other examples. Important Note about Signal Polarities When programming the AD9995 to generate the V1-V6, VSG1-VSG5, and SUBCK signals, it is important to note that the V-driver circuit usually inverts these signals. Carefully check the required timing signals needed at the input and output of the V-driver circuit being used and adjust the polarities of the AD9995's outputs accordingly. -24- REV. 0 1 4 7 10 13 16 2 5 8 11 14 17 20 n-5 n-2 n-4 n-1 3 6 9 12 15 18 21 Figure 25. CCD Timing Example: Dividing Each Field into Regions CCD OUT REGION 0 REGION 1 FIELD 0 REGION 2 REGION 3 REGION 0 REGION 1 REGION 3 REGION 2 FIELD 1 REGION 0 REGION 1 REGION 3 REGION 2 FIELD 2 n- 3 n REV. 0 SECOND FIELD READOUT THIRD FIELD READOUT CLOSED OPEN EXPOSURE (tEXP) FIRST FIELD READOUT VD HD V1 V2 V3 V4 V5 -25- V6 SUBCK MSHUT OPEN VSUB AD9995 AD9995 SHUTTER TIMING CONTROL High Precision Shutter Operation The CCD image exposure time is controlled by the substrate clock signal (SUBCK), which pulses the CCD substrate to clear out accumulated charge. The AD9995 supports three types of electronic shuttering: normal shutter, high precision shutter, and low speed shutter. Along with the SUBCK pulse placement, the AD9995 can accommodate different readout configurations to further suppress the SUBCK pulses during multiple field readouts. The AD9995 also provides programmable outputs to control an external mechanical shutter (MSHUT), strobe/flash (STROBE), and the CCD bias select signal (VSUB). Normal Shutter Operation High precision shuttering is used in the same manner as normal shuttering, but uses an additional register to control the very last SUBCK pulse. In this mode, the SUBCK still pulses once per line, but the last SUBCK in the field will have an additional SUBCK pulse whose location is determined by the SUBCK2TOG register, as shown in Figure 27. Finer resolution of the exposure time is possible using this mode. Leaving the SUBCK2TOG register set to max value (0xFFFFFF) will disable the last SUBCK pulse (default setting). Low Speed Shutter Operation By default, the AD9995 is always operating in the normal shutter configuration in which the SUBCK signal is pulsing in every VD field (see Figure 26). The SUBCK pulse occurs once per line, and the total number of repetitions within the field will determine the length of the exposure time. The SUBCK pulse polarity and toggle positions within a line are programmable using the SUBCKPOL and SUBCK1TOG registers (see Table XI). The number of SUBCK pulses per field is programmed in the SUBCKNUM register (Addr. 0x63). As shown in Figure 26, the SUBCK pulses will always begin in the line following the SG active line, which is specified in the SGACTLINE registers for each field. The SUBCKPOL, SUBCK1TOG, SUBCK2TOG, SUBCKNUM, and SUBCKSUPPRESS registers are updated at the start of the line after the sensor gate line, as described in the Updating New Register Values section. Normal and high precision shutter operations are used when the exposure time is less than one field long. For long exposure times greater than one field interval, low speed shutter operation is used. The AD9995 uses a separate exposure counter to achieve long exposure times. The number of fields for the low speed shutter operation is specified in the EXPOSURE register (Addr. 0x62). As shown in Figure 28, this shutter mode will suppress the SUBCK and VSG outputs for up to 4095 fields (VD periods). The VD and HD outputs may be suppressed during the exposure period by programming the VDHDOFF register to 1. To generate a low speed shutter operation, it is necessary to trigger the start of the long exposure by writing to the TRIGGER register bit D3. When this bit is set high, the AD9995 will begin an exposure operation at the next VD edge. If a value greater than zero is specified in the EXPOSURE register, the AD9995 will suppress the SUBCK output on subsequent fields. VD HD VSG tEXP tEXP SUBCK SUBCK PROGRAMMABLE SETTINGS: 1. PULSE POLARITY USING THE SUBCKPOL REGISTER. 2. NUMBER OF PULSES WITHIN THE FIELD USING THE SUBCKNUM REGISTER (SUBCKNUM = 3 IN THE ABOVE FIGURE). 3. PIXEL LOCATION OF PULSE WITHIN THE LINE AND PULSEWIDTH PROGRAMMED USING SUBCK1 TOGGLE POSITION REGISTER. Figure 26. Normal Shutter Mode VD HD VSG tEXP tEXP SUBCK NOTES 1. SECOND SUBCK PULSE IS ADDED IN THE LAST SUBCK LINE. 2. LOCATION OF 2ND PULSE IS FULLY PROGRAMMABLE USING THE SUBCK2 TOGGLE POSITION REGISTER. Figure 27. High Precision Shutter Mode -26- REV. 0 AD9995 If the exposure is generated using the TRIGGER register and the EXPOSURE register is set to zero, the behavior of the SUBCK will not be any different than the normal shutter or high precision shutter operations, in which the TRIGGER register is not used. SUBCK Suppression CCD frame readout mode will generally require two additional fields of SUBCK suppression (READOUT = 2). A 3-field, 6-phase CCD will require three additional fields of SUBCK suppression after the readout begins (READOUT = 3). If the SUBCK output is required to start back up during the last field of readout, simply program the READOUT register to one less than the total number of CCD readout fields. Like the exposure operation, the readout operation must be triggered by using the TRIGGER register. Using the TRIGGER Register Normally, the SUBCKs will begin to pulse on the line following the sensor gate line (VSG). With some CCDs, the SUBCK pulse needs to be suppressed for one or more lines following the VSG line. The SUBCKSUPPRESS register allows for suppression of the SUBCK pulses for additional lines following the VSG line. Readout after Exposure After the exposure, the readout of the CCD data occurs, beginning with the sensor gate (VSG) operation. By default, the AD9995 is generating the VSG pulses in every field. In the case where only a single exposure and single readout frame are needed, such as the CCD's preview mode, the VSG and SUBCK pulses can be operating in every field. However in many cases, during readout the SUBCK output needs to be further suppressed until the readout is completed. The READOUT register specifies the number of additional fields after the exposure to continue the suppression of SUBCK. READOUT can be programmed for zero to seven additional fields, and should be preprogrammed at startup, not at the same time as the exposure write. A typical interlaced TRIGGER EXPOSURE As described previously, by default the AD9995 will output the SUBCK and VSG signals on every field. This works well for continuous single field exposure and readout operations, such as the CCD's live preview mode. However, if the CCD requires a longer exposure time, or if multiple readout fields are needed, the TRIGGER register is needed to initiate specific exposure and readout sequences. Typically, the exposure and readout bits in the TRIGGER register are used together. This will initiate a complete exposureplus-readout operation. Once the exposure has been completed, the readout will automatically occur. The values in the EXPOSURE and READOUT registers will determine the length of each operation. VD VSG tEXP SUBCK NOTES 1. SUBCK MAY BE SUPPRESSED FOR MULTIPLE FIELDS BY PROGRAMMING THE EXPOSURE REGISTER GREATER THAN ZERO. 2. ABOVE EXAMPLE USES EXPOSURE = 1. 3. TRIGGER REGISTER MUST ALSO BE USED TO START THE LOW SPEED EXPOSURE. 4. VD/HD OUTPUTS MAY ALSO BE SUPPRESSED USING THE VDHDOFF REGISTER = 1. Figure 28. Low Speed Shutter Mode Using EXPOSURE Register Table XI. Shutter Mode Register Parameters Register TRIGGER READOUT EXPOSURE VDHDOFF SUBCKPOL* SUBCK1TOG* SUBCK2TOG* SUBCKNUM* SUBCKSUPPRESS* Length 5b 3b 12b 1b 1b 24b 24b 12b 12b Range On/Off for Five Signals 0-7 # of Fields 0-4095 # of Fields On/Off High/Low 0-4095 Pixel Locations 0-4095 Pixel Locations 1-4095 # of Pulses 0-4095 # of Pulses Description Trigger for VSUB [0], MSHUT [1], STROBE [2], Exposure [3], and Readout Start [4] Number of Fields to Suppress SUBCK after Exposure Number of Fields to Suppress to SUBCK and VSG during Exposure Time (Low Speed Shutter) Disable VD/HD Output during Exposure (1 = On, 0 = Off) SUBCK Start Polarity for SUBCK1 and SUBCK2 Toggle Positions for First SUBCK Pulse (Normal Shutter) Toggle Positions for Second SUBCK Pulse in Last Line (High Precision) Total Number of SUBCKs per Field at One Pulse per Line Number of Lines to Further Suppress SUBCK after the VSG Line *Register is not VD updated, but is updated at the start of line after sensor gate line. REV. 0 -27- AD9995 It is possible to independently trigger the readout operation without triggering the exposure operation. This will cause the readout to occur at the next VD, and the SUBCK output will be suppressed according to the value of the READOUT register. The TRIGGER register is also used to control the STROBE, MSHUT, and VSUB signal transitions. Each of these signals are individually controlled, although they will be dependent on the triggering of the exposure and readout operation. See Figure 32 for a complete example of triggering the exposure and readout operations. VSUB Control the field. VSUB will remain active until the end of the image readout. In Mode 1, the VSUB is not activated until the start of the readout. An additional function called VSUB KEEP-ON is also available. When this bit is set high, the VSUB output will remain on (active) even after the readout has finished. To disable the VSUB at a later time, set this bit back to low. MSHUT and STROBE Control The CCD readout bias (VSUB) can be programmed to accommodate different CCDs. Figure 29 shows two different modes that are available. In Mode 0, VSUB goes active during the field of the last SUBCK when the exposure begins. The On position (rising edge in Figure 29) is programmable to any line within TRIGGER VSUB MSHUT and STROBE operation is shown in Figures 30, 31, and 32. Table XII shows the register parameters for controlling the MSHUT and STROBE outputs. The MSHUT output is switched on with the MSHUTON registers, and will remain on until the location specified in the MSHUTOFF registers. The location of MSHUTOFF is fully programmable to anywhere within the exposure period, using the FD (field), LN (line), and PX (pixel) registers. The STROBE pulse is defined by the on and VD VSG1 tEXP SUBCK 2 VSUB 1 MODE 0 MODE 1 2 READOUT 4 3 VSUB OPERATION: 1. ACTIVE POLARITY IS POLARITY (ABOVE EXAMPLE IS VSUB ACTIVE HIGH). 2. ON POSITION IS PROGRAMMABLE. MODE 0 TURNS ON AT THE START OF EXPOSURE, MODE 1 TURNS ON AT THE START OF READOUT. 3. OFF POSITION OCCURS AT END OF READOUT. 4. OPTIONAL VSUB KEEP-ON MODE WILL LEAVE THE VSUB ACTIVE AT THE END OF READOUT. Figure 29. VSUB Programmability TRIGGER EXPOSURE AND MSHUT VD VSG tEXP SUBCK MSHUT 1 2 3 MSHUT PROGRAMMABLE SETTINGS: 1. ACTIVE POLARITY. 2. ON POSITION IS VD UPDATED AND MAY BE SWITCHED ON AT ANY TIME. 3. OFF POSITION CAN BE PROGRAMMED ANYWHERE FROM THE FIELD OF LAST SUBCK UNTIL THE FIELD BEFORE READOUT. Figure 30. MSHUT Output Programmability -28- REV. 0 AD9995 off positions. STROBON_FD is the field in which the STROBE is turned on, measured from the field containing the last SUBCK before exposure begins. The STROBON_ LN PX register gives the line and pixel positions with respect to STROBON_FD. The STROBE off position is programmable to any field, line, and pixel location with respect to the field of the last SUBCK. TRIGGER Register Limitations The same limitation applies to the triggering of the MSHUT signal. There must be at least one idle field after the completion of the MSHUT OFF operation before another MSHUT OFF operation may be programmed. The VSUB trigger requires two idle fields between exposure/ readout operations in order to ensure proper VSUB on/off triggering. If the VSUB signal is not required to be turned on and off in between each successive exposure/readout operation, this limitation can be ignored. The VSUB Keep-On mode is useful when successive exposure/readout operations are required. While the TRIGGER register can be used to perform a complete exposure and readout operation, there are limitations on its use. Once an exposure-plus-readout operation has been triggered, another exposure/readout operation cannot be triggered right away. There must be at least one idle field (VD intervals) before the next exposure/readout can be triggered. TRIGGER EXPOSURE AND STROBE VD VSG tEXP SUBCK STROBE 1 2 3 STROBE PROGRAMMABLE SETTINGS: 1. ACTIVE POLARITY. 2. ON POSITION IS PROGRAMMABLE IN ANY FIELD DURING THE EXPOSURE TIME (WITH RESPECT TO THE FIELD CONTAINING THE LAST SUBCK). 3. OFF POSITION IS PROGRAMMABLE IN ANY FIELD DURING THE EXPOSURE TIME. Figure 31. STROBE Output Programmability Table XII. VSUB, MSHUT, and STROBE Register Parameters Register VSUBMODE[0] VSUBMODE[1] VSUBON[11:0] VSUBON[12] MSHUTPOL[0] MSHUTPOL[1] MSHUTON MSHUTOFF_FD MSHUTOFF_LNPX STROBPOL STROBON_FD STROBON_LNPX STROBOFF_FD STROBOFF_LNPX Length 1b 1b 12b 1b 1b 1b 24b 12b 24b 1b 12b 24b 12b 24b Range High/Low High/Low 0-4095 Line Location High/Low High/Low On/Off 0-4095 Line/Pix Location 0-4095 Field Location 0-4095 Line/Pix Location High/Low 0-4095 Field Location 0-4095 Line/Pix Location 0-4095 Field Location 0-4095 Line/Pix Location Description VSUB Mode (0 = Mode 0, 1 = Mode 1) (See Figure 29). VSUB Keep-On Mode. VSUB will stay active after readout when set high. VSUB On Position. Active starting in any line of field. VSUB Active Polarity. MSHUT Active Polarity. MSHUT Manual Enable (1 = Active or Open). MSHUT On Position Line [11:0] and Pixel [23:12] Location. Field Location to Switch Off MSHUT (Inactive or Closed). Line/Pixel Position to Switch Off MSHUT (Inactive or Closed). STROBE Active Polarity. STROBE ON Field Location, with Respect to Last SUBCK Field. STROBE ON Line/Pixel Position. STROBE OFF Field Location, with Respect to Last SUBCK Field. STROBE OFF Line/Pixel Position. REV. 0 -29- AD9995 EXPOSURE AND READOUT EXAMPLE SERIAL WRITES 1 2 VD 6 7 8 9 10 STILL IMAGE READOUT VSG SUBCK 4 STROBE tEXP 10 5 MSHUT 10 MECHANICAL SHUTTER OPEN CLOSED OPEN 3 VSUB MODE 0 MODE 1 10 CCD OUT DRAFT IMAGE DRAFT IMAGE STILL IMAGE 1ST FIELD STILL IMAGE 2ND FIELD STILL IMAGE 3RD FIELD DRAFT IMAGE Figure 32. Example of Exposure and Still Image Readout Using Shutter Signals and Mode Register 1. Write to the READOUT register (Addr. 0x61) to specify the number of fields to further suppress SUBCK while the CCD data is read out. In this example, READOUT = 3. Write to the EXPOSURE register (Addr. 0x62) to specify the number of fields to suppress SUBCK and VSG outputs during exposure. In this example, EXPOSURE = 1. Write to the TRIGGER register (Addr. 0x60) to enable the STROBE, MSHUT, and VSUB signals, and to start the exposure/readout operation. To trigger all of these events (as in Figure 32), set the register TRIGGER = 31. Readout will automatically occur after the exposure period is finished. Write to the MODE register (Addr. 0x1B) to configure the next five fields. The first two fields during exposure are the same as the current draft mode fields, and the following three fields are the still frame readout fields. The registers for the Draft mode field and the three readout fields have already been programmed. 2. VD/HD falling edge will update the serial writes from 1. 3. If VSUB mode = 0 (Addr. 0x67), VSUB output turns on at the line specified in the VSUBON register (Addr. 0x68). 4. STROBE output turns on and off at the location specified in the STROBEON and OFF registers (Addr. 0x6E to Addr. 0x71). 5. MSHUT output turns off at the location specified in the MSHUTOFF registers (Addr. 0x6B and 0x6C). 6. The next VD falling edge will automatically start the first readout field. 7. The next VD falling edge will automatically start the second readout field. 8. The next VD falling edge will automatically start the third readout field. 9. Write to the MODE register to reconfigure the single Draft mode field timing. Write to the MSHUTON register (Addr. 0x6A) to open the mechanical shutter. 10. VD/HD falling edge will update the serial write from 9. VSG outputs return to Draft mode timing. SUBCK output resumes operation. MSHUT output returns to the on position (active or open). VSUB output returns to the off position (inactive). -30- REV. 0 AD9995 1.0F 1.0F REFB DC RESTORE 1.5V SHP 0.1F 1.0V REFT 2.0V AD9995 INTERNAL VREF SHD 2V FULL SCALE 12-BIT ADC OUTPUT DATA LATCH DOUT PHASE 6dB-42dB VGA CCDIN CDS 12 DOUT VGA GAIN REGISTER DAC OPTICAL BLACK CLAMP CLPOB PBLK DIGITAL FILTER 8 DOUT SHP SHD PHASE CLPOB PBLK CLAMP LEVEL REGISTER PRECISION TIMING GENERATION V-H TIMING GENERATION Figure 33. Analog Front End Functional Block Diagram ANALOG FRONT END DESCRIPTION AND OPERATION The AD9995 signal processing chain is shown in Figure 33. Each processing step is essential in achieving a high quality image from the raw CCD pixel data. DC Restore with the ADC full-scale range of 2 V. When compared to 1 V full-scale systems, the equivalent gain range is 0 dB to 36 dB. The VGA gain curve follows a linear-in-dB characteristic. The exact VGA gain can be calculated for any gain register value by using the equation Gain (dB) = (0.0351 x Code) + 6 dB where the code range is 0 to 1023. 42 To reduce the large dc offset of the CCD output signal, a dc restore circuit is used with an external 0.1 F series coupling capacitor. This restores the dc level of the CCD signal to approximately 1.5 V, to be compatible with the 3 V supply voltage of the AD9995. Correlated Double Sampler The CDS circuit samples each CCD pixel twice to extract the video information and reject low frequency noise. The timing shown in Figure 7 illustrates how the two internally generated CDS clocks, SHP and SHD, are used to sample the reference level and level of the CCD signal, respectively. The placement of the SHP and SHD sampling edges is determined by the setting of the SAMPCONTROL register located at Addr. 0x63. Placement of these two clock signals is critical in achieving the best performance from the CCD. Variable Gain Amplifier 36 VGA GAIN (dB) 30 24 18 12 The VGA stage provides a gain range of 6 dB to 42 dB, programmable with 10-bit resolution through the serial digital interface. The minimum gain of 6 dB is needed to match a 1 V input signal 6 0 127 255 383 511 639 767 VGA GAIN REGISTER CODE 895 1023 Figure 34. VGA Gain Curve REV. 0 -31- AD9995 A/D Converter The AD9995 uses a high performance ADC architecture optimized for high speed and low power. Differential nonlinearity (DNL) performance is typically better than 0.5 LSB. The ADC uses a 2 V input range. See TPC 2 and TPC 3 for typical linearity and noise performance plots for the AD9995. Optical Black Clamp The optical black clamp loop is used to remove residual offsets in the signal chain and to track low frequency variations in the CCD's black level. During the optical black (shielded) pixel interval on each line, the ADC output is compared with a fixed black level reference, selected by the user in the Clamp Level register. The value can be programmed between 0 LSB and 255 LSB in 256 steps. The resulting error signal is filtered to reduce noise, and the correction value is applied to the ADC input through a D/A converter. Normally, the optical black clamp loop is turned on once per horizontal line, but this loop can be updated more slowly to suit a particular application. If external digital clamping is used during the postprocessing, the AD9995 optical black clamping may be disabled using Bit D2 in the OPRMODE register. When the loop is disabled, the Clamp Level register may still be used to provide programmable offset adjustment. The CLPOB pulse should be placed during the CCD's optical black pixels. It is recommended that the CLPOB pulse duration be at least 20 pixels wide to minimize clamp noise. Shorter pulsewidths may be used, but clamp noise may increase, and the ability to track low frequency variations in the black level will be reduced. See the Horizontal Clamping and Blanking section and the Horizontal Timing Sequence Example section for timing examples. Digital Data Outputs The AD9995 digital output data is latched using the DOUT PHASE register value, as shown in Figure 33. Output data timing is shown in Figure 8a. It is also possible to leave the output latches transparent so that the data outputs are valid immediately from the A/D converter. Programming the AFE CONTROL register bit D4 to 1 will set the output latches transparent. The data outputs can also be disabled (three-stated) by setting the AFE CONTROL register Bit D3 to 1. The data output coding is normally straight binary, but the coding my be changed to gray coding by setting the AFE CONTROL register Bit D5 to 1. -32- REV. 0 AD9995 POWER-UP AND SYNCHRONIZATION Recommended Power-Up Sequence for Master Mode When the AD9995 is powered up, the following sequence is recommended (refer to Figure 35 for each step). Note that a SYNC signal is required for Master mode operation. If an external SYNC pulse is not available, it is also possible generate an internal SYNC pulse by writing to the SYNCPOL register, as described in the next section. 1. Turn on power supplies for AD9995. 2. Apply the master clock input CLI. 3. Reset the internal AD9995 registers by writing a 1 to the SW_RESET register (Addr. 0x10 in Bank 1). 4. By default, the AD9995 is in Standby3 mode. To place the part into normal power operation, write 0x004 to the AFE OPRMODE register (Addr. 0x00 in Bank 1). 5. Write a 1 to the BANKSELECT register (Addr. 0x7F). This will select Register Bank 2. 6. Load Bank 2 registers with the required VPAT group, V-sequence, and field timing information. 7. Write a 0 to the BANKSELECT register to select Bank 1. 8. By default, the internal timing core is held in a reset state with TGCORE_RSTB register = 0. Write a 1 to the TGCORE_RSTB register (Addr. 0x15 in Bank 1) to start the internal timing core operation. 9. Load the required registers to configure the high speed timing, horizontal timing, and shutter timing information. 10. Configure the AD9995 for Master mode timing by writing a 1 to the MASTER register (Addr. 0x20 in Bank 1). 11. Write a 1 to the OUT_CONTROL register (Addr. 0x11 in Bank 1). This will allow the outputs to become active after the next SYNC rising edge. 12. Generate a SYNC event: If SYNC is high at power-up, bring the SYNC input low for a minimum of 100 ns. Then bring SYNC back high. This will cause the internal counters to reset and will start VD/HD operation. The first VD/HD edge allows most Bank 1 register updates to occur, including OUT_CONTROL to enable all outputs. Table XIII. Power-Up Register Write Sequence Address 0x10 0x00 0x7F 0x00-0xFF 0x7F 0x15 0x30-71 0x20 0x11 0x13 Data 0x01 0x04 0x01 0x00 0x01 0x01 0x01 0x01 Description Reset All Registers to Default Values Power Up the AFE and CLO Oscillator Select Register Bank 2 VPAT, V-Sequence, and Field Timing Select Register Bank 1 Reset Internal Timing Core Horizontal and Shutter Timing Configure for Master Mode Enable All Outputs after SYNC SYNCPOL (for Software SYNC Only) Generating Software SYNC without External SYNC Signal If an external SYNC pulse is not available, it is possible to generate an internal SYNC in the AD9995 by writing to the SYNCPOL register (Addr. 0x13). If the software SYNC option is used, the SYNC input (Pin 46) should be tied to ground (VSS). After power-up, follow the same procedure as before for Steps 1 to 11. Then, for Step 12, instead of using the external SYNC pulse, write a 1 to the SYNCPOL register. This will generate the SYNC internally, and timing operation will begin. VDD (INPUT) 1 CLI (INPUT) 2 tPWR SERIAL WRITES 3 4 5 6 7 8 9 10 11 12 SYNC (INPUT) tSYNC 1V VD (OUTPUT) 1ST FIELD 1H HD (OUTPUT) H2/H4 DIGITAL OUTPUTS H1/H3, RG, DCLK CLOCKS ACTIVE WHEN OUT CONTROL REGISTER IS UPDATED AT VD/HD EDGE Figure 35. Recommended Power-Up Sequence and Synchronization, Master Mode REV. 0 -33- AD9995 SYNC during Master Mode Operation STANDBY MODE OPERATION The SYNC input may be used at any time during operation to resync the AD9995 counters with external timing, as shown in Figure 36. The operation of the digital outputs may be suspended during the SYNC operation by setting the SYNCSUSPEND register (Addr. 0x14) to 1. Power-Up and Synchronization in Slave Mode The AD9995 contains three different standby modes to optimize the overall power dissipation in a particular application. Bits [1:0] of the OPRMODE register control the power-down state of the device: OPRMODE [1:0] = 00 = Normal Operation (Full Power) OPRMODE[1:0] = 01 = Standby 1 Mode OPRMODE[1:0] = 10 = Standby 2 Mode OPRMODE[1:0] = 11 = Standby 3 Mode (Lowest Overall Power) Table XIV summarizes the operation of each power-down mode. Note that the OUT_CONTROL register takes priority over the Standby 1 and Standby 2 modes in determining the digital output states, but Standby 3 mode takes priority over OUT_CONTROL. Standby 3 has the lowest power consumption, and even shuts down the crystal oscillator circuit between CLI and CLO. Therefore, if CLI and CLO are being used with a crystal to generate the master clock, this circuit will be powered down and there will be no clock signal. When returning from Standby 3 mode to normal operation, the timing core must be reset at least 500 s after the OPRMODE register is written to. This will allow sufficient time for the crystal circuit to settle. The power-up procedure for Slave mode operation is the same as the procedure described for Master mode operation, with two exceptions: * Eliminate Step 9. Do not write the part into Master mode. * No SYNC pulse is required in Slave mode. Substitute Step 12 with starting the external VD and HD signals. This will synchronize the part, allow Bank 1 register updates, and start the timing operation. When the AD9995 is used in Slave mode, the VD and HD inputs are used to synchronize the internal counters. Following a falling edge of VD, there will be a latency of 17 master clock cycles (CLI) after the falling edge of HD until the internal H-counter will be reset. The reset operation is shown in Figure 37. SYNC VD SUSPEND HD H124, RG, V1-V4, VSG, SUBCK NOTES 1. SYNC RISING EDGE RESETS VD/HD AND COUNTERS TO ZERO. 2. SYNC POLARITY IS PROGRAMMABLE USING SYNCPOL REGISTER (ADDR 0x13). 3. DURING SYNC LOW, ALL INTERNAL COUNTERS ARE RESET AND VD/HD CAN BE SUSPENDED USING THE SYNCSUSPEND REGISTER (ADDR 0x14). 4. IF SYNCSUSPEND = 1, VERTICAL CLOCKS, H1-H2, AND RG ARE HELD AT THEIR DEFAULT POLARITIES. 5. IF SYNCSUSPEND = 0, ALL CLOCK OUTPUTS CONTINUE TO OPERATE NORMALLY UNTIL SYNC RESET EDGE. Figure 36. SYNC Timing to Synchronize AD9995 with External Timing VD HD H-COUNTER RESET CLI H-COUNTER (PIXEL COUNTER) X X X X X X X X X X X X X X X X X X X 0 1 2 3 4 5 6 7 8 9 NOTES INTERNAL H-COUNTER IS RESET 17 CLI CYCLES AFTER THE HD FALLING EDGE (WHEN USING VDHDPOL = 0). TYPICAL TIMING RELATIONSHIP: CLI RISING EDGE IS COINCIDENT WITH HD FALLING EDGE. Figure 37. External VD/HD and Internal H-Counter Synchronization, Slave Mode -34- REV. 0 AD9995 Table XIV. Standby Mode Operation I/O Block AFE Timing Core CLO Oscillator CLO V1 V2 V3 V4 V5 V6 VSG1 VSG2 VSG3 VSG4 VSG5 SUBCK VSUB MSHUT STROBE H1 H2 H3 H4 RG VD HD DCLK DOUT Standby 3 (Default) OFF OFF OFF HI LO LO LO LO LO LO LO LO LO LO LO LO LO LO LO Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z LO LO LO LO 1, 2 OUT_CONT = LO2, 3 No Change No Change No Change Running LO LO LO LO HI HI HI HI HI HI HI HI LO LO LO LO HI LO HI LO VDHDPOL Value VDHDPOL Value LO LO Standby 23, 4 OFF OFF ON Running LO LO LO LO HI HI HI HI HI HI HI HI LO LO LO LO (4.3 mA) HI (4.3 mA) LO (4.3 mA) HI (4.3 mA) LO (4.3 mA) VDHDPOL Value VDHDPOL Value LO LO Standby 13, 4 Only REFT, REFB ON ON ON Running LO LO LO LO HI HI HI HI HI HI HI HI LO LO LO LO (4.3 mA) HI (4.3 mA) LO (4.3 mA) HI (4.3 mA) LO (4.3 mA) Running Running Running LO NOTES 1 To exit Standby 3, first write 00 to OPRMODE[1:0], then reset the Timing Core after ~500 s to guarantee proper settling of the oscillator. 2 Standby 3 mode takes priority over OUT_CONTROL for determining the output polarities. 3 These polarities assume OUT_CONT = HI because OUT_CONTROL = LO takes priority over Standby 1 and 2. 4 Standby 1 and 2 will set H and RG drive strength to minimum value (4.3 mA). REV. 0 -35- AD9995 3V ANALOG SUPPLY 0.1F TO STROBE CIRCUIT TO MECHANICAL SHUTTER CIRCUIT 3 3 SERIAL INTERFACE TO ASIC OR DSP EXTERNAL SYNC FROM ASIC/DSP LINE/FIELD/DCLK TO ASIC/DSP 51 DCLK 50 HD 45 STROBE 44 MSHUT 49 DVDD 48 DVSS 47 VD 46 SYNC 56 D4 55 54 53 52 43 SCK D3 D2 D1 D0 D5 D6 D7 D8 D9 12 D10 D11 DRVDD DRVSS 0.1F 1 2 3 4 5 6 7 8 9 PIN 1 IDENTIFIER 42 41 40 39 38 SDI SL REFB REFT AVSS CCDIN AVDD CLI CLO TCVDD TCVSS RGVDD RG RGVSS 0.1F 0.1F 1F 1F 0.1F OUTPUT FROM CCD MASTER CLOCK INPUT 3V ANALOG + SUPPLY 4.7F 3V RG SUPPLY AD9995 TOP VIEW 37 36 35 34 33 32 31 30 29 DATA OUTPUTS 3V DRIVER + SUPPLY 4.7F VSUB 10 SUBCK 11 V1 12 V2 13 V3 14 0.1F VSUB TO CCD + 4.7F VSG3 20 V6 17 VSG1 18 VSG2 19 VSG4 21 V4 15 V5 16 H1 23 HVSS 25 VSG5 22 H2 24 HVDD 26 H3 27 H4 28 RG, H1-H4 TO CCD 5 12 V1-V4, VSG1-VSG4, SUBCK TO V-DRIVER 0.1F + 4.7F 3V H1-H4 SUPPLY Figure 38. Typical Circuit Configuration CIRCUIT LAYOUT INFORMATION The AD9995 typical circuit connection is shown in Figure 38. The PCB layout is critical in achieving good image quality from the AD999x products. All of the supply pins, particularly the AVDD1, TCVDD, RGVDD, and HVDD supplies, must be decoupled to ground with good quality, high frequency chip capacitors. The decoupling capacitors should be located as close as possible to the supply pins and should have a very low impedance path to a continuous ground plane. There should also be a 4.7 F or larger value bypass capacitor for each main supply--AVDD, RGVDD, HVDD, and DRVDD--although this is not necessary for each individual pin. In most applications, it is easier to share the supply for RGVDD and HVDD, which may be done as long as the individual supply pins are separately bypassed. A separate 3 V supply may also be used for DRVDD, but this supply pin should still be decoupled to the same ground plane as the rest of the chip. A separate ground for DRVSS is not recommended. It is recommended that the exposed paddle on the bottom of the package be soldered to a large pad, with multiple vias connecting the pad to the ground plane. The analog bypass pins (REFT, REFB) should also be carefully decoupled to ground as close as possible to their respective pins. The analog input (CCDIN) capacitor should also be located close to the pin. The H1-H4 and RG traces should be designed to have low inductance to avoid excessive distortion of the signals. Heavier traces are recommended because of the large transient current demand on H1-H4 by the CCD. If possible, locating the AD9995 physically closer to the CCD will reduce the inductance on these lines. As always, the routing path should be as direct as possible from the AD9995 to the CCD. The AD9995 also contains an on-chip oscillator for driving an external crystal. Figure 39 shows an example application using a typical 24 MHz crystal. For the exact values of the external resistors and capacitors, it is best to consult with the crystal manufacturer's data sheet. AD9995 35 CLI 1M 0 1 D 34 CLO 500M 20pF 20pF 24MHz XTAL Figure 39. Crystal Driver Application -36- REV. 0 AD9995 SERIAL INTERFACE TIMING All of the internal registers of the AD9995 are accessed through a 3-wire serial interface. Each register consists of an 8-bit address and a 24-bit data-word. Both the 8-bit address and 24-bit dataword are written starting with the LSB. To write to each register, a 32-bit operation is required, as shown in Figure 40a. Although many registers are fewer than 24 bits wide, all 24 bits must be written for each register. For example, if the register is only 10 bits wide, the upper 14 bits are don't cares and may be filled with 0s during the serial write operation. If fewer than 24 bits are written, the register will not be updated with new data. 8-BIT ADDRESS SDATA A0 A1 A2 A3 A4 A5 A6 A7 D0 D1 Figure 40b shows a more efficient way to write to the registers, using the AD9995's address auto-increment capability. Using this method, the lowest desired address is written first, followed by multiple 24-bit data-words. Each new 24-bit data-word will automatically be written to the next highest register address. By eliminating the need to write each 8-bit address, faster register loading is achieved. Continuous write operations may be used starting with any register location, and may be used to write to as few as two registers, or as many as the entire register space. 24-BIT DATA D2 D3 ... ... ... D21 D22 D23 tDS SCK 1 2 3 4 tDH 5 6 7 8 9 10 11 12 30 31 32 tLS SL tLH NOTES 1. SDATA BITS ARE LATCHED ON SCK RISING EDGES. SCK MAY IDLE HIGH OR LOW IN BETWEEN WRITE OPERATIONS. 2. ALL 32 BITS MUST BE WRITTEN: 8 BITS FOR ADDRESS AND 24 BITS FOR DATA. 3. IF THE REGISTER LENGTH IS <24 BITS, "DON'T CARE" BITS MUST BE USED TO COMPLETE THE 24-BIT DATA LENGTH. 4. NEW DATA VALUES ARE UPDATED IN THE SPECIFIED REGISTER LOCATION AT DIFFERENT TIMES, DEPENDING ON THE PARTICULAR REGISTER WRITTEN TO. SEE THE REGISTER UPDATES SECTION FOR MORE INFORMATION. Figure 40a. Serial Write Operation DATA FOR STARTING REGISTER ADDRESS SDATA A0 A1 A2 A3 A4 A5 A6 A7 D0 D1 ... DATA FOR NEXT REGISTER ADDRESS D23 D0 D1 D22 ... D22 D23 D0 D1 D2 ... ... ... SCK 1 2 3 4 5 6 7 8 9 10 ... ... 31 32 33 34 ... ... 55 56 57 58 59 SL NOTES 1. MULTIPLE SEQUENTIAL REGISTERS MAY BE LOADED CONTINUOUSLY. 2. THE FIRST (LOWEST ADDRESS) REGISTER ADDRESS IS WRITTEN, FOLLOWED BY MULTIPLE 24-BIT DATA-WORDS. 3. THE ADDRESS WILL AUTOMATICALLY INCREMENT WITH EACH 24-BIT DATA-WORD (ALL 24 BITS MUST BE WRITTEN). 4. SL IS HELD LOW UNTIL THE LAST DESIRED REGISTER HAS BEEN LOADED. Figure 40b. Continuous Serial Write Operation REV. 0 -37- AD9995 Register Address Banks 1 and 2 The AD9995 address space is divided into two different register banks, referred to as Register Bank 1 and Register Bank 2. Figure 41 illustrates how the two banks are divided. Register Bank 1 contains the registers for the AFE, miscellaneous functions, VD/HD parameters, timing core, CLPOB masking, VSG patterns, and shutter functions. Register Bank 2 contains all of the information for the V-pattern groups, V-sequences, and field information. When writing to the AD9995, Address 0x7F is used to specify which address bank is being written to. To write to Bank 1, the LSB of Address 0x7F should be set to 0; to write to Bank 2, the LSB of Address 0x7F should be set to 1. Note that Register Bank 1 contains many unused addresses. Any undefined addresses between 0x00 and 0x7F are considered don't cares, and it is acceptable if these addresses are filled in with all 0s during a continuous register write operation. However, the undefined addresses above 0x7F must not be written to, or the AD9995 may not operate properly. REGISTER BANK 2 ADDR 0x00 REGISTER BANK 1 ADDR 0x00 ADDR 0x10 MISCELLANEOUS REGISTERS ADDR 0x20 ADDR 0x30 ADDR 0x40 ADDR 0x50 VSG PATTERN REGISTERS ADDR 0x60 SHUTTER REGISTERS ADDR 0xCF ADDR 0xD0 VD/HD REGISTERS TIMING CORE REGISTERS CLPOB MASK REGISTERS ADDR 0x7E ADDR 0x7F ADDR 0x80 AFE REGISTERS VPAT0-VPAT9 REGISTERS SWITCH TO REGISTER BANK 1 VSEQ0-VSEQ9 REGISTERS ADDR 0x7F ADDR 0x8F SWITCH TO REGISTER BANK 2 INVALID--DO NOT ACCESS FIELD 0-FIELD 5 REGISTERS ADDR 0xFF ADDR 0xFF WRITE TO ADDRESS 0x7F TO SWITCH REGISTER BANKS Figure 41. Layout of Internal Register Banks 1 and 2 -38- REV. 0 AD9995 Updating New Register Values The AD9995's internal registers are updated at different times, depending on the particular register. Table XV summarizes the four different types of register updates: 1. SCK Updated: Some of the registers in Bank 1 are updated immediately, as soon as the 24th data bit (D23) is written. These registers are used for functions that do not require gating with the next VD boundary, such as power-up and reset functions. These registers are lightly shaded in gray in the Bank 1 register list. The Bank Select register (Addr. 0x7F in Bank 1 and 2) is also SCK updated. 2. VD Updated: Most of the registers in Bank 1, as well as the Field registers in Bank 2, are updated at the next VD falling edge. By updating these values at the next VD edge, the current field will not be corrupted and the new register values will be applied to the next field. The Bank 1 register updates may be further delayed past the VD falling edge by using the UPDATE register (Addr. 0x19). This will delay the VD updated register updates to any HD line in the field. Note that the Bank 2 registers are not affected by the UPDATE register. 3. SG-Line Updated: A few of the registers in Bank 1 are updated at the end of the SG active line, at the HD falling edge. These are the registers to control the SUBCK signal so that the SUBCK output will not be updated until after the SG line has been completed. These registers are darkly shaded in gray in the Bank 1 register list. 4. SCP Updated: In Bank 2, all of the V-pattern group and V-sequence registers (Addr. 0x00 through 0xCF, excluding 0x7F) are updated at the next SCP, where they will be used. For example, in Figure 42, this field has selected Region 1 to use V-Sequence 3 for the vertical outputs. This means that a write to any of the V-Sequence 3 registers, or any of the V-pattern group registers that are referenced by V-Sequence 3 will be updated at SCP1. If multiple writes are done to the same register, the last one done before SCP1 will be the one that is updated. Likewise, register writes to any V-Sequence 5 registers will be updated at SCP2, and register writes to any V-Sequence 8 registers will be updated at SCP3. Table XV. Register Update Locations Update Type SCK Updated VD Updated SG Line Updated SCP Updated Register Bank Bank 1 Only Bank 1 and Bank 2 Bank 1 Only Bank 2 Only Description Register is immediately updated when the 24th data bit (D23) is clocked in. Register is updated at the VD falling edge. VD updated registers in Bank 1 may be delayed further by using the UPDATE register at Address 0x19 in Bank 1. Bank 2 updates will not be affected by the UPDATE register. Register is updated at the HD falling edge at the end of the SG-active line. Register is updated at the next SCP when the register will be used. SCK UPDATED SERIAL WRITE VD UPDATED SG UPDATED SCP UPDATED VD HD SGLINE VSG V1-V6 USE VSEQ2 REGION 0 SCP 0 USE VSEQ3 REGION 1 SCP 1 USE VSEQ5 REGION 2 SCP 2 USE VSEQ8 REGION 3 SCP 3 SCP 0 Figure 42. Register Update Locations (See Table XV for Definitions) REV. 0 -39- AD9995 COMPLETE LISTING FOR REGISTER BANK 1 All registers are VD updated, except where noted: All address and default values are in hexadecimal. = SCK Updated = SG-Line Updated Table XVI. AFE Register Map Data Bit Default Address Content Value Register Name 00 01 02 03 [11:0] [9:0] [7:0] [11:0] 7 0 80 4 OPRMODE VGAGAIN CLAMPLEVEL CTLMODE Register Description AFE Operation Modes (see Table XXIV for detail). VGA Gain. Optical Black Clamp Level. AFE Control Modes (see Table XXV for detail). Table XVII. Miscellaneous Register Map Data Bit Default Address Content Value Register Name 10 11 12 13 14 15 16 17 18 19 1A 1B 1C [0] [11:0] [0] [23:0] [1:0] 0 0 0 0 0 TEST USE UPDATE PREVENTUPDATE MODE FIELDVAL [0] [0] [0] [0] [0] [0] [0] 0 0 1 0 0 0 1 SW_RST OUTCONTROL TEST USE SYNCPOL SYNCSUSPEND TGCORE_RSTB OSC_PWRDOWN Register Description Software Reset. 1 = Reset all registers to default, then self-clear back to 0. Output Control. 0 = Make all outputs dc inactive. Internal Use Only. Must be set to 1. SYNC Active Polarity (0 = Active Low). Suspend Clocks during SYNC Active (1 = Suspend). Timing Core Reset Bar. 0 = Reset TG Core, 1 = Resume Operation. CLO Oscillator Power-Down (0 = Oscillator is powered-down). Unused. Internal Use Only. Must be set to 0. Serial Update. Line (HD) in the field to update VD updated registers. Prevents the Update of the VD Updated Registers. 1 = Prevent update. Mode Register. Field Value Sync. 0 = Next Field 0, 1 = Next Field 1, 2/3 = Next Field 2. Table XVIII. VD/HD Register Map Data Bit Default Address Content Value Register Name 20 21 22 [0] [0] [17:0] 0 0 0 MASTER VDHDPOL VDHDRISE Register Description VD/HD Master or Slave Timing (0 = Slave mode). VD/HD Active Polarity. 0 = Low, 1 = High. Rising Edge Location for VD [17:12] and HD [11:0]. -40- REV. 0 AD9995 Table XIX. Timing Core Register Map Data Bit Default Address Content Value Register Name 30 31 32 33 34 [0] [12:0] [12:0] [12:0] [1:0] 0 01001 01001 00801 0 CLIDIVIDE H1CONTROL H3CONTROL RGCONTROL HBLKRETIME Register Description Divide CLI Input Clock by 2. 1 = Divide by 2. H1 Signal Control: Polarity [0](0 = Inversion, 1 = No Inversion). H1 Positive Edge Location [6:1]. H1 Negative Edge Location [12:7]. H3 Signal Control: Polarity [0](0 = Inversion, 1 = No Inversion). H3 Positive Edge Location [6:1]. H3 Negative Edge Location [12:7]. RG Signal Control: Polarity [0](0 = Inversion, 1 = No Inversion). RG Positive Edge Location [6:1]. RG Negative Edge Location [12:7]. Retime HBLK to Internal H1/H3 Clocks. H1 Retime [0]. H3 Retime [1]. Preferred setting is 1 for each bit. Setting each bit to 1 will add one cycle delay to HBLK toggle positions. Drive Strength Control for H1 [2:0], H2 [5:3], H3 [8:6], H4 [11:9], and RG [14:12]. Drive Current Values: 0 = Off, 1 = 4.3 mA, 2 = 8.6 mA, 3 = 12.9 mA, 4 = 17.2 mA, 5 = 21.5 mA, 6 = 25.8 mA, 7 = 30.1 mA. SHP/SHD Sample Control: SHP Sampling Location [5:0]. SHD Sampling Location [11:6]. DOUT Phase Control [5:0]. DCLK Mode [6]. DOUTDELAY [8:7]. 35 [14:0] 1249 DRVCONTROL 36 37 [11:0] [8:0] 00024 100 SAMPCONTROL DOUTCONTROL Table XX. CLPOB Masking Register Map Data Bit Default Address Content Value Register Name 40 41 42 [23:0] [23:0] [11:0] FFFFFF CLPMASK01 FFFFFF CLPMASK23 FFFFFF CLPMASK4 Register Description CLPOB Line Masking. Line #0 [11:0]. Line #1 [23:0]. CLPOB Line Masking. Line #2 [11:0]. Line #3 [23:0]. CLPOB Line Masking. Line #4 [11:0]. Table XXI. SG Pattern Register Map Data Bit Default Address Content Value Register Name 50 51 52 53 54 [3:0] [23:0] [23:0] [23:0] [23:0] F SGPOL Register Description Start Polarity for SG Patterns. Pattern #0 [0]. Pattern #1 [1]. Pattern #2 [2]. Pattern #3 [3]. Pattern #0. Toggle Position 1 [11:0]. Toggle Position 2 [23:12]. Pattern #1. Toggle Position 1 [11:0]. Toggle Position 2 [23:12]. Pattern #2. Toggle Position 1 [11:0]. Toggle Position 2 [23:12]. Pattern #3. Toggle Position 1 [11:0]. Toggle Position 2 [23:12]. FFFFFF SGTOG12_0 FFFFFF SGTOG12_1 FFFFFF SGTOG12_2 FFFFFF SGTOG12_3 Table XXII. Shutter Control Register Map Data Bit Default Address Content Value Register Name 60 [4:0] 0 TRIGGER Register Description Trigger for VSUB [0], MSHUT [1], STROBE [2], Exposure [3], and Readout [4]. Note that to trigger the readout to automatically occur after the exposure period, both exposure and readout should be triggered together. Number of Fields to Suppress the SUBCK Pulses after the VSG Line. Number of Fields to Suppress the SUBCK and VSG Pulses. Set = 1 to disable the VD/HD outputs during exposure (when >1 field). Number of SUBCK Pulses to Suppress after VSG Line. Number of SUBCK Pulses per Field. SUBCK Pulse Start Polarity. First SUBCK Pulse. Toggle Position 1 [11:0]. Toggle Position 2 [23:0]. Second SUBCK Pulse. Toggle Position 1 [11:0]. Toggle Position 2 [23:0]. -41- 61 62 63 64 65 66 REV. 0 [2:0] [11:0] [12] [11:0] [23:12] [0] [23:0] [23:0] 2 0 0 0 0 1 READOUT EXPOSURE VDHDOFF SUBCKSUPPRESS SUBCKNUM SUBCKPOL FFFFFF SUBCK1TOG FFFFFF SUBCK2TOG AD9995 Table XXII. Shutter Control Register Map (continued) Data Bit Default Address Content Value Register Name 67 68 69 6A 6B 6C 6D 6E 6F 70 71 [1:0] [12:0] [1:0] [23:0] [11:0] [23:0] [0] [11:0] [23:0] [11:0] [23:0] 0 1000 1 0 0 0 1 0 0 0 0 VSUBMODE VSUBON MSHUTPOL MSHUTON MSHUTOFF_FD MSHUTOFF_LNPX STROBPOL STROBON_FD STROBON_LNPX STROBOFF_FD STROBOFF_LNPX Register Description VSUB Readout Mode [0]. VSUB Keep-On Mode [1]. VSUB ON Position [11:0]. VSUB Active Polarity [12]. MSHUT Active Polarity [0]. MSHUT Manual Enable [1]. MSHUT ON Position. Line [11:0]. Pixel [23:0]. MSHUT OFF Field Position. MSHUT OFF Position. Line [11:0]. Pixel [23:12]. STROBE Active Polarity. STROBE ON Field Position. STROBE ON Position. Line [11:0]. Pixel [23:12]. STROBE OFF Field Position. STROBE OFF Position. Line [11:0]. Pixel [23:12]. Table XXIII. Register Map Selection Data Bit Default Address Content Value Register Name 7F [0] 0 BANKSELECT1 Register Description Register Bank Access from Bank 1 to Bank 2. 0 = Bank 1, 1 = Bank 2. Table XXIV. AFE Operation Register Detail Data Bit Default Address Content Value Register Name 00 [1:0] [2] [3] [4] [5] [7:6] [8] [9] 3 1 0 0 0 0 0 0 PWRDOWN CLPENABLE CLPSPEED TEST PBLK_LVL TEST DCBYP TEST Register Description 0 = Normal Operation, 1 = Standby 1, 2 = Standby 2, 3 = Standby 3. 0 = Disable OB Clamp, 1 = Enable OB Clamp. 0 = Select Normal OB Clamp Settling, 1 = Select Fast OB Clamp Settling. Test Use Only. Set to 0. DOUT Value during PBLK: 0 = Blank to Zero, 1 = Blank to Clamp Level. Test Use Only. Set to 0. 0 = Enable DC Restore Circuit, 1 = Bypass DC Restore Circuit during PBLK. Test Use Only. Set to 0. Table XXV. AFE Control Register Detail Data Bit Default Address Content Value Register Name 03 [1:0] [2] [3] [4] [5] 0 1 0 0 0 TEST TEST DOUTDISABLE DOUTLATCH GRAYENCODE Register Description Test Use Only. Set to 00. Test Use Only. Set to 1. 0 = Data Outputs are Driven, 1 = Data Outputs are Three-Stated. 0 = Latch Data Outputs with DOUT Phase, 1 = Output Latch Transparent. 0 = Binary Encode Data Outputs, 1 = Gray Encode Data Outputs. -42- REV. 0 AD9995 COMPLETE LISTING FOR REGISTER BANK 2 All V-pattern group and V-sequence registers are SCP updated, and all Field registers are VD updated. All address and default values are in hexadecimal. Table XXVI. V-Pattern Group 0 (VPAT0) Register Map Data Bit Default Address Content Value Register Name 00 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_0 UNUSED VPATLEN_0 V1TOG1_0 V1TOG2_0 V1TOG3_0 V2TOG1_0 V2TOG2_0 V2TOG3_0 V3TOG1_0 V3TOG2_0 V3TOG3_0 V4TOG1_0 V4TOG2_0 V4TOG3_0 V5TOG1_0 V5TOG2_0 V5TOG3_0 V6TOG1_0 V6TOG2_0 V6TOG3_0 FREEZE1_0 RESUME1_0 FREEZE2_0 RESUME2_0 Description VPAT0 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT0. Note: If using VPAT0 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 01 02 03 04 05 06 07 08 09 0A 0B Table XXVII. V-Pattern Group 1 (VPAT1) Register Map Data Bit Default Address Content Value Register Name 0C [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_1 UNUSED VPATLEN_1 V1TOG1_1 V1TOG2_1 V1TOG3_1 V2TOG1_1 V2TOG2_1 V2TOG3_1 V3TOG1_1 V3TOG2_1 V3TOG3_1 V4TOG1_1 V4TOG2_1 V4TOG3_1 Description VPAT1 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT1. Note: If using VPAT1 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 -43- 0D 0E 0F 10 11 12 REV. 0 AD9995 Table XXVII. V-Pattern Group 1 (VPAT1) Register Map (continued) Data Bit Default Address Content Value Register Name 13 14 15 16 17 [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 V5TOG1_1 V5TOG2_1 V5TOG3_1 V6TOG1_1 V6TOG2_1 V6TOG3_1 FREEZE1_1 RESUME1_1 FREEZE2_1 RESUME2_1 Description V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 Table XXVIII. V-Pattern Group 2 (VPAT2) Register Map Data Bit Default Address Content Value Register Name 18 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_2 UNUSED VPATLEN_2 V1TOG1_2 V1TOG2_2 V1TOG3_2 V2TOG1_2 V2TOG2_2 V2TOG3_2 V3TOG1_2 V3TOG2_2 V3TOG3_2 V4TOG1_2 V4TOG2_2 V4TOG3_2 V5TOG1_2 V5TOG2_2 V5TOG3_2 V6TOG1_2 V6TOG2_2 V6TOG3_2 FREEZE1_2 RESUME1_2 FREEZE2_2 RESUME2_2 Description VPAT2 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT2. Note: If using VPAT2 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 19 1A 1B 1C 1D 1E 1F 20 21 22 23 Table XXIX. V-Pattern Group 3 (VPAT3) Register Map Data Bit Default Address Content Value Register Name 24 [5:0] [11:6] [23:12] [11:0] [23:12] 0 0 0 0 0 VPOL_3 UNUSED VPATLEN_3 V1TOG1_3 V1TOG2_3 Description VPAT3 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT3. Note: If using VPAT3 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 -44- REV. 0 25 AD9995 Table XXIX. V-Pattern Group 3 (VPAT3) Register Map (continued) Data Bit Default Address Content Value Register Name 26 27 28 29 2A 2B 2C 2D 2E 2F [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 V1TOG3_3 V2TOG1_3 V2TOG2_3 V2TOG3_3 V3TOG1_3 V3TOG2_3 V3TOG3_3 V4TOG1_3 V4TOG2_3 V4TOG3_3 V5TOG1_3 V5TOG2_3 V5TOG3_3 V6TOG1_3 V6TOG2_3 V6TOG3_3 FREEZE1_3 RESUME1_3 FREEZE2_3 RESUME2_3 Description V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 Table XXX. V-Pattern Group 4 (VPAT4) Register Map Data Bit Default Address Content Value Register Name 30 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_4 UNUSED VPATLEN_4 V1TOG1_4 V1TOG2_4 V1TOG3_4 V2TOG1_4 V2TOG2_4 V2TOG3_4 V3TOG1_4 V3TOG2_4 V3TOG3_4 V4TOG1_4 V4TOG2_4 V4TOG3_4 V5TOG1_4 V5TOG2_4 V5TOG3_4 V6TOG1_4 V6TOG2_4 V6TOG3_4 FREEZE1_4 RESUME1_4 FREEZE2_4 RESUME2_4 Description VPAT4 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT4. Note: If using VPAT4 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 -45- 31 32 33 34 35 36 37 38 39 3A 3B REV. 0 AD9995 Table XXXI. V-Pattern Group 5 (VPAT5) Register Map Data Bit Default Address Content Value Register Name 3C [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_5 UNUSED VPATLEN_5 V1TOG1_5 V1TOG2_5 V1TOG3_5 V2TOG1_5 V2TOG2_5 V2TOG3_5 V3TOG1_5 V3TOG2_5 V3TOG3_5 V4TOG1_5 V4TOG2_5 V4TOG3_5 V5TOG1_5 V5TOG2_5 V5TOG3_5 V6TOG1_5 V6TOG2_5 V6TOG3_5 FREEZE1_5 RESUME1_5 FREEZE2_5 RESUME2_5 Description VPAT5 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT5. Note: If using VPAT5 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 3D 3E 3F 40 41 42 43 44 45 46 47 Table XXXII. V-Pattern Group 6 (VPAT6) Register Map Data Bit Default Address Content Value Register Name 48 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_6 UNUSED VPATLEN_6 V1TOG1_6 V1TOG2_6 V1TOG3_6 V2TOG1_6 V2TOG2_6 V2TOG3_6 V3TOG1_6 V3TOG2_6 V3TOG3_6 V4TOG1_6 V4TOG2_6 V4TOG3_6 V5TOG1_6 V5TOG2_6 Description VPAT6 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT6. Note: If using VPAT6 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 49 4A 4B 4C 4D 4E 4F -46- REV. 0 AD9995 Table XXXII. V-Pattern Group 6 (VPAT6) Register Map (continued) Data Bit Default Address Content Value Register Name 50 51 52 53 [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 V5TOG3_6 V6TOG1_6 V6TOG2_6 V6TOG3_6 FREEZE1_6 RESUME1_6 FREEZE2_6 RESUME2_6 Description V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 Table XXXIII. V-Pattern Group 7 (VPAT7) Register Map Data Bit Default Address Content Value Register Name 54 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_7 UNUSED VPATLEN_7 V1TOG1_7 V1TOG2_7 V1TOG3_7 V2TOG1_7 V2TOG2_7 V2TOG3_7 V3TOG1_7 V3TOG2_7 V3TOG3_7 V4TOG1_7 V4TOG2_7 V4TOG3_7 V5TOG1_7 V5TOG2_7 V5TOG3_7 V6TOG1_7 V6TOG2_7 V6TOG3_7 FREEZE1_7 RESUME1_7 FREEZE2_7 RESUME2_7 Description VPAT7 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT7. Note: If using VPAT7 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 55 56 57 58 59 5A 5B 5C 5D 5E 5F Table XXXIV. V-Pattern Group 8 (VPAT8) Register Map Data Bit Default Address Content Value Register Name 60 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 VPOL_8 UNUSED VPATLEN_8 V1TOG1_8 V1TOG2_8 V1TOG3_8 V1TOG4_8 Description VPAT8 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT8. Note: If using VPAT8 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V1 Toggle Position 4 -47- 61 62 REV. 0 AD9995 Table XXXIV. V-Pattern Group 8 (VPAT8) Register Map (continued) Data Bit Default Address Content Value Register Name 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 V2TOG1_8 V2TOG2_8 V3TOG3_8 V3TOG4_8 V3TOG1_8 V4TOG2_8 V4TOG3_8 V4TOG4_8 V5TOG1_8 V5TOG2_8 V5TOG3_8 V6TOG4_8 V6TOG1_8 V6TOG2_8 V6TOG3_8 V6TOG4_8 V6TOG1_8 V6TOG2_8 V6TOG3_8 V6TOG4_8 FREEZE1_8 RESUME1_8 FREEZE2_8 RESUME2_8 UNUSED Description V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V2 Toggle Position 4 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V3 Toggle Position 4 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V4 Toggle Position 4 V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V5 Toggle Position 4 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V6 Toggle Position 4 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 Unused Table XXXV. V-Pattern Group 9 (VPAT9) Register Map Data Bit Default Address Content Value Register Name 70 [5:0] [11:6] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VPOL_9 UNUSED VPATLEN_9 V1TOG1_9 V1TOG2_9 V1TOG3_9 V1TOG4_9 V2TOG1_9 V2TOG2_9 V3TOG3_9 V3TOG4_9 V3TOG1_9 V4TOG2_9 V4TOG3_9 V4TOG4_9 V5TOG1_9 V5TOG2_9 V5TOG3_9 V6TOG4_9 Description VPAT9 Start Polarity. V1[0]. V2[1]. V3[2]. V4[3]. V5[4]. V6[5]. Unused. Total Length of VPAT9. Note: If using VPAT9 as a second V-sequence in the VSG active line, this value is the start position for the second V-sequence. V1 Toggle Position 1 V1 Toggle Position 2 V1 Toggle Position 3 V1 Toggle Position 4 V2 Toggle Position 1 V2 Toggle Position 2 V2 Toggle Position 3 V2 Toggle Position 4 V3 Toggle Position 1 V3 Toggle Position 2 V3 Toggle Position 3 V3 Toggle Position 4 V4 Toggle Position 1 V4 Toggle Position 2 V4 Toggle Position 3 V4 Toggle Position 4 -48- REV. 0 71 72 73 74 75 76 77 78 AD9995 Table XXXV. V-Pattern Group 9 (VPAT9) Register Map (continued) Data Bit Default Address Content Value Register Name 79 7A 7B 7C 7D 7E [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 V6TOG1_9 V6TOG2_9 V6TOG3_9 V6TOG4_9 V6TOG1_9 V6TOG2_9 V6TOG3_9 V6TOG4_9 FREEZE1_9 RESUME1_9 FREEZE2_9 RESUME2_9 Description V5 Toggle Position 1 V5 Toggle Position 2 V5 Toggle Position 3 V5 Toggle Position 4 V6 Toggle Position 1 V6 Toggle Position 2 V6 Toggle Position 3 V6 Toggle Position 4 V1-V6 Freeze Position 1 V1-V6 Resume Position 1 V1-V6 Freeze Position 2 V1-V6 Resume Position 2 Table XXXVI. Register Map Selection (SCK Updated Register) Data Bit Default Address Content Value Register Name 7F [0] 0 BANKSELECT2 Register Description Register Bank Access from Bank 2 to Bank 1. 0 = Bank 1, 1 = Bank 2. Table XXXVII. V-Sequence 0 (VSEQ0) Register Map Data Bit Default Address Content Value Register Name 80 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_0 CLPOBPOL CLPOBPOL_0 PBLKPOL PBLKPOL_0 VPATSEL VPATSEL_0 VMASK VMASK_0 HBLKALT_0 UNUSED VPATREPO_0 VPATREPE_0 VPATSTART_0 HDLEN_0 PBLKTOG1_0 PBLKTOG2_0 HBLKTOG1_0 HBLKTOG2_0 HBLKTOG3_0 HBLKTOG4_0 HBLKTOG5_0 HBLKTOG6_0 CLPOBTOG1_0 CLPOBTOG2_0 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 0 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 0 PBLK Toggle Position 1 for V-Sequence 0 PBLK Toggle Position 2 for V-Sequence 0 HBLK Toggle Position 1 for V-Sequence 0 HBLK Toggle Position 2 for V-Sequence 0 HBLK Toggle Position 3 for V-Sequence 0 HBLK Toggle Position 4 for V-Sequence 0 HBLK Toggle Position 5 for V-Sequence 0 HBLK Toggle Position 6 for V-Sequence 0 CLPOB Toggle Position 1 for V-Sequence 0 CLPOB Toggle Position 2 for V-Sequence 0 81 82 83 84 85 86 87 REV. 0 -49- AD9995 Table XXXVIII. V-Sequence 1 (VSEQ1) Register Map Data Bit Default Address Content Value Register Name 88 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_1 CLPOBPOL CLPOBPOL_1 PBLKPOL PBLKPOL_1 VPATSEL VPATSEL_1 VMASK VMASK_1 HBLKALT_1 UNUSED VPATREPO_1 VPATREPE_1 VPATSTART_1 HDLEN_1 PBLKTOG1_1 PBLKTOG2_1 HBLKTOG1_1 HBLKTOG2_1 HBLKTOG3_1 HBLKTOG4_1 HBLKTOG5_1 HBLKTOG6_1 CLPOBTOG1_1 CLPOBTOG2_1 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 1 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 1 PBLK Toggle Position 1 for V-Sequence 1 PBLK Toggle Position 2 for V-Sequence 1 HBLK Toggle Position 1 for V-Sequence 1 HBLK Toggle Position 2 for V-Sequence 1 HBLK Toggle Position 3 for V-Sequence 1 HBLK Toggle Position 4 for V-Sequence 1 HBLK Toggle Position 5 for V-Sequence 1 HBLK Toggle Position 6 for V-Sequence 1 CLPOB Toggle Position 1 for V-Sequence 1 CLPOB Toggle Position 2 for V-Sequence 1 89 8A 8B 8C 8D 8E 8F Table XXXIX. V-Sequence 2 (VSEQ2) Register Map Data Bit Default Address Content Value Register Name 90 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_2 CLPOBPOL CLPOBPOL_2 PBLKPOL PBLKPOL_2 VPATSEL VPATSEL_2 VMASK VMASK_2 HBLKALT_2 UNUSED VPATREPO_2 VPATREPE_2 VPATSTART_2 HDLEN_2 PBLKTOG1_2 PBLKTOG2_2 HBLKTOG1_2 HBLKTOG2_2 HBLKTOG3_2 HBLKTOG4_2 HBLKTOG5_2 HBLKTOG6_2 CLPOBTOG1_2 CLPOBTOG2_2 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 2 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 2 PBLK Toggle Position 1 for V-Sequence 2 PBLK Toggle Position 2 for V-Sequence 2 HBLK Toggle Position 1 for V-Sequence 2 HBLK Toggle Position 2 for V-Sequence 2 HBLK Toggle Position 3 for V-Sequence 2 HBLK Toggle Position 4 for V-Sequence 2 HBLK Toggle Position 5 for V-Sequence 2 HBLK Toggle Position 6 for V-Sequence 2 CLPOB Toggle Position 1 for V-Sequence 2 CLPOB Toggle Position 2 for V-Sequence 2 91 92 93 94 95 96 97 -50- REV. 0 AD9995 Table XL. V-Sequence 3 (VSEQ3) Register Map Data Bit Default Address Content Value Register Name 98 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_3 CLPOBPOL CLPOBPOL_3 PBLKPOL PBLKPOL_3 VPATSEL VPATSEL_3 VMASK VMASK_3 HBLKALT_3 UNUSED VPATREPO_3 VPATREPE_3 VPATSTART_3 HDLEN_3 PBLKTOG1_3 PBLKTOG2_3 HBLKTOG1_3 HBLKTOG2_3 HBLKTOG3_3 HBLKTOG4_3 HBLKTOG5_3 HBLKTOG6_3 CLPOBTOG1_3 CLPOBTOG2_3 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 3 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 3 PBLK Toggle Position 1 for V-Sequence 3 PBLK Toggle Position 2 for V-Sequence 3 HBLK Toggle Position 1 for V-Sequence 3 HBLK Toggle Position 2 for V-Sequence 3 HBLK Toggle Position 3 for V-Sequence 3 HBLK Toggle Position 4 for V-Sequence 3 HBLK Toggle Position 5 for V-Sequence 3 HBLK Toggle Position 6 for V-Sequence 3 CLPOB Toggle Position 1 for V-Sequence 3 CLPOB Toggle Position 2 for V-Sequence 3 99 9A 9B 9C 9D 9E 9F Table XLI. V-Sequence 4 (VSEQ4) Register Map Data Bit Default Address Content Value Register Name A0 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_4 CLPOBPOL CLPOBPOL_4 PBLKPOL PBLKPOL_4 VPATSEL VPATSEL_4 VMASK VMASK_4 HBLKALT_4 UNUSED VPATREPO_4 VPATREPE_4 VPATSTART_4 HDLEN_4 PBLKTOG1_4 PBLKTOG2_4 HBLKTOG1_4 HBLKTOG2_4 HBLKTOG3_4 HBLKTOG4_4 HBLKTOG5_4 HBLKTOG6_4 CLPOBTOG1_4 CLPOBTOG2_4 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 4 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 4 PBLK Toggle Position 1 for V-Sequence 4 PBLK Toggle Position 2 for V-Sequence 4 HBLK Toggle Position 1 for V-Sequence 4 HBLK Toggle Position 2 for V-Sequence 4 HBLK Toggle Position 3 for V-Sequence 4 HBLK Toggle Position 4 for V-Sequence 4 HBLK Toggle Position 5 for V-Sequence 4 HBLK Toggle Position 6 for V-Sequence 4 CLPOB Toggle Position 1 for V-Sequence 4 CLPOB Toggle Position 2 for V-Sequence 4 A1 A2 A3 A4 A5 A6 A7 REV. 0 -51- AD9995 Table XLII. V-Sequence 5 (VSEQ5) Register Map Data Bit Default Address Content Value Register Name A8 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_5 CLPOBPOL CLPOBPOL_5 PBLKPOL PBLKPOL_5 VPATSEL VPATSEL_5 VMASK VMASK_5 HBLKALT_5 UNUSED VPATREPO_5 VPATREPE_5 VPATSTART_5 HDLEN_5 PBLKTOG1_5 PBLKTOG2_5 HBLKTOG1_5 HBLKTOG2_5 HBLKTOG3_5 HBLKTOG4_5 HBLKTOG5_5 HBLKTOG6_5 CLPOBTOG1_5 CLPOBTOG2_5 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 5 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 5 PBLK Toggle Position 1 for V-Sequence 5 PBLK Toggle Position 2 for V-Sequence 5 HBLK Toggle Position 1 for V-Sequence 5 HBLK Toggle Position 2 for V-Sequence 5 HBLK Toggle Position 3 for V-Sequence 5 HBLK Toggle Position 4 for V-Sequence 5 HBLK Toggle Position 5 for V-Sequence 5 HBLK Toggle Position 6 for V-Sequence 5 CLPOB Toggle Position 1 for V-Sequence 5 CLPOB Toggle Position 2 for V-Sequence 5 A9 AA AB AC AD AE AF Table XLIII. V-Sequence 6 (VSEQ6) Register Map Data Bit Default Address Content Value Register Name B0 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_6 CLPOBPOL CLPOBPOL_6 PBLKPOL PBLKPOL_6 VPATSEL VPATSEL_6 VMASK VMASK_6 HBLKALT_6 UNUSED VPATREPO_6 VPATREPE_6 VPATSTART_6 HDLEN_6 PBLKTOG1_6 PBLKTOG2_6 HBLKTOG1_6 HBLKTOG2_6 HBLKTOG3_6 HBLKTOG4_6 HBLKTOG5_6 HBLKTOG6_6 CLPOBTOG1_6 CLPOBTOG2_6 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB StartPolarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 6 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 6 PBLK Toggle Position 1 for V-Sequence 6 PBLK Toggle Position 2 for V-Sequence 6 HBLK Toggle Position 1 for V-Sequence 6 HBLK Toggle Position 2 for V-Sequence 6 HBLK Toggle Position 3 for V-Sequence 6 HBLK Toggle Position 4 for V-Sequence 6 HBLK Toggle Position 5 for V-Sequence 6 HBLK Toggle Position 6 for V-Sequence 6 CLPOB Toggle Position 1 for V-Sequence 6 CLPOB Toggle Position 2 for V-Sequence 6 B1 B2 B3 B4 B5 B6 B7 -52- REV. 0 AD9995 Table XLIV. V-Sequence 7 (VSEQ7) Register Map Data Bit Default Address Content Value Register Name B8 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_7 CLPOBPOL CLPOBPOL_7 PBLKPOL PBLKPOL_7 VPATSEL VPATSEL_7 VMASK VMASK_7 HBLKALT_7 UNUSED VPATREPO_7 VPATREPE_7 VPATSTART_7 HDLEN_7 PBLKTOG1_7 PBLKTOG2_7 HBLKTOG1_7 HBLKTOG2_7 HBLKTOG3_7 HBLKTOG4_7 HBLKTOG5_7 HBLKTOG6_7 CLPOBTOG1_7 CLPOBTOG2_7 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 7 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 7 PBLK Toggle Position 1 for V-Sequence 7 PBLK Toggle Position 2 for V-Sequence 7 HBLK Toggle Position 1 for V-Sequence 7 HBLK Toggle Position 2 for V-Sequence 7 HBLK Toggle Position 3 for V-Sequence 7 HBLK Toggle Position 4 for V-Sequence 7 HBLK Toggle Position 5 for V-Sequence 7 HBLK Toggle Position 6 for V-Sequence 7 CLPOB Toggle Position 1 for V-Sequence 7 CLPOB Toggle Position 2 for V-Sequence 7 B9 BA BB BC BD BE BF Table XLV. V-Sequence 8 (VSEQ8) Register Map Data Bit Default Address Content Value Register Name C0 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_8 CLPOBPOL CLPOBPOL_8 PBLKPOL PBLKPOL_8 VPATSEL VPATSEL_8 VMASK VMASK_8 HBLKALT_8 UNUSED VPATREPO_8 VPATREPE_8 VPATSTART_8 HDLEN_8 PBLKTOG1_8 PBLKTOG2_8 HBLKTOG1_8 HBLKTOG2_8 HBLKTOG3_8 HBLKTOG4_8 HBLKTOG5_8 HBLKTOG6_8 CLPOBTOG1_8 CLPOBTOG2_8 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 8 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 8 PBLK Toggle Position 1 for V-Sequence 8 PBLK Toggle Position 2 for V-Sequence 8 HBLK Toggle Position 1 for V-Sequence 8 HBLK Toggle Position 2 for V-Sequence 8 HBLK Toggle Position 3 for V-Sequence 8 HBLK Toggle Position 4 for V-Sequence 8 HBLK Toggle Position 5 for V-Sequence 8 HBLK Toggle Position 6 for V-Sequence 8 CLPOB Toggle Position 1 for V-Sequence 8 CLPOB Toggle Position 2 for V-Sequence 8 C1 C2 C3 C4 C5 C6 C7 REV. 0 -53- AD9995 Table XLVI. V-Sequence 9 (VSEQ9) Register Map Data Bit Default Address Content Value Register Name C8 [1:0] [2] [3] [7:4] [9:8] [11:10] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HBLKMASK_9 CLPOBPOL CLPOBPOL_9 PBLKPOL PBLKPOL_9 VPATSEL VPATSEL_9 VMASK VMASK_9 HBLKALT_9 UNUSED VPATREPO_9 VPATREPE_9 VPATSTART_9 HDLEN_9 PBLKTOG1_9 PBLKTOG2_9 HBLKTOG1_9 HBLKTOG2_9 HBLKTOG3_9 HBLKTOG4_9 HBLKTOG5_9 HBLKTOG6_9 CLPOBTOG1_9 CLPOBTOG2_9 Description Masking Polarity during HBLK. H1 [0]. H3 [1]. CLPOB Start Polarity PBLK Start Polarity Selected V-Pattern Group for V-Sequence 9 Enable Masking of V-Outputs (Specified by FREEZE/RESUME Registers) Enable HBLK Alternation Unused Number of Selected V-Pattern Group Repetitions for Odd Lines Number of Selected V-Pattern Group Repetitions for Even Lines Start Position in the Line for the Selected V-Pattern Group HD Line Length (Number of Pixels) for V-Sequence 9 PBLK Toggle Position 1 for V-Sequence 9 PBLK Toggle Position 2 for V-Sequence 9 HBLK Toggle Position 1 for V-Sequence 9 HBLK Toggle Position 2 for V-Sequence 9 HBLK Toggle Position 3 for V-Sequence 9 HBLK Toggle Position 4 for V-Sequence 9 HBLK Toggle Position 5 for V-Sequence 9 HBLK Toggle Position 6 for V-Sequence 9 CLPOB Toggle Position 1 for V-Sequence 9 CLPOB Toggle Position 2 for V-Sequence 9 Table XLVII. Field 0 Register Map C9 CA CB CC CD CE CF Data Bit Default Address Content Value Register Name D0 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL0_0 SWEEP0_0 MULTI0_0 VSEQSEL1_0 SWEEP1_0 MULTI1_0 VSEQSEL2_0 SWEEP2_0 MULTI2_0 VSEQSEL3_0 SWEEP3_0 MULTI3_0 VSEQSEL4_0 SWEEP4_0 MULTI4_0 VSEQSEL5_0 SWEEP5_0 MULTI5_0 VSEQSEL6_0 SWEEP6_0 MULTI6_0 UNUSED SCP1_0 SCP2_0 SCP3_0 SCP4_0 VDLEN_0 HDLAST_0 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1= Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 0. V-Sequence Change Position #2 for Field 0. V-Sequence Change Position #3 for Field 0. V-Sequence Change Position #4 for Field 0. VD Field Length (Number of Lines) for Field 0. HD Line Length (Number of Pixels) for Last Line in Field 0. -54- REV. 0 D1 D2 D3 D4 AD9995 Table XLVII. Field 0 Register Map (continued) Data Bit Default Address Content Value Register Name D5 [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 VPATSECOND_0 SGMASK SGMASK_0 SGPATSEL SGPATSEL_0 SGLINE1_0 SGLINE2_0 SCP5_0 SCP6_0 Description Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 0. V-Sequence Change Position #6 for Field 0. Table XLVIII. Field 1 Register Map D6 D7 Data Bit Default Address Content Value Register Name D8 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL0_1 SWEEP0_1 MULTI0_1 VSEQSEL1_1 SWEEP1_1 MULTI1_1 VSEQSEL2_1 SWEEP2_1 MULTI2_1 VSEQSEL3_1 SWEEP3_1 MULTI3_1 VSEQSEL4_1 SWEEP4_1 MULTI4_1 VSEQSEL5_1 SWEEP5_1 MULTI5_1 VSEQSEL6_1 SWEEP6_1 MULTI6_1 UNUSED SCP1_1 SCP2_1 SCP3_1 SCP4_1 VDLEN_1 HDLAST_1 VPATSECOND_1 SGMASK SGMASK_1 SGPATSEL SGPATSEL_1 SGLINE1_1 SGLINE2_1 SCP5_1 SCP6_1 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 1. V-Sequence Change Position #2 for Field 1. V-Sequence Change Position #3 for Field 1. V-Sequence Change Position #4 for Field 1. VD Field Length (Number of Lines) for Field 1. HD Line Length (Number of Pixels) for Last Line in Field 1. Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 1. V-Sequence Change Position #6 for Field 1. D9 DA DB DC DD DE DF REV. 0 -55- AD9995 Table XLIX. Field 2 Register Map Data Bit Default Address Content Value Register Name E0 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL_2 SWEEP0_2 MULTI0_2 VSEQSEL1_2 SWEEP1_2 MULTI1_2 VSEQSEL2_2 SWEEP2_2 MULTI2_2 VSEQSEL3_2 SWEEP3_2 MULTI3_2 VSEQSEL4_2 SWEEP4_2 MULTI4_2 VSEQSEL5_2 SWEEP5_2 MULTI5_2 VSEQSEL6_2 SWEEP6_2 MULTI6_2 UNUSED SCP1_2 SCP2_2 SCP3_2 SCP4_2 VDLEN0_2 HDLAST_2 VPATSECOND_2 SGMASK SGMASK_2 SGPATSEL SGPATSEL_2 SGLINE1_2 SGLINE2_2 SCP5_2 SCP6_2 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 2. V-Sequence Change Position #2 for Field 2. V-Sequence Change Position #3 for Field 2. V-Sequence Change Position #4 for Field 2. VD Field Length (Number of Lines) for Field 2. HD Line Length (Number of Pixels) for Last Line in Field 2. Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 2. V-Sequence Change Position #6 for Field 2. Table L. Field 3 Register Map E1 E2 E3 E4 E5 E6 E7 Data Bit Default Address Content Value Register Name E8 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL_3 SWEEP0_3 MULTI0_3 VSEQSEL1_3 SWEEP1_3 MULTI1_3 VSEQSEL2_3 SWEEP2_3 MULTI2_3 VSEQSEL3_3 SWEEP3_3 MULTI3_3 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. -56- REV. 0 AD9995 Table L. Field 3 Register Map (continued) Data Bit Default Address Content Value Register Name E9 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [11:0] [23:12] [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL4_3 SWEEP4_3 MULTI4_3 VSEQSEL5_3 SWEEP5_3 MULTI5_3 VSEQSEL6_3 SWEEP6_3 MULTI6_3 UNUSED SCP1_3 SCP2_3 SCP3_3 SCP4_3 VDLEN_3 HDLAST_3 VPATSECOND_3 SGMASK SGMASK_3 SGPATSEL SGPATSEL_3 SGLINE1_3 SGLINE2_3 SCP5_3 SCP6_3 Description Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 3. V-Sequence Change Position #2 for Field 3. V-Sequence Change Position #3 for Field 3. V-Sequence Change Position #4 for Field 3. VD Field Length (Number of Lines) for Field 3. HD Line Length (Number of Pixels) for Last Line in Field 3. Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 3. V-Sequence Change Position #6 for Field 3. Table LI. Field 4 Register Map EA EB [23:12] EC ED EE EF Data Bit Default Address Content Value Register Name F0 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL0_4 SWEEP0_4 MULTI0_4 VSEQSEL1_4 SWEEP1_4 MULTI1_4 VSEQSEL2_4 SWEEP2_4 MULTI2_4 VSEQSEL3_4 SWEEP3_4 MULTI3_4 VSEQSEL4_4 SWEEP4_4 MULTI4_4 VSEQSEL5_4 SWEEP5_4 MULTI5_4 VSEQSEL6_4 SWEEP6_4 MULTI6_4 UNUSED SCP1_4 SCP2_4 SCP3_4 SCP4_4 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 = No Multiplier, 1 = Multiplier.. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 4. V-Sequence Change Position #2 for Field 4. V-Sequence Change Position #3 for Field 4. V-Sequence Change Position #4 for Field 4. -57- F1 F2 F3 REV. 0 AD9995 Table LI. Field 4 Register Map (continued) Data Bit Default Address Content Value Register Name F4 F5 [11:0] [23:12] [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 VDLEN_4 HDLAST_4 VPATSECOND_4 SGMASK_4 SGPATSEL_4 SGLINE1_4 SGLINE2_4 SCP5_4 SCP6_4 Description VD Field Length (Number of Lines) for Field 4. HD Line Length (Number of Pixels) for Last Line in Field 4. Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 4. V-Sequence Change Position #6 for Field 4. Table LII. Field 5 Register Map F6 F7 Data Bit Default Address Content Value Register Name F8 [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [21:18] [22] [23] [3:0] [4] [5] [9:6] [10] [11] [15:12] [16] [17] [23:18] [11:0] [23:12] [11:0] [23:12] [11:0] [23:12] [3:0] [9:4] [21:10] [11:0] [23:12] [11:0] [23:12] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VSEQSEL0_5 SWEEP0_5 MULTI0_5 VSEQSEL1_5 SWEEP1_5 MULTI1_5 VSEQSEL2_5 SWEEP2_5 MULTI2_5 VSEQSEL3_5 SWEEP3_5 MULTI3_5 VSEQSEL4_5 SWEEP4_5 MULTI4_5 VSEQSEL5_5 SWEEP5_5 MULTI5_5 VSEQSEL6_5 SWEEP6_5 MULTI6_5 UNUSED SCP1_5 SCP2_5 SCP3_5 SCP4_5 VDLEN_5 HDLAST_5 VPATSECOND_5 SGMASK_5 SGPATSEL_5 SGLINE1_5 SGLINE2_5 SCP5_5 SCP6_5 Description Selected V-Sequence for Region 0. Select Sweep Region for Region 0. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 0. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 1. Select Sweep Region for Region 1. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 1. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 2. Select Sweep Region for Region 2. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 2. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 3. Select Sweep Region for Region 3. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 3. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 4. Select Sweep Region for Region 4. 0 = No Sweep, 1 = Sweep Select Multiplier Region for Region 4. 0 = No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 5. Select Sweep Region for Region 5. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 5. 0 =No Multiplier, 1 = Multiplier. Selected V-Sequence for Region 6. Select Sweep Region for Region 6. 0 = No Sweep, 1 = Sweep. Select Multiplier Region for Region 6. 0 = No Multiplier, 1 = Multiplier. Unused. V-Sequence Change Position #1 for Field 5. V-Sequence Change Position #2 for Field 5. V-Sequence Change Position #3 for Field 5. V-Sequence Change Position #4 for Field 5. VD Field Length (Number of Lines) for Field 5. HD Line Length (Number of Pixels) for Last Line in Field 5. Selected Second V-Pattern Group for VSG Active Line. Masking of VSG Outputs during VSG Active Line. Selection of VSG Patterns for Each VSG Output. VSG Active Line 1. VSG Active Line 2 (if no Second Line Needed, Set to Same as Line 1 or Max). V-Sequence Change Position #5 for Field 5. V-Sequence Change Position #6 for Field 5. F9 FA FB FC FD FE FF -58- REV. 0 AD9995 OUTLINE DIMENSIONS 56-Lead Lead Frame Chip Scale Package [LFCSP] 8 mm 8 mm Body (CP-56) Dimensions shown in millimeters 8.00 BSC SQ 0.60 MAX 0.60 MAX 42 43 0.30 0.23 0.18 56 1 PIN 1 INDICATOR PIN 1 INDICATOR TOP VIEW 7.75 BSC SQ BOTTOM VIEW 6.25 6.10 SQ 5.95 0.50 0.40 0.30 0.80 MAX 0.65 NOM 0.05 MAX 0.02 NOM 0.50 BSC SEATING PLANE COPLANARITY 0.08 29 28 15 14 1.00 0.90 0.80 0.20 REF 6.50 REF 0.25 MIN 12 MAX COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2 REV. 0 -59- -60- C04336-0-8/03(0) |
Price & Availability of AD9995 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |