View MC33174_30929.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC33174 - MC35174
LOW POWER QUAD BIPOLAR OPERATIONAL AMPLIFIERS
s GOOD CONSUMPTION/SPEED RATIO :
ONLY 200A FOR 2.1MHz, 2Vs
s SINGLE (OR DUAL) SUPPLY OPERATION
FROM +4V TO +44V (2V TO 22V)
s WIDE INPUT COMMON MODE MODE
VOLTAGE RANGE INCLUDING VCC-
s LOW LEVEL OUTPUT VOLTAGE CLOSE TO
VCC- : 100mV TYPICAL
N DIP14 (Plastic Package)
s PIN TO PIN COMPATIBLE WITH
STANDARD QUAD OP-AMPs DESCRIPTION The MC3x174 series are quad bipolar operational amplifier offering both low consumption (200A) and good speed (2.1MHz, 2V/s). Moreover the Input Common Mode Range extends down to the lower supply rail, allowing single supply operation from +4V to +44V. ORDER CODE
Output 1 1 14 Output 4 + + 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC + + 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3
D SO14 (Plastic Micropackage)
PIN CONNECTIONS (top view)
Part Number
Temperature Range
Package N * * D * *
Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7
MC33174 -40C, +105C MC35174 -55C, +125C Example : MC33174N
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT))
April 2002
1/5
MC33174-MC35174
SCHEMATIC DIAGRAM (for 1/4 MC33174)
VCC +
R4
R5
R6
T7 T1
T8
T9 R7 R3 T15
T10 R8
T11
T12
T13
T25 T16 T17 R13
Input +
T24 T26
T6
Input -
T14 C T5 T2 T13 T21 T22
R12 R14
Output
T19 T3 T4 R2 R1 R9 R10 R11 T20
T27 T29 T23 R15
T28
T30
T31
VCC -
MAXIMUM RATINGS
Symbol VCC Vid Vi Toper Tj Tstg
1.
Parameter Supply Voltage Differential Input Voltage Input Voltage Output Short Circuit Duration Operating Free-Air Temperature range Junction Temperature Storage Temperature
Value 22 see note 1) see note 1 Indefinite -40 to 105 -55 to 125 150 -65 to 150
Unit V V V s C C C
MC33174 MC35174
Either or both input voltages must not exceed the magnitude of Vcc.
OPERATING CONDITIONS
Symbol VCC Supply Voltage Parameter Value 2 to 22 Unit V
2/5
MC33174-MC35174
ELECTRICAL CHARACTERISTICS VCC+ = +15V, VCC- = -15V, R L connected to Ground, Tamb = 25C (unless otherwise specified)
Symbol Parameter Input Offset Voltage VCC+ = +15V, VCC- = -15V, Vic = 0V VCC+ = 5V, VCC- = 0V, Vic = 0V, Vo = 1.4V VCC = +15V, VCC = -15V, Vic = 0V, Tmin. Tamb Tmax.
+ -
Min.
Typ.
Max.
Unit
Vio
1 1 10 5
4.5 5 6.5
mV
DVio Iio Iib Avd
Input Offset Voltage Drift Input Offset Current (Vic = 0V) Tmin. Tamb Tmax. Input Bias Current (Vic = 0V) Tmin. Tamb Tmax. Large Signal Voltage Gain (RL = 10k, Vo = 10V) Tmin. Tamb Tmax. High Level Output Voltage VCC+ = 5V, VCC- = 0V, RL = 10k VCC+ = +15V, VCC- = -15V, RL = 10k VCC = +15V, VCC = -15V, RL = 10k, Tmin. Tamb Tmax
+ -
V/C 20 40 100 200 nA nA V/mV
20 50 25 3.5 13.6 13.3 100
VOH
4.2 14.2
V
VOL
Low Level Output Voltage VCC+ = 5V, VCC- = 0V, RL = 10k VCC+ = +15V, VCC- = -15V, RL = 10k VCC+ = +15V, VCC- = -15V, RL = 10k, Tmin. Tamb Tmax Output Short Circuit Current (Vid = 1V, Vo = 0V) Source Sink Input Common Mode Voltage Range Tmin. Tamb Tmax Common-mode Rejection Ratio (Vic = Vicm min.) Supply Voltage Rejection Ratio (VCC = 5 to 15V) Supply Current VCC+ = 5V, VCC- = 0V, no load VCC+ = +15V, VCC- = -15V, no load VCC+ = +15V, VCC- = -15V, no load, Tmin. Tamb Tmax Slew Rate (Vi = 10V, RL = 10k, CL = 100pF) Gain Bandwidth Product RL = 10k, CL = 100pF, f = 100kHz Phase Margin (RL = 10k, CL = 100pF) Equivalent Input Noise Voltage (f = 1kHz) 1.6 1.4
0.1 -14
0.15 -13.6 -13.3
V
Isc
3 15 VCC- to (VCC+ - 1.8) VCC- to (VCC+ - 2.2) 80 80
6 27
mA
Vicm CMR SVR
V 100 100 200 220 2 2.1 45 29 0.05 120 250 250 300 dB dB
ICC
A
SR GBP m en
V/s MHz Degrees nV ----------Hz % dB
THD Total Harmonic Distortion VO1/VO2 Channel Separation
3/5
MC33174-MC35174
PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP
Millimeters Dimensions Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055
Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100
4/5
MC33174-MC35174
PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO)
L C
G c1
a2 b e3 D M e
A
s E
14 1
8 7 F
Millimeters Dimensions Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45 (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007
a1
Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States (c) http://www.st.com
b1
5/5

▲Up To Search▲

Price & Availability of MC33174

	To Download MC33174 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .